VOGELS PFW 6875 User manual

PFW 6875
www.vogels.com | Europe [phone]
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

Included Components
Required for installation
PFW 6875 Maximum Flat Panel Weight:
160 lb. / 72.57 kg.
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
www.vogels.com | Europe [phone]
5/16” x 3” (76mm) Lag Bolts
(Qty 4)
Thread Depth Indicator
(Qty 1)
Universal Spacers
(Qty 8)
5/16” (7.93 mm) Concrete
Wedge Anchors
(Qty 4)
5/16” Flat Washers
(Qty 4)
Universal Washers
(Qty 4)
Pencil Protective Eyewear
Electronic Stud Finder M6 or 1/4” Drill Bit M8 or 5/16” Concrete Drill Bit
Portable Drill
Phillips Head Screwdriver Socket Wrench
13mm or 1/2” Socket10mm Socket
Level
M5 Allen Driver
(Qty 1)
M4 x 12mm (Qty 4)
M4 x 16mm (Qty 4)
M4 x 25mm (Qty 4)
M6 x 12mm (Qty 4)
M6 x 16mm (Qty 4)
M6 x 25mm (Qty 4)
M8 x 12mm (Qty 4)
M8 x 16mm (Qty 4)
M8 x 25mm (Qty 4)
Wall Mount
(Qty 1)
Extension Brackets
(Qty 2)
Bracket
(Qty 1 Pair)
M8 Washers
(Qty 4)
M8 Nylon Nut
(Qty 4)
Page 2

PFW 6875
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
www.vogels.com | Europe [phone]
1
3
2
4
XX
1) Use a stud nder to determine the wall studs in the
vicinity of the mount.
2) Use a pencil to mark each of the wall studs.
Wood Stud Installation
Use a pencil to mark the upper right mounting location of the wall
stud.
Drill a “pilot hole” using a M6 or 1/4” drill bit on the stud that was
marked on the upper right.
1) Place the mount against the wall and align it with the pilot hole.
2) Insert one (1) 5/16” x 3” (76 mm) lag bolt one (1) 5/16” washer
into the upper right pilot hole.
3) Use a socket wrench and a 13mm or 1/2” socket to tighten the
lag bolt.
Page 3

PFW 6875
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
www.vogels.com | Europe [phone]
5
7
6
1) Level the mount
2) Use a pencil to mark the remaining three (3) mounting locations
1) Insert one (1) 5/16” x 3” (76 mm) lag bolt and one (1) 5/16” washer
into each pilot hole.
2) Tighten all lag bolts using a socket wrench and 13mm or 1/2” socket.
Do not over tighten the lag bolts
Drill a “pilot hole” in each of the three (3) marks with a power drill and
a M6 or 1/4” drill bit.
Page 4

PFW 6875
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
www.vogels.com | Europe [phone]
10
9
8
11
Two people recommended for this step; one person to level the
mount and another person to mark the mounting locations.
Drill a “pilot hole” in each of the four (4) mark areas with a M8 or
5/16” concrete drill bit.
1) Place the mount against the wall over the threaded shafts of the
concrete wedge anchors.
2) Attach the nuts and washers you remove and add (1) 5/16”
washers on each threaded shafts.
3) Tighten using a socket wrench and a 10mm socket.
Do not over tighten the concrete wedge anchor
1) Insert the concrete wedge anchors into each hole. Lightly tap
each concrete wedge anchors into place with a hammer.
2) Remove the nuts and washers from the concrete wedge anchors.
Concrete Wall Installation
5/16” Washer
Page 5

PFW 6875
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
www.vogels.com | Europe [phone]
PFW 6875 dedicated at-panel spacers are engineered with the knowledge
that aligning each at-panel on a large wall is time consuming and costly.
These model-specic spacers are available for most at-panels, which
signicantly reduces the installation time. (Call Customer Service to inquire
about model specic spacers.)
Installing OPTIONAL Model Specic Spacers
This spacer is shown for illustration purposes only. Your spacer may
look different depending on the display model you are installing.
1) Once your PFW 6875 is mounted in the desired location and
is level, align your spacer to the top left or right (depending on
your install direction) corner register tabs of your mount.
You may use commercially available hardware to secure the
spacer to the wall during installation (depending on the wall material).
You may utilize the same spacer for multiple PFW 6875 installations.
Start
Multiple PFW 6875 mounts can be installed using model specic spacers. Simply
repeat step one when installing each of the surrounding PFW 6875 mounts. Use
one spacer for each 2x2 installation by mounting it to the wall, or utilize the same
spacer as many times needed to complete an unlimited PFW 6875 large matrix
video wall.
1. Make sure the spacer is plumb and level and mark each corner where the
PFW 6875 will be mounted (or secure to the wall). It is best to start from the
bottom corner and work your way up.
2. Install the second mount working in a horizontal direction.
3. Ensure that the mount remains plumb and level.
4. Repeat this step for each mount horizontally
5. To install multiple rows, place spacer between previously installed
PFW 6875’s on the bottom row. Make sure the spacer is plumb and level,
mark the corners (or secure to the wall) to be sure of where the PFW 6875
should be and secure your mount to the wall.
Page 6
12
13
13

