vo-water duomatik evoline User manual

INSTALLATION GUIDE
soft duomatik
evoline
Before introduction of the softener the installation guide has to be read carefully.
For any disturbances cause by disregarding the instructions evo-water doesn’t accept liability.
evo-water oHG
Falkenstraße 2 72589 Westerheim
Tel.: [phone]
Fax : [phone]
www.evo-water.com
[e-mail]

Safety instructions:
1. Before installation the softener:
Please refer to the corresponding installation –and operation
instructions in this manual.
2. Please refer to the local installation regulations and the general
directives, in particular DIN 1988 and EN1717, also the valid accident
prevention regulations.
3. With not designated use and improper service the manufacturer is
released from any liability.
4. Before the installation please check the statics of the walls, covers and
grounds for loading capacity.
According to place of action a backflow must be installed
corresponding to local regulation before the arrangement.
For the protection of the central tax valves from rust, sand etc. a
suitable mudflap or fine filter should be inserted before the
arrangement. The filter pad of the fine filters should be exchanged
according to DINAR / DVGW at a distance of 6 months or after soiling.
Please ensure that no water damages are caused (e.g., by ground
expiry). The manufacturer is not liable for water damages.
The food water of the arrangement must correspond to the information
of the German drinking water order.
The room temperature must be at least 7°C and may not cross 50°C.
5. Changes in the system may not be made without consultation and
approval with evo-water oHG, for damages no other guarantee is
taken over.
6. The system serves exclusively for the removing of undesirable mineral
substances which retreat as a scale. It serves as a pure system
protection.

1. Parts:
1.
BYPASS
8.
BLENDING REGULATOR
2.
VALVE HOUSING
9.
HARDNESS REGULATOR
3.
RESIN TANK
10.
TO BRINE VALVE
4.
CONTAINER FOR DEVICE AND SALT
11.
CONNECTIONS (1/2",3/4”, 1")
5.
BRINE VALVE (float)
12.
TO DRAIN
6.
WATER INLET
13.
COMMUNICATION TUBES
7.
WATER OUTLET
14.
TUBES TO BRINE VALVE

2. Precautions:
Make sure you have all necessary tools on hand before you begin with the
installation.
Follow all local legal regulations.
Read this manual carefully. If you have any questions or remarks, please
contact your evo-water supplier.
Check incoming pressure: minimum 1 bar (dynamic), maximum 8 bar (static)
(15 PSI –116 PSI). If necessary reduce incoming pressure.
Do not install the evo-water softener close to a heating source (environment
temperature must be below 40°C).
Protect softener and drain (12) against frost.
Make sure you have the latest installation manual at hand. Check with your
evo-water supplier.
3. Installation:
3.1 Close main valve and make sure pressure is released from piping. This can be
done by opening at least one tap.
3.2 Connect the two units by means of the provided Y-pieces. You can find them in
the salt compartment. The Y-piece with the filter inside, needs to be mounted
at the inlet of the valve. (= bottom connection) The other must be mounted at
the other connection.
First connect the Y-piece to one unit and afterwards to the other unit. Secure
them with the provided clips (4 pieces). You don’t need to take the units out of
the container to do this.

3.3 Check if all communication tubes are connected correctly.
See picture below: the two quick-release couplings marked with a green dot
should be connected by a communication tube (Ø4mm); the same should be
done for the two couplings marked with a blue dot.
3.4 C
u
t
o
p
e
n
m
a
i
n
w
a
t
e
r supply in order to install direct connections to the evo-water Softener or to
install the evo-water Bypass (recommended). Follow the arrows on both Bypass
and softener for water inlet and outlet.
Pay attention that the inlet filter doesn’t fall out.
3.4.1
with evo-water bypass with direct connections
The evo-water Bypass has a ¾” connection. The direct connections on the
water softener are available in ½”, ¾” and 1”.

Caution: before installing the softener, set
the Bypass in “bypass” mode, not in
“service”.
3.4.2
Connect both drain outlets (#12) to a
local drain by means of the provided
13mm flexible drain pipe. (through a
free flow off) In order to guarantee
that the device will keep on functioning
perfectly in the future, this drain pipe is
spirally reinforced to avoid later
blocking and/or kinks.
It is possible that both drains are
connected with each other through a
Y-piece. In this case, connect the Y-
piece to the local drain.
Please protect the drain against frost
and heat (min. temp. 5°C, max. temp.
40°C).
When another drain pipe is used, the guarantee on the unit is expired.
CAUTION: For the installation of the flexible drain hose to the fixed piping,
please follow local legislation.
maximum height and distance of flexible drain hose

3.5 Make sure to install the supplied overflow tap.
First, pierce a hole (Ø21mm) in the side wall of the container. For the positions
of the hole, there are two markings at the back of the container. They are
situated around 15cm from the top of the container. (see figure below) Once
the hole has been drilled, mount the overflow tap and secure it with the
supplied nut. After drilling, remove all bits of plastic that have fallen into the
container. A separate instruction leaflet with detailed information has been
added to the device.
3.6 Check if the brine valve is mounted correctly. This brine valve is mounted in the
brine tube and it must sit all the way at the bottom, with the right side up. (see
figure below) In order to check this, you need to remove the cover from the
brine tube.

