VOGELS PLW 1001 User manual

PLW 1001 - 1x2 LED video wall mountL
MOUIN_PLW 1001 _V02
EN
DE Montageanleitung
FR
NL
ES
IT
PT Manual de montagem
EL Οδηγίες συναρμογής
SV
PL
RU Инструкция по сборке и установке
CZE Návod k montáži
SK Návod na montáž
HU Szerelési előírás
TR Montaj kılavuzu
RO
UK Вказівки по монтажі
BG Инструкции за монтаж
JA 設置の説明書
ZH

1) Find your desired mounting location.
2) Drill the 5/16” x 3” lag bolt with washer into
the wall (C + D)
Do not fully drill 5/16” x 3” lag bolt into the
wall. Leave 25 mm [1” inch] out.
Wall Mount
x1
Wall Plate M5 x 6 mm Flat Head
Screw
M5 x 10 mm Screw M4 x 6 mm Set Screw
Spacer Bracket
1/4” x 2 1/2”
Push Pin
M6 x 20 mm
Socket Cap
5/16” x 3” Lag
Bolt
M5 Allen Key M2 Allen Key
5/8”-10 x 2” Bolt
with hole
5/16” x 6” Lag Bolt 5/16” Washer
x4 x8
x2
x4 x4 x5
x1
x4 x8
x8
x1
x1 x1
1200
47.25
600.2
23.63
[PRE-HANG
MOUNTING]
1348.7
53.10
1311.4
51.63
TO DETERMINE THE POSITION OF THE PRE-HANGER SCREW
FIRST MEASURE THE DISTANCE REQUIRED FROM THE FLOOR
TO THE BOTTOM EDGE OF THE FRAME AND ADD 1311.4 mm [51.63"]
SECTION
CONNECTOR
PLATE
(FLOOR LINE)
5/32” Allen Key
x1
M6 x 16 mm Flat
Socket Head Screw
x4
Page 2
A B CD
EFGH
IJKL
MNO
1

Place the wall mount over the lag bolt through
the key slot hole.
Key Slot
2
3
4
1) Extend the mount.
2) Install the 1/4” x 2 1/2” push pin (F) to keep the mount extended.
Lag Bolt
Washer
Install the four (4) 5/8”-10 x 2” Bolt (A) with hole into the
wall mount. Flush all threads to edge.
Flush Bolt
Page 3

1) Level the wall mount.
2) Place the wall bracket (I) between the wall mount and wall.
3) Secure the mount into the wall using four (4) 5/16” x 6” lag
bolts (B) and four (4) 5/16” washers (C) into the 5/8”-10 x 2” Bolt
with hole.
Before installing the
5/16” x 6” lag bolt and
washer make sure the
phillips screw is in the
center of the slots.
This will give 1/2”
adjustments either up
or down.
Wall Plate
Washer
5/16” x 6” Lag Bolt
In / OutAdjustments
Uneven wall surfaces can be adjust by
turning the 5/8”-10 x 2 Bolt with hole.
Up / Down
Page 4
5
6

7
8
1
2
Page 5
1) Use four (4) M6 x 16 mm flat socket head screws (N) on the first
2) Install second LED display using four (4) M6 x 20 mm
LED display to center it in place.
4) Install the LED displays in the following order as shown above.
socket cap screws (E).
3) Optional to change the M6 x 16 mm flat socket head screws (N) to
M6 x 20 mm socket cap screws (E).

9
10
1
1350 mm
[ 53.15” ]
Linear Set Up
OPTIONAl EXTENSIONS
Page 6
Install eight (8) M4 x 6 mm set screws (L). You can adjust the panel in & out by using the M2 Allen Key (H).

Align the tabs with eachother.
11
12
Page 7
Install the spacer brackets (M) to the mount using eight (8) M5 x 6 mm flat head screws (J). Four (4) screws per bracket.

1
1
Install the mounts together using two
(2) M5 x 10 mm screws (K).
To collapse the mount and secure, remove the push pin than
install two (2) M5 x 10 mm screws (K). One screw per latch.
Adjustments
See steps 6 and 9.
Page 8
(GB) Subject to printing errors and technical amendments.
(NL) Drukfouten en technische wijzigingen voorbehouden.
(F) Sous réserve de fautes d’impression et de modi cations techniques.
(D) Für Druckfehler übernehmen wir keine Verantwortung.Technische
Änderungen vorbehalten.
(E) Reservados errores de imprenta y sujete a modi cationes.
(I) Con riserva di modi che techniche e di eventueli errori di stampa.
(P) Reserva-se a ocorrência de gralhas e de modi técnicas.
(H) Nyomdahibák és technikai változtatások joga fenntartva.
(PL) Zastrzega się możliwość występowania błędów drukarskich i zmian technicznych.
(RUS) Vozmoøny oπibki pri pehati i texniheskie mod acii.
Designed and engineered in the Netherlands
More information on: www.vogels.com
VOGEL’S PRODUCTS BV, HONDSRUGLAAN 93,5628 DB EINDHOVEN,THE NETHERLANDS
13
14