Vogue 310602 Wiring diagram

VOGUE 9 Function Pyrolytic Wall Oven
600mm BLACK
To prevent the risk of accidents or damage to the appliance, it is essential
to read these instructions before it is installed and used for the first time
310602
INSTALLATION
INSTRUCTIONS
USER GUIDE

Contents
1…………………………………..…………………Important safety information
5…………………………………..…………………Installation
7…………………………………..……………..….Prior to start up of the appliance
7..…………………………………..……………….Your new oven
10………………………………..………………….Program and function instruction
18…………………………………..……………….Settings & functions of the oven
19…………………………………..……………….Before using the oven for the first time
20…………………………………..……………….How to operate the oven
20…………………………………..……………….Troubleshooting
21…………………………………..……………….Baking and grilling tips
23…………………………………..……………….Maintenance and cleaning
27…………………………………..……………….Environmental note
28…………………………………..……………….Test dishes

1
Important safety information
This User Instruction Manual contains important information, including safety &
installation points, which will enable you to get the most out of your appliance. Please
keep it in a safe place so that it is easily available for future reference; for you or any
person not familiar with the operation of the appliance.
Warning:
●The appliance and its accessible parts
become hot during use. Care should
be taken to avoid touching heating
elements.
●Children less than 8 years of age shall
be kept away unless continuously
supervised.
●This appliance can be used by children
aged from 8 years and above and
persons with reduced physical,
sensory or mental capabilities or lack
of experience and knowledge or they
have been given supervision or
instruction concerning use of the
appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
●A steam cleaner is not to be used.
●Accessible parts may become hot
during use. Young children should be
kept well away when in use.
●Do not use harsh abrasive cleaners or
metal scrapers to clean the oven door
glass as this can scratch the surface,
which may result in the oven glass
shattering.
●Do not use abrasive products to clean
the glass door panel to avoid
scratching it. Otherwise, severe failure
might happen to the appliance.
●The appliance must not be installed
behind a decorative door in order to
avoid overheating.
●The air must not be discharged into a
flue that is used for exhausting fumes
from appliances burning gas or other
fuels.
Operation:
Warning! Danger of fire!
●Do not allow paper or cloth to come in
contact with any heating element.
●Never store or use corrosive
chemicals, vapors, flammables or
nonfood products in or near oven. It is
specifically designed for use when
heating or cooking food. The use of
corrosive chemicals in heating or
cleaning will damage the appliance
and could result in injury
●If food inside an oven should ignite,
keep door closed. Switch off the oven
and disconnect from supply power.
●Exercise caution when opening the
door. Standing to the side, open the
door slowly and slightly to let hot air
and/or steam escape. Keep your face
clear of the opening and make sure
there are no children or pets near the
oven. After the release of hot air
and/or steam, proceed with your
cooking. Keep doors closed at all
times unless necessary for cooking or
cleaning purposes.

2
●Only use utensils that are suitable for
use with ovens.
Warning!
Danger of explosion!
●Liquids and other foods must not be
heated in sealed containers since they
are liable to explode.
●If smoke is observed, switch off the
oven and keep the door closed in order
to stifle any flames.
●Do not allow any accessories or electric
cables to contact the hot parts of the
appliance.
Warning!
Hot surfaces! Risk of burns!
●During use the appliance becomes hot.
Care should be taken to avoid touching
heating elements inside the oven.
●Warning! Accessible parts may become
hot during use. Young children should
be kept away.
●Never move racks or pans when they
are hot. Wait until they cool.
Safety advice:
IMPORTANT!
Always switch off the electricity
supply at the mains during
installation and maintenance.
General Information
●This appliance is designed for domestic
household use and can be built into a
standard kitchen cabinet or housing
unit.
●The appliance surfaces will become hot
during use and retain heat after
operation.
●Any damage caused by the non-
compliance of temperature tolerance of
oven during installation or by the too
close distance between the furniture
and the oven will be borne by the
owner.
●This appliance is not intended for use
by persons (including children) with
reduced physical sensory, or mental
capabilities, or by those who lack
experience and knowledge, unless they
have been given supervision and
instruction concerning the use of the
appliance by a person responsible for
their safety .
Installation
●The oven must be installed in
accordance with the installation
instructions and all measurements must
be followed.
●All installation work must be carried out
by a competent person or qualified
electrician.
Children
●Please dispose of the packaging
material carefully. Packaging material
can be dangerous to children.
●Make sure to keep children away from
the appliance, children should be
supervised to ensure that they do not
play with the appliance. It might be
dangerous to allow the children to touch
the appliance.
●Under the pyrolytic self-cleaning mode,
the surfaces may get hotter than usual
and children should be kept away.
General Safety
●Do not place heavy objects on the oven
door or lean them on the oven door