3.7 Verify if the brine valve is connected to
the softener in the right way. The black
tube Ø4mm comes from the brine valve,
through the hole in the brine pipe and is
then connected with the small T-piece.
This T-piece connects the two pieces of
brine tube that come from both units.
Make sure that all tubes are fitted in the
connections as far as possible. Check if
there are no kinks in the tube and that
the tube is not squeezed together.
Pay attention:
Watch carefully that
you don’t squeeze the
tube when opening or
closing the tilt drawer
for the salt.
4. Settings:
4.1 Hardness regulator:
=part number 9 on the illustration on page 2
Measure the hardness of incoming
water by means of a hardness test
kit (not supplied by evo-water). evo-
water uses ppm settings of CaCO3.
(10 ppm CaCO3= 1°fh) (1°dh =
1,78°fh)
Adjust the hardness regulator to the
measured value. This requires a hex
key number 5.
Remark: always set regulator on
both units to the same setting.

4.2 Blending regulator:
= part number 8 on the illustration on page 2
With the blending regulator, you can
determine the outgoing hardness.
Depending on the desired residual
hardness, set outgoing hardness
with a hex key number 5. The
setting is proportional, i.e. 1/10 –
1/5 –1/… of total incoming
hardness.
Remark: always set regulator on both units to the same setting.
5. Start up:
5.1 Leave Bypass in “bypass” mode, open main valve and flush for several minutes
in order to avoid impurities from entering the softener. When you do not use a
Bypass, open the main valve slowly as described in 5.4.
5.2 Fill salt container with salt in the
provided space. Do not put salt
tablets in the compartment where
the softener is installed. Use only
specific salt tablets that are
suitable for softeners.
5.3 Add water in the salt container until the water
level is approx. 10cm 4” high. (the float on the
brine valve must be afloat)

5.4 Turn the bypass slowly to “service” mode. Open the main valve when you do
not use a Bypass.
5.5 Open a tap behind the softener so a flow runs through it. Some air may flow
from the tap; this comes from the softener. This will happen only once; at
start-up. Once only water flows from the tap, and no more air, close the tap.
5.6 Perform a manual regeneration.
5.6.1
Choose one of both units to perform a manual regeneration. Use a hex key
number 5 to turn the program disk (PRG) manually.
Turn PRG counter clockwise until it is in above position. When the arrow and
the small line on the transparent cover reach the area marked by “B”

(brining), the regeneration will start. Immediately, the PRG will drop down a
little (you will be able to see and hear this). “R” stands for refill (refilling the
container with water at the end of the regeneration stage). To make sure the
softener is in regeneration, there should be a small water flow to the drain,
and the water level in the container should drop.
5.6.2
Let regeneration perform until it stops automatically. The estimated time is
approx. 12 minutes. When regeneration has stopped, no more water flows to
the drain. This is a clear indication that the regeneration stage is over.
5.6.3
Open a tap behind the softener for several minutes to allow residual water to
be flushed from the tubing.
5.6.4
Check outgoing hardness with a “hardness test kit” (not supplied by evo-
water). Adjust blending if necessary.
5.7 Put the cover on to the container. Before you do this, make sure that the tilt
drawer for the salt is closed.
Do not forget to connect the overflow
with a drain.

5.8 Refilling salt.
To refill the container with salt, you don’t need to remove the cover. Just pull
the tilt drawer, so that it tilts out of the container. If you pull out the drawer far
enough it will stay fixed in the open position. In this position you can easily
refill the drawer with salt tablets.
When you are done refilling the salt, just lift the cover a little bit and push the
tilt drawer back in the container. If the drawer is back in its position, the cover
fits back on the container.
Pay attention:
Watch carefully that you don’t squeeze the tube
when opening or closing the tilt drawer for the
salt.

REMARKS:
It is recommended that a water softener is installed by a professional. Although the softener
is probably the easiest and safest softener on the market, it is imperative that all necessary
precautions are taken and local legislation is followed.
This installation guide is written to help the professional installer keeping in mind that this
person has essential knowledge about hydraulic softeners and domestic plumbing.
Proper working of the softener will be determined by proper installation.
An annual control of your Softener will guarantee optimal functioning and a long operating
life.
The EVO-WATER OHG is proud of its achievement in having provided in what we
believe to be the best softener available today.
Moreover, we are proud to have you as a customer. We will do our utmost to
deserve your trust.
evo-water oHG
Falkenstraße 2, 72589 Westerheim
Tel.: [phone]
Fax : [phone]
[e-mail]
www.evo-water.com