VM5 Lighting Solutions MAXIM Series User manual

VM5 Lighting Solutions
INSTALLATION INSTRUCTION
Features:
Product name: Vapor Tight
IP66 Rated
Suitable for Damp & Wet locations,All Indoor Applications
Operating voltage: AC 120-277 50/60HzV
Driver: Meanwell driver
LED Type:Samsung 5630
Technical data:
Model Power L(inch) W(inch) H(inch) LF(inch)
MVT-40-38-C
MVT-40-38-F
MVT-50-38-C
MVT-50-38-F
MVT-40-48-C
MVT-40-48-F
MVT-50-48-C
MVT-50-48-F
MVT-50-75-C
MVT-50-75-F
38W
48W
75W
4.7 4.3
45.7
61.4
30
43
LF
4.7 4.3
Safety Notice:
1.Electrical installation should be performed by a licensed electrican only
2.Disconnect the luminaire from the power supply and let cool down before any
maintenance is performed.All maintenance should be performed by a
lisensed electrician only!
3.Never touch the LED’s while luminaire is energized
4.Please contact your local representative for more information
1
13100 Alondra Blvd.,#106,Cerritos,CA
90703 Email:[e-mail]
Toll Free:844.VM5.Light
ON-OFF Function:
Introduction:
Automatic switching based on motion and light level.
Operating voltage 120~277Vac, 50/60Hz
Rated load
120V AC: 200W(inductive), 400W (resistive),
220-240V AC:
HF system 5.8GHz±75MHz, ISM wave band
Transmitting power <0.5mW
Power consumption ≤0.5W(standby), <1W(operation)
Detection zone Max.(D x H): 10m x 6m
Detection sensitivity 25% / 50% / 100%
Hold time 5s / 1min / 5min / 15min / 30min
Daylight sensor 5lux / 10lux / 20lux / 30lux / 50lux /Disable
Mounting height 8m Max.
Motion detection 0.5~3m/s
Detection angle 150°(wall installation)
360°(ceiling installation)
Operating temperature -20℃~50℃
IP rating IP20
400W(inductive), 800W (resistive)
277V AC: 400W(inductive), 800W (resistive)
Setting
By selecting the combination on the DIP switch,sensor data can be precisely set for
each specific application.
123
5S
1min
5min
15min
30min
5lux
1234
10lux
20lux
30lux
50lux
Disable
100%
50%
25%
Detection area
Detection area can be reduced by selecting the combination on the
DIP switches to fit precisely each application.
Hold time
Refers to the time period the lamp remains at 100% illumination after
no motion detected.
Daylight sensor
The sensor can be set to only allow the lamp to illuminate below a
defined ambient brightness threshold.
When set to Disable mode, the daylight sensor will switch on the lamp
when motion is detected regardless of ambient light level. 4
This is an
and switch off after a hold time when there is no motion detected. Aa built-in
daylight sensor can read brightness value, the sensor does not switch on the
light if with sufficient natural light.
innovative motion sensor, switch on the light on detection of movement,
Tel: [phone] | (1.844.VM5.LIGHT) | Fax: [phone]
1951 S. Parco Ave., Unit A
Ontario, CA 91761
INSTALLATION INSTRUCTIONS
MA X I MTM SERIES
LED VAPOR TIGHT - WATERPROOF

Instruction of installation:
Note:DO NOT drill holes on any part of the luminaire
Mounting
Drill 0.234 hole and press 6x30 screw anchor in the wall,fix the mounting bracket
on the wall by St4x30 bolt
Turn off the power Insert screw anchor in the mounting surface,
attach mounting brackets with screws
0.234inch
B
C
D
E
F
1.Snap the fixture into the mounting clips. Confirm that the fixture is
securely mounted
Suspending Mounted
G
Turn on the power
3 2
Open the clips See A below Remove diffuser See B below Remove gear tray See C below
Affix gear tray to the housing
1inch
ON
OFF
These waterproof luminaires may be wall mounted (Above 4 ft from the ground)
or ceiling mounted, are IP66 rated, and are suitable for damp and wet location
applications,as well as all indoor applications
2.If wall mounted,suitable for mounting within 4 ft of the ground