3
when it is open, as it may cause
damages to the oven door hinges.
●Do not place those baked hot oil or fat
unattended on unattended areas, as it
will be a fire risk.
●Do not place pans or baking trays
directly on the base of the oven cavity,
even if aluminum foil is placed below
them.
●Do not allow cable or plug to come into
contact with the heating areas of
appliance.
●Do not install the appliance next to
curtains or soft furnishings.
●Do not attempt to lift or move cooking
appliances by using the oven door or
handle, as this may cause damage to
the appliance or result in injury to the
person lifting the appliance.
Electrical safety
●If the supply cord is damaged, it must
be replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid a hazard.
●The appliance must be placed in such a
way, that the power supply is
accessible at all times.
●Before connecting the appliance to the
power supply, check that the power
supply voltage and current rating
corresponds with the power supply
details shown on the appliance rating
label.
●Never use a damaged appliance!
Disconnect the appliance from the
power source and contact your supplier
if it is damaged.
●Danger of electric shock! Do not attempt
to repair the appliance yourself. In case
of malfunction, repairs are to be
conducted by qualified personnel only.
●To avoid damaging the cord, do not
squeeze, bend or chafe it on sharp
edges. Keep it away from hot surfaces
and open flames as well.
●Lay out the cord in such a way that no
unintentional pulling or tripping over it is
possible.
●Do not open the appliance casing under
any circumstances. Do not insert any
foreign objects into the inside of the
casing.
●Never use accessories which are not
recommended by the manufacturer.
They could pose a safety risk to the
user and might damage the appliance.
Only use original parts and
accessories.
●Keep the appliance away from any hot
surfaces and open flames. Always
operate the appliance on a level, stable,
clean and dry surface. Protect the
appliance against heat, dust, direct
sunlight, moisture, dripping and
splashing water.
●Do not place objects with open flames,
e.g. candles, on top of or beside the
appliance.
●WARNING: Ensure that the appliance is
switched off before replacing the lamp
to avoid the possibility of electric shock.
●The fixed wiring for applicant shall have
an all-pole disconnection device.
●Disconnection incorporated in the fixed
wiring is in accordance with AS/NZS
3000.
Safety:
●Attention, the glass is extremely fragile.
Always wear gloves when handling.
●For your safety, this product is made of
tempered glass. This type of glass is
highly resistant but has the feature to
retain the "memory" of shocks.
●Therefore, it should handle the product
with the greatest care to avoid shocks
and twists, especially during
installation.

