VOGELS PLW 1003 User manual

MOUIN_PLW 1003 _V02
PLW 1003 - 1x3 LED video wall mount
EN
DE Montageanleitung
FR
NL
ES
IT
PT Manual de montagem
EL Οδηγίες συναρμογής
SV
PL
RU Инструкция по сборке и установке
CZE Návod k montáži
SK Návod na montáž
HU Szerelési előírás
TR Montaj kılavuzu
RO
UK Вказівки по монтажі
BG Инструкции за монтаж
JA 設置の説明書
ZH

1) Find your desired mounting location.
2) Drill the 5/16” x 3” lag bolt (D) with washer (C) into
the wall
Do not fully drill 5/16” x 3” lag bolt into the
wall. Leave 25 mm [1” inch] out.
Wall Mount
x1
Wall Plate M5 x 6 mm Flat Head
Screw
M5 x 10 mm Screw M4 x 6 mm Set Screw
5/32” Allen Key
Spacer Bracket
1/4” x 2 1/2”
Push Pin
M6 x 20mm
Socket Cap
5/16” x 3” Lag
Bolt
M5 Allen Key M2 Allen Key
5/8”-10 x 2” Bolt
with hole
5/16” x 6” Lag Bolt 5/16” Washer
x4 x8
x2
x4 x4 x5
x1
x6 x12
x1
x12
x1
x1 x1
2025
[79.73]
1200
[47.24]
1986.41
[78.20]
FOR SUPPORT SCREW LOCATION,
DESIRED DISTANCE FROM
FLOOR PLUS 1986.4 mm.
M6 x 16 mm Flat
Socket Head
M8 x 70 mm Screw
2x4x
Page 2
A
K
J
I
H
G
F
E
D
C
B
L
MNOP
1

Place the wall mount over the lag bolt through
the key slot hole.
Key Slot
1) Extend the mount.
2) Install the 1/4” x 2 1/2” push pin (F) to keep the mount extended.
Lag Bolt
Washer
Install the four (4) 5/8”-10 x 2” Bolt (A) with hole into the
wall mount. Flush all threads to edge.
Flush Bolt
Page 3
2
3
4

1) Level the wall mount.
2) Place the wall bracket (M) between the wall mount and wall.
3) Secure the mount into the wall using four (4) 5/16” x 6” lag
bolts (B) and four (4) 5/16” washers (C) into the 5/8”-10“ bolt (A)
with hole.
Before installing the
5/16” x 6” lag bolt and
washer make sure the
phillips screw is in the
center of the slots.
This will give 1/2”
adjustments either up
or down.
Wall Plate
Washer
5/16” x 6” Lag Bolt
In / OutAdjustments
Uneven wall surfaces can be adjust by
turning the 5/8”-10 x 2 Bolt (A) with hole.
Up / Down
Page 4
6
5

1
2
3
Page 5
1) Use four (4) M6 x 16 mm flat socket head screws (N) on the
first LED display to center it in place.
2) Install the second and third LED display unsing four (4)
M6 x 20 mm socket cap screw in each LED display (E).
3) Optional to change the M6 x 16 mm flat socket head
screws (N) to M6 x 20 mm socket cap screws E).
4) Install the LED panels in the following order as shown above.
7
8

9
Install twelve (12) M4 x 6 mm set screws (L). You can adjust the panel in & out by using the M2 Allen key (H)..
1200 mm
[47.24”]
Linear Set Up
OPTIONAL EXTENSIONS
Page 6
10

Align the tabs with eachother.
Page 7
Install the spacer brackets (M) to the mount using eight (8) 6 mm flat head screws (J). Four (4) screws per bracket.
11
12

Install the mounts together using
four (4) M5 x 10 mm screws (K) and two
(2) M8 x70 mm screws (O).
To collapse the mount and secure, remove the push pin than
install two (2) M5 x 10 mm screws (K). One screw per latch.
Adjustments
See steps 6 and 9.
Page 8
(GB) Subject to printing errors and technical amendments.
(NL) Drukfouten en technische wijzigingen voorbehouden.
(F) Sous réserve de fautes d’impression et de modi cations techniques.
(D) Für Druckfehler übernehmen wir keine Verantwortung.Technische
Änderungen vorbehalten.
(E) Reservados errores de imprenta y sujete a modi cationes.
(I) Con riserva di modi che techniche e di eventueli errori di stampa.
(P) Reserva-se a ocorrência de gralhas e de modi técnicas.
(H) Nyomdahibák és technikai változtatások joga fenntartva.
(PL) Zastrzega się możliwość występowania błędów drukarskich i zmian technicznych.
(RUS) Vozmoøny oπibki pri pehati i texniheskie mod acii.
Designed and engineered in the Netherlands
More information on: www.vogels.com
VOGEL’S PRODUCTS BV, HONDSRUGLAAN 93,5628 DB EINDHOVEN,THE NETHERLANDS
13
14