Vivotek IP9165-LPC-A User manual

IP Surveillance
Installation Guide
IP9165-LPC-A
License Plate Capturing Solution
(Street)
Rev. 1.0
Ordering part no.:
IP9165-LPC-A (Street): 199004500G
Document part no.: 625048300G

2
Specications
I
Model Number LPC enclosure
Power Input 24V AC
Max. Output power budget 48W (Street);
Power Consumption Window heater: 10W; Blower: 2W; Camera: 6 ~ 8W
Environmental Operation Temp. -20°C ~ +50°C (-4°F ~ +149°F)
Protection Level IP68, IK10
Mounting Bracket Fully-cable Management
Construction Die-cast Aluminum Alloy
Coating White epoxy powder coating
Dimensions 502.8 (L) x 170 (W) x 400 (H) mm
Net Weight 6,482g (9.24 lb)
CAUTION:
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
UNPACKING:
Unpack carefully. Electronic components can be damaged if improperly handled or
dropped. If an item appears damaged in shipment, place it properly in its carton and
notify the shipper.
IMPORTANT!:
1. Read and follow Instructions: All operating and user instructions should be read and
followed before the unit is to be operated.
2. Electrical Connections: Only a qualied electrician is allowed to make electrical
connections.
AM-21E
Below are the mounting hole dimensions for the mounting brackets. Chances are you may
need to plan for the locations of the brackets.

3
English
Mounting Conguration & Dimensions
II
Swivel Positions and Directions
226 mm
318 mm
108 mm
105 mm
502.8 mm
135.5 mm 158.5 mm
170 mm
400 mm
77.4 mm
USABLE
AREA
255 mm
USABLE AREA
415 mm
206.9 mm
170 mm
400 mm
135 mm
88.05 mm
87.01 mm
AE-23A
AI-109
AE-21E

4
Installation Suggestions
IV
If you plan to install this camera enclosure into a tropical, sea coastal, or an environment
where salt water or corrosive industrial waste water/moist are present, please seal each
stainless steel screws and ttings with a silicon grease compounds. This will help prevent
electrolysis to occur and extend the life span of the camera and housing.
IMPORTANT:
1. Disconnect devices: A readily accessible disconnect device in the building installation wiring
should be incorporated.
2. Electrical Connection: Only a qualied electrician is allowed to make electrical connections.
Component Description
III
• Please avoid eye exposure or apply appropriate protection, such as wearing a pair of Infrared
protection glasses, when working with the product. Always use camera live view to oberve IR
lighting effects.
WARNING:
Camera Mounting Platform
M16 1/2" Waterproof cable glands
AC/DC or PoE Power
distribution board
Ventilation fan Window frame
heater coil
VAIR module
Ground

5
English
Installation
V
1. Install the wall-mount bracket to a preferred location at your installation site. Drill
mounting holes and a cable routing hole (if preferred) on a wall. Install the bracket.
Prepare and route the wiring, Ethernet and 24V power source.
Note that the AC 110V-to-24V power adapter should have a capcity of at least 4A.
2. If you need to install an IR illuminator, remove the metal cover from the bottom of the
housing using a T15 anti-tamper screwdriver.

6
4. Prepare power wires, a ground wire, and a CAT5e Ethernet cable. Pass them through
the M16 waterproof connectors under the housing.
Ethernet cable Ø4 ~ 6.5mm
Power wires & DI/DO wires,
a combo cable from IR illuminator
(if applied)
3. Orient and secure the IR illuminator to the housing using the 4 mounting holes at the
bottom.

7
English
5. When done, tighten up and install the waterproof connectors.
6. Assemble the camera components, e.g., the CS ring and lens module. Secure the
mounting plate to the bottom of the camera (the label side) using the included screw.
There is a plastic mount pad in the package. You do not need the mounting pad
using the VIVOTEK camera.
o
O
g
B
b
G
br
BR
1
2
3
4
5
6
7
8
o: white/orange stripe
O: orange solid
g: white/green stripe
B: blue solid
b: white/blue stripe
G: green solid
br: white/brown stripe
BR: brown solid
You may need to remove the RJ45 connector, and use a crimping tool to connect the
Ethernet wires to an RJ45 connector inside the enclosure. Use an Ethernet cable of the
width of 4 ~ 6.5mm.

8
7. Adjust the camera's position so that the lens module can ush align with the tempered
glass. Secure the camera using the screws and washers to the bottom of the housing.
8. Connect 24V power source to the power input terminal. Connect power wires from the
DC 12V output to the camera. Below is the distribution board drawing power from 24V AC/
DC.
Lens flush
w/ edge of
enclosure
Heater
Blower
IR angle selector
I/O terminal block
Camera heater
24V AC/DC IN 12V DC OUT
24V AC/DC OUT
Connectors to the front IR
Power LED

9
English
You should prepare a power adaptor of the sufcient capacity for supplying 24V input.
Below are the requirements:
Total consumption Power adaptor
LPC Street 48W 4A
10. Also pass the combo cable of the IR illuminator through a waterproof connector.
11. Connect the day/night signal lines from the housing to the DI/DO connectors on the
camera's terminal block.
12345678910
9. Connect the Ethernet cable to the camera's RJ45 socket.
AWG26
AC24V
AWG20
DO2
DI2
DI-
RS485-
RS485+
DO1
DI1
DO+
DC12V
Tank ctrl
Wiper ctrl
GND
IR LED
IR ctrl
5V VCC
Camera Terminal Block
Enclosure Terminal Block
DI1+ DO2- DI2+ DI- RS485- RS485+
AC/DC+ PW AC/DC- PW
DO1- DO+ (5V)

10
Below are the parameters of the IR illuminator. Use the onboard jumpers to congure the
beam angle for a different effective illumination range.
VAIR 48W
no. of LEDs 18P/Dual
Beam angle 10°20°25°30°
Distance (meter) 350m 280m 210m 150m
Conguring IR illuminator
The following enclosures comes with adjustable IR
lights: AE-23A
LL LH HL HH