4
●Avoid installing this type of product in
areas where it would be highly exposed
to shocks.
●Do not let children play with the product.
●Do not stick adhesive film on the glass
surface. In case of breakage, it would
generate large pieces that could be
dangerous
Electrical connection
Danger of electric shock!
●Any electrical installation must be
carried out by an authorised
professional.
●All fittings must be installed by a
competent person in accordance with
local regulations. If in doubt, consult a
qualified electrician.
●Important! Always switch off the
electricity supply at the mains during
installation and maintenance. We
recommend that the fuse is withdrawn
or circuit breaker switched off at the
distribution board whilst work is in
progress.
●This product must be earthed – if no
earth feed wire is available, consult an
electrician.
●Means for disconnection must be
incorporated in the fixed wiring in
accordance with the wiring rules. To
achieve this install appropriate switched
fused connection unit.
●Note! A switched fused connection unit
having a contact separation of at least
3mm in all poles should be connected
in fixed wiring.
●Connect the incoming positive, neutral
and earth cables to the terminals of the
switched fused connection unit. Ensure
connections are tight.
●The spur outlet must still be accessible
even when your oven is located in its
housing to enable the appliance to be
disconnected from the mains supply.
Cleaning
●Always disconnect the power supply
prior to cleaning the appliance. If the
switched fused connection unit is
difficult to reach, shut off the power
supply by using the corresponding
circuit breaker at the distribution board.
●Clean the appliance thoroughly before
first use. The oven should be cleaned
regularly and any food deposits
removed.
●Never clean the oven surfaces by steam
cleaning.
●The oven cavity should only be cleaned
with warm soapy water, using either a
sponge or soft cloth. No abrasive
cleaners should be used.
●Any stains that may appear on the
bottom of the oven will have originated
from food splashes or spilt food, these
splashes occur during the cooking
process. These could possibly be a
result of the food being cooked at an
excessively high temperature or being
placed in cookware that is too small.
●You should select a cooking
temperature and function that is
appropriate for the food that you are
cooking. You should also ensure that
the food is placed in an adequately
sized dish and that you use the drip tray
where appropriate.
●Excess spillage must be removed
before cleaning and take out all your
accessories.

5
Installation
Before installation
The appliance should be installed built in the cabinet . It should be keep safety distance with
appliance and the kitchen walls. Detail please check below picture . (values in mm).
•Surfaces, synthetic laminates and adhesives used must be heat resistant(100℃
minimum), and neighbouring unit fronts up to 70℃.
•Kitchen cabinets must be set level and fixed. A gap of 5 mm is required between the
appliance and surrounding unit fronts.
•If there is a drawer beneath the oven, a shelf must be installed between oven and
drawer.

6
Installation method
Installation and connection
▲Material damage!
The door and/or handle must not be used for lifting or moving the appliance.
•For installation the appliance must be connected in accordance with all local gas and/or
electrical regulations.
•Carry the appliance with at least two persons.
•Use the slots or wire handles located at both sides to move the appliance.
Connection to the mains supply
This appliance must be earthed!
•Our company shall not be held responsible for any damage caused by using the
appliance without an earthed socket. Risk of electric shock, short circuit or fire by
unprofessional installation! The appliance may be connected to the mains supply only
by an authorized qualified person and the appliance is only guaranteed after correct
installation.
•Risk of electric shock, short circuit or fire by damage of the mains lead! The mains lead
must not be clamped, bent or trapped or come into contact with hot parts of the
appliance. If the mains lead is damaged, it must be replaced by a qualified electrician.
•The mains supply must correspond to be data specified on the rating plate of the
appliance. The appliance mains cable must correspond to the specifications and the
power consumption.
Risk of electric shock!
Before starting any work on the electrical installation, please disconnect the
appliance from the mains supply.
Installation

7
1. Slide the oven through the cabinet aperture, align and secure.
2. Fix your oven with the 2 screws and washers as indicated in the figure.
Final check
1. Connect the appliance to the mains supply and switch on the mains supply.
2. Check function.
Prior to start up of the appliance
•Once this simple operation has been carried out the oven is ready to use for cooking.
•This appliance is exclusively for domestic use.
•Use the oven to cook food only.
•Before cooking, make sure all oven accessories that are not required are removed
from the oven.
•Pre-heat the oven to the cooking temperature before using it.
•Place the cooking trays in the center of oven and leave space in between when using
more than one, so that the air can circulate.
•Do not put oven trays on the base of the oven or cover it with aluminium foil. This will
cause thermal accumulation. The cooking and roasting times will not coincide and
the enamel may be damaged.
•Try to open the oven door as little as possible to see the food (the oven light remains
on during cooking).
•Take care when opening the door to avoid contact with hot parts and steam.
Your new oven
A. Oven overview