Instruction of installation:
Note:DO NOT drill holes on any part of the luminaire
Mounting
Drill 0.234 hole and press 6x30 screw anchor in the wall,fix the mounting bracket
on the wall by St4x30 bolt
Turn off the power Insert screw anchor in the mounting surface,
attach mounting brackets with screws
0.234inch
B
C
D
E
F
1.Snap the fixture into the mounting clips. Confirm that the fixture is
securely mounted
Suspending Mounted
G
Turn on the power
3 2
Open the clips See A below Remove diffuser See B below Remove gear tray See C below
Affix gear tray to the housing
1inch
ON
OFF
These waterproof luminaires may be wall mounted (Above 4 ft from the ground)
or ceiling mounted, are IP66 rated, and are suitable for damp and wet location
applications,as well as all indoor applications
2.If wall mounted,suitable for mounting within 4 ft of the ground

VM5 Lighting Solutions
INSTALLATION INSTRUCTION
Features:
Product name: Vapor Tight
IP66 Rated
Suitable for Damp & Wet locations,All Indoor Applications
Operating voltage: AC 120-277 50/60HzV
Driver: Meanwell driver
LED Type:Samsung 5630
Technical data:
Model Power L(inch) W(inch) H(inch) LF(inch)
MVT-40-38-C
MVT-40-38-F
MVT-50-38-C
MVT-50-38-F
MVT-40-48-C
MVT-40-48-F
MVT-50-48-C
MVT-50-48-F
MVT-50-75-C
MVT-50-75-F
38W
48W
75W
4.7 4.3
45.7
61.4
30
43
LF
4.7 4.3
Safety Notice:
1.Electrical installation should be performed by a licensed electrican only
2.Disconnect the luminaire from the power supply and let cool down before any
maintenance is performed.All maintenance should be performed by a
lisensed electrician only!
3.Never touch the LED’s while luminaire is energized
4.Please contact your local representative for more information
1
13100 Alondra Blvd.,#106,Cerritos,CA
90703 Email:[e-mail]
Toll Free:844.VM5.Light
ON-OFF Function:
Introduction:
Automatic switching based on motion and light level.
Operating voltage 120~277Vac, 50/60Hz
Rated load
120V AC: 200W(inductive), 400W (resistive),
220-240V AC:
HF system 5.8GHz±75MHz, ISM wave band
Transmitting power <0.5mW
Power consumption ≤0.5W(standby), <1W(operation)
Detection zone Max.(D x H): 10m x 6m
Detection sensitivity 25% / 50% / 100%
Hold time 5s / 1min / 5min / 15min / 30min
Daylight sensor 5lux / 10lux / 20lux / 30lux / 50lux /Disable
Mounting height 8m Max.
Motion detection 0.5~3m/s
Detection angle 150°(wall installation)
360°(ceiling installation)
Operating temperature -20℃~50℃
IP rating IP20
400W(inductive), 800W (resistive)
277V AC: 400W(inductive), 800W (resistive)
Setting
By selecting the combination on the DIP switch,sensor data can be precisely set for
each specific application.
123
5S
1min
5min
15min
30min
5lux
1234
10lux
20lux
30lux
50lux
Disable
100%
50%
25%
Detection area
Detection area can be reduced by selecting the combination on the
DIP switches to fit precisely each application.
Hold time
Refers to the time period the lamp remains at 100% illumination after
no motion detected.
Daylight sensor
The sensor can be set to only allow the lamp to illuminate below a
defined ambient brightness threshold.
When set to Disable mode, the daylight sensor will switch on the lamp
when motion is detected regardless of ambient light level.
4
This is an
and switch off after a hold time when there is no motion detected. Aa built-in
daylight sensor can read brightness value, the sensor does not switch on the
light if with sufficient natural light.
innovative motion sensor, switch on the light on detection of movement,