PFW 6875
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
www.vogels.com | Europe [phone]
1) Insert a small straw or toothpick into the threaded inserts found on the back
of the at-panel.
2) Use a pencil to mark the depth of the threaded insert on the small straw or
toothpick.
3) Mark the straw or toothpick 1/8” (3.175 mm) above the depth of the threaded
insert, as shown in Figure 1.
4) Insert the small straw or toothpick into the remaining threaded inserts to
compare and verify their depth using the straw or toothpick’s 1/8” (3.175 mm)
allowance mark.
5) Locate the correct diameter screw for the threaded insert.
If the screw you selected is longer than the 1/8” (3.175 mm) allowance
mark on the small straw or toothpick, as shown in Figure 2 and Figure 3,
do not use this screw. The screw length must not bypass the mark.
6) Test each size of the screws provided.
The correct screws should thread easily into themounting point and not pull
out when tension is applied.
Small Straw or Toothpick
Marking the 1/8”
Allowance
Small Straw
or Toothpick
Small Straw
or Toothpick Depth Plus 1/8” Allowance
Mark
Depth Plus 1/8” Allowance
Mark
Selecting the Mounting Hardware
Securing the Adapters
Optional adapters are available with your PFW 6875 mount.
Secure the adapters to the PFW 6875 brackets with the
supplied M8 washers and Nuts.
M8 Nylon nut
M8 Washer
Page 7

PFW 6875
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
www.vogels.com | Europe [phone]
Universal Washer Installation
Universal Spacer Installation
Flat Panel
Universal Washer
Universal Spacer
Mounting Bracket
Mount Point
Mounting Screw
1˝ ¼˝
The Universal Spacers
Fit M4, M5, M6 and M8 screw sizes.
Universal Washers are designed to accommodate the various M4, M5, M6 and
M8 hole sizes required by at-panels.
Do not place excessive pressure on the back of the at-panel, as this
may damage your at-panel.
The Universal Washer must be installed between the head of the
mounting screw and the mounting bracket as shown.
Does your at-panel have:
●Recessed mount points?
●Uneven mount points?
●A curved back?
●Any obstruction near the mount point?
If Yes, you must install Universal Spacers. Remove the mounting brackets,
Universal Washers, and mounting screws from the back of the at-panel.
Proceed to the “Universal Spacer Installation” section.
If No, skip to the “Attaching the Mounting Bracket to the Flat-Panel”
section.
M8
M5, M6
M4
25.4 mm 6.35 mm
Page 8
Universal Spacers allow you to attach the mounting bracket to at-panels which
have recessed or uneven mount points. Each Universal Spacer adds 1/4” (6.35 mm)
to the distance between the mounting bracket and your at-panel.
The Universal Spacers must be stacked and oriented as shown.
The Universal Spacers must only be installed between the mounting bracket
and your at-panel.

PFW 6875
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
www.vogels.com | Europe [phone]
Attaching the Mount Bracket to the Flat-Panel
Mounting bracket adjustments are factory pre-set (see Note).
This section requires two people.
Do not release your at-panel until you are certain that top and
bottom hooks of both mounting brackets are securely seated
on the upper and lower mounting rails of the wall panel.
1) Raise the at-panel past the top and bottom mounting rails on the
wall panel.
2) Slide the at-panel down slowly, keeping it close to the wall.
3) Engage the top and bottom mounting brackets to the rails of the
mount.
Note: These registers must
align prior to installation.
They are factory set.
Check to determine proper
alignment
Attaching the Flat-Panel to the Mount
Page 9
1) Place your at-panel screen-side down on a soft, at surface.
2) Identify the number and location of the thread inserts on the back of your
at-panel.
3) Aligning the holes on each mounting bracket with the thread inserts on the
back of your at-panel.
4) Secure each mounting bracket to your at-panel by inserting a minimum of
two (2) screws per bracket.
Do not overtighten the mounting hardware.

PFW 6875
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
www.vogels.com | Europe [phone]
Move Inward
Left Control Right Control
Move Outward
Left Control Right Control
The locking safety screws keep the at-panel from being
accidently dislodged from the PFW 6875.
1) Locate the pre-installed security locking safety screw at the bottom
of each of the mounting brackets.
2) Use the M5 Allen driver (supplied) to tighten the locking safety
screw.
Locking Safety Screw Installation
Do not overtighten the locking safety screws.
Note: Tighten screw to surface, then tighten 1/4” (6.35 mm) turn
Pre-installed
Locking Safety Screw
( 1 per Bracket )
Page 10