VIZU Auto Breader User manual





Vizu mobile breading station with motorised rotary sieve, for dividing re-usable flour
& dough balls for discarding.
VIZU®AutoBreader
VI005AB






VIZU AUTO BREADER Specification Page
Model VI005AB
Dimensions
Height
Width
Depth
Machine
1045mm
710mm
645mm
Weight 43kg
Electrical
Running Amps
Connection Type
International Option
1 phase , 50Hz AC, 230 V, .01kw
2m BESCHUKO Euro cable with, MFEUROCONVERT
Euro to UK converter plug
N/A





All Vizu Auto Breaders have been tested and checked for proper operation before
leaving the factory.
Upon delivery please check the unit for damage. If the unit is damaged, contact the
carrier, or Fast Food Systems, immediately and file a damage claim (found in the
back of the manual). Please retain all packing materials.
Damage must be reported within 7 days of delivery
General Description
The Vizu mobile breading station is a motorised rotary sieve used for dividing re-usable flour
& dough balls.
Assembly Instructions
1. Remove all packaging.
2. Remove any protective plastic covering from panels.
3. Wash all removable items in warm soapy water.
4. Wipe all surfaces with proprietary stainless steel cleaner, or a warm damp cloth.
5. Dry all items thoroughly.
Installation
Position the Auto Breader in desired position, close to a suitable electrical supply, lock
wheels in position and connect to supply. The unit is supplied with a 13 amp, 3-pin UK plug,
fitted with a 5amp fuse.





Operating Instructions (VI005AB)
1. Remove steel plug from large pan.
2. Using the steel plug push the breading through the hole onto the sieve.
3. Once the sieve compartment is full – or you have added enough breading for your
requirements replace the stainless steel plug.
4. Press the ‘red’ ON/OFF emergency stop button. The countdown timer will now be
illuminated showing the factory pre-set of 15 seconds. If this display is not illuminated
check that the machine is plugged in and wall switch is on.
5. Make sure the tray and ½ trays are in position on the slides under the shelf of the
machine.
6. Press the ‘green’ switch and the machine will run. (FIG.1)
Figure 1: Green button to turn on machine.






DO NOT LIFT PLUG OUT AS BREADING WILL BE FLICKED OUT WHICH IS
POTENTIALLY DANGEROUS
7. If the machine needs to be stopped press the ‘red’ ON / OFF emergency stop button.
This will stop the machine. It will be switched off and display will not be illuminated.
8. To resume operation the ‘red’ button will need to be pulled out to switch the machine
back on.
9. Repeat step 6
10. Once the machine has run through its program, the display will re-set to its start time of
15 seconds. If the machine is required again, repeat step 1 – 9 otherwise presses the
‘red’ button to switch OFF.
11. The sieved breading will now be in the bottom tray – ready for use.
Note: - Due to the double action of the ‘Red’ push button care must be taken to only push
once when stopping the machine, to avoid re-energising of the unit.






Cleaning (VI005AB)
Disconnect from power supply.
Remove the stainless steel pans and wash in warm soapy water, dry thoroughly with
a soft dry cloth.
Remove both pan supports from the Breader frame
Lift the lid off the sieve






Unlatch the drop catch on the side of the motor box and slide the motor box over 2
to 3 inches. This disengages the motor.
Holding the breading compartment the brush can now be slid back in the direction of
the drive side – removing the end of the shaft from the bearing on the breading
compartment.
The brush can now lifted out.
Once all the parts have been removed they must be washed in warm soapy water to remove
all traces of flour and breading mix.
The machine should NOT be re-assembled until all the parts have been thoroughly dried.
Follow steps 1 – 8 in reverse order.





Wiring Diagram






Exploded Diagram





Exploded Diagram





Exploded Diagram





Spare Parts Listing
PART NO. DESCRIPTION QTY. IMAGE
MF005ALABEL Label For Autobreader 110 x 0.5 x 145mm 1
MFPLCASTOR Swivel castor without brakes Ø125 expander
wheel 2
MFPLCASTORB Swivel castor with brakes Ø125 braked wheel 2
MFTIMER 90 Min Countdown 1
BESCHUKO H05Rr-F 2Mtr. Rubber C032 1
MFEUROCONVERT Euro to UK converter plug In black 19-1032 1
MF20-32 Nylon Bush Rear For Man+Auto Breada 1
MF61-29 Motor Drive Bar to Suit Brush 1
MF504-341 Transformer 1
MF817-8877 Black Nylon 66, strain relief cable bush 1
MF02-2550/61-28 Auto Breader Brush Assembly Complete 1





PART NO. DESCRIPTION QTY. IMAGE
MF354Z 2 Pole 5amp term block TB06 2
MF193-026 Bridge Rectifier Quad SKB25/02 17A 1600V 1
MF330-8638 Push Button Zb4-Ba31 Non-Illuminated 1
MF795-1318 Red mushroom push button 1
MF374-1029 10mm low profile lens indicator 230VAC 1
GSGAST90262 1/2GN pan 150mm deep 2
GSGAST90062 1/1GN 150mm deep 2
GSGAST90562 2/4GN pan 150mm deep 1
MFM8X38ALLS Small S/S Anti-Loose Latch M3 X 38 MM 1 Z24 b11
GSGAST93100 1/1GN solid s/s lid 1
GSGAST94200 1/2 lid slotted cover 2
MF61-20 Locating Pin 2





Fault Finding
Qualified personnel must only carry out any servicing.
Machine must be removed from electrical supply before any servicing.
Vizu Auto Breader VI005AB
Problem Probable Cause Solution
1. Count down timer will
not illuminate.
Not plugged in
Not switch ‘ON’ at plug.
Check machine switch is
‘ON’.
Check wall switch is ’ON’
Press Emergency Stop to
reset
2. Breader does not
function.
Emergency switch
accidentally pressed.
Defective ‘ON / OFF’ switch.
Fuse in plug faulty
Loose / broken connection.
Check external currant
breaker is ‘ON/IN’ at main
supply board.
Check fuse in 3 pin plug
Check all connections
Tighten or replace switch
connectors or wiring.
Replace switch
Replace motor
3. Count down timer
illuminated-motor does not
work
Start switch disconnected.
Start switch faulty/broken.
Transformer/rectifier broken
or disconnected
Motor burnt out
Check connections on
reset switch.
Replace switch.
Check connections on
rectifier& transformer

Replace motor





Terms and Conditions
Claims
No claim shall be entertained by the Company unless made in writing. Claims arising from
damage or partial loss in transit must reach the Company within 7 days from the date of
delivery. Claims for non-delivery must reach the Company within 10 days from the date of
dispatch. All other claims must reach the Company within 7 days. Damaged goods must be
retained for inspection/collection.
Returns
The Company does not operate a returns policy unless the goods are defective:
In circumstances where the Company agrees to accept return of goods, a charge of 25% of
the invoice value will be made.





DAMAGE CLAIM FORM
Machine: VIZU Auto Breader
Product code: VI005AB
Customer name……………………………………………………………
Date of delivery……………………………………………………………
Machine serial number…………………………………………………
Damage comments………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………
Please indicate on the picture where the unit is damaged
Courier name…………………………………………………………………
Please cut this page out and post to Fast Food Systems
(The address is on the back of this manual)





Warranty
UNITED KINGDOM AND REPUBLIC OF IRELAND
Excepting where otherwise specified all products are subject to 12 months parts and labour warranty
Goods found defective will be repaired, credited or replaced without charge according to the terms of
the Company’s standard warranty, provided written notice is given within the guarantee period. In
no case will the company be liable for repairs made without its knowledge or sanction, or for indirect
damage, or any consequential loss or expense incurred by purchasers.
Fast Food Systems Ltd, warrants to the original purchaser that the equipment supplied to be free
from defective materials or workmanship for a period of 12 (twelve) months.
The following are NOT covered by warranty:
1. Failure or breakdown caused by incorrect installation.
2. Glass parts, electric lamps or door seals.
3. Adjustment or calibration of controls - this is a routine maintenance function.
4. Abuse or misuse, including cleaning.
5. Warranty labour is only carried out during normal working hours; calls attended to out of
hours may be subject to surcharges.
6. The warranty will commence either on installation or 1 (one) month from date of dispatch -
whichever is the sooner.
7. Warranty on spare parts purchased for equipment outside of the warranty period is 3 (three)
months from date of sale.
8. Any faulty spare parts replaced under warranty must be returned with 7 days of supply.
9. Warranty is non-transferable.
Fast-Food-Systems Ltd will not be held responsible, financially or otherwise, for any loss of business as a result
of equipment breakdown.










Note…





Note…