SETUP
Turn on the power supply unit or commutator BKM
Set up image brightness and saturation
/ + / -
Adjusting image brightness
/+ /-
Adjusting image saturation
-/+/-
Note BKM
Changing ring volume
Note
Calls from doorstation
Note
Calls from door bell button
Calls to Concierge
Operation with commutator BKM
BKM
BKM
Notes.
Before turning the power on, make sure that there is no misconnection or risk of short circuit.
The monitor LED is illuminating with green light. If the LED remains dim, the Monitor is in the sleep mode (calls are ignored,
and all buttons except for are disabled). To switch the Monitor on, press briefly the button.
To select and adjust image settings use buttons (brightness) and (saturation).
Press . Image from the doorstation camera is appearing on the screen, and the LED is illuminating with green light.
- Press the button The LED is illuminating with orange light. Press , or . The LED is flashing with orange to
green light. When the lowest or the highest degree of brightness is reached, the LED flashing stops.
The Monitor quits the setup mode if no button is pressed within 5 seconds. The LED starts illuminating with
green light.
- Press the button The LED is illuminating with orange light. Press , or . The LED is flashing with orange to
green light. When the lowest or the highest degree of saturation is reached, the LED flashing stops.
The Monitor quits the setup mode if no button is pressed within 5 seconds. The LED starts illuminating with
green light.
When the Monitor is connected through the Commutator , you can set up image brightness and saturation
individually for each camera connected to the commutator (doorstation cameras, an outdoor camera). For individual
settings, select a connected camera by pressing the button, and follow the above setting procedures
Pick up the handset
Shift the ring volume switch either to the left (for a quiet ring sound), or to the right (for a loud ring sound).
The position of the ring volume switch also influences intercom volume. Remember to shift the ring volume
switch to the right (loud) before starting intercom.
When a call is made from the doorstation, the Monitor is ringing. Image from the doorstation camera is displayed on the
screen.
To release the door lock, push the lock release button either on the handset, or on the Monitor. After you release the button,
intercom is still available. Hang up the handset. The screen will shut off, and the monitor will go to stand-by.
You can unlock the door without picking up the handset. When called, just press the lock release button on the
Monitor After you release the button, the Monitor will go to stand-by.
When the door bell button is pressed, the Monitor is ringing and the screen switches on.
Push image from the doorstation camera is displayed on the screen.
Pick up the handset
Press and hold the lock release button on the handset, until the Monitor LED illuminates with indicates
that the call to the Concierge has started (for details on “Subscriber - Concierge” intercom, please refer to the Concierge
Console operating instruction)
Full information on operation with commutators is given in operating instructions on corresponding commutators.
Operation of the Monitor VIZIT-M427C is similar to other monitors specified in operating instructions.
To activate the individual doorstation, push to select the channel with image from the corresponding doorstation.
Check up the image from the individual doorstation, then pick up the handset and press and hold the lock release button on
the handset, until the Monitor LED illuminates with red light. Release the button. The doorstation is active now, meaning
duplex intercom with the doorstation is engaged on your initiative.
.
.
-
.
-
.
-.
-
.
.
-,
-.
-
.
1.
2. To call the Concierge when the Monitor is connected through commutators : push to select a
corresponding channel. Pick up the handset and press and hold the lock release button on the handset, until the Monitor
LED illuminates with red light. Release the button.
/+
/
.
.
FUNCTIONAL CHECK AND OPERATION ORDER
BKM-440, -440M, -441
automatically,
automatically,
Pick up the handset and check duplex intercom.
red light. Red LED
www. 27С 201 -VIZIT-M4 Operating Instruction (revision 5 11)vizit.eu 10 11/