8
1. Control panel 4. Wire Rack
2. Fan motor (behind steel plate) 5. Door
3. Tray 6. Handle
B. Technical specifications
Voltage/frequency
220-240V
～
50Hz
Total power consumption
3150KW
Cable type/section
H05VV-F 3*1.5mm
2
Cable length
1.2m
External dimensions(height/width/depth) 595/595/593（mm）
Installation dimensions(height/width/depth) 600/600/ min 595（mm）
Main oven
Multifunction oven
Energy efficiency class
A
Oven lamp
25W/350°C
Grill power consumption
3050KW
C. Your accessories
•The accessories supplied with your appliance are suitable for making many meals.
Ensure that you always insert the accessories into the cooking compartment the right
way round.
•There is also a selection of optional accessories, with which you can improve on some
of your favourite dishes, or simply to make working with your oven more convenient.

9
Inserting accessories
You can insert the accessories into the cooking compartment at 5 different levels. Always
insert them as far as they will go so that the accessories do not touch the door panel.
The accessories can be pulled out approximately halfway until they lock in place. This
allows dishes to be removed easily.
Note: The accessories may deform when they become hot. Once they cool down again,
they regain their original shape. This does not affect their operation.
Oven tray
For moist cakes, pastries, frozen meals and large roasts. It can also be used to catch
dripping fat when you are grilling directly on the wire rack.
Wire rack
Used for roasting and for placing the food to be baked, roasted or cooked in casserole
dishes to the desired rack.

10
D. Control panel
Here, you will see an overview of the
control panel. Depending on the
appliance model, individual details may
differ.
1.3.1 Button icon instruction
Pic 1: Buttons diagram
1.3.2 Display section
Pic 2: Display screen icon
Display screen icon instruction
Icons
Function
Icons
Function
1
Function icon
8
Cooking end time setting icon
K1
K2
K3
K4
KB1
KB2
Reminder/parameter
switch
(temperature/time)
Clock/
reservation
Start
up
Pause/
cancel
Plus/minus
(cooking
function)
Plus/minus
(temperature/time)

11
2
Display the time value
9
Reservation function
3 Reminder time setting icon 10 Oven working icon
4 Reminder time icon
11
Display the temperature value
5
System time icon
12
Unit of degree Celsius
℃
6
System time setting icon
13
Lock function
7
Work parameter setting icon (time
and temperature)
1.3.3 Function icon instruction
Icon
Function
Icon
Function
Top outer heat element Top inner heat element
Heating fan (Defrost) Bottom heat element
Program and function instruction
1. Power on
Connect your appliance to the mains supply, all indicator lights of the display board will light
up for 1second and then enter the clock setting state. Default time show 12:00, hour “12”
flashes, the system clock setting icon “ ” flashes, and the system clock icon “ ” is always
on. The clock can be input at this time, refer to clock setting requirement for details.
•After 10 seconds without any operation and the oven will enter to adjust minute
automatically.
•Within 10 seconds without any operation when adjusting minute, the oven will enter
standby mode automatically.
•Under the standby mode, the display always shows system time.(Refer to picture 3 for
the display effect.)
Pic 3: Initial standby mode
When the oven is powered on, the oven door lock will start to self-inspection. During the
self-inspection, the door lock will run back and forth automatically. If there is no abnormal
alarm within 20 seconds, then self-inspection is completed. Or if it shows fault code “E-3”

12
during the self-inspection, please refer to protection function for problem analysis, you can
touch “ ” to cancel the fault code and return to standby mode.
2. Time setting
In the standby mode, touching the “ ” button once to enter the system clock setting state.
At this time, the hour value of the clock and the setting icon “ ” flash (1s/1 time) and the
hour is set by rotating the switch KB2. (0~23~0 is recyclable)
Pic 4: Hour and minute adjustment display effect
•After adjusting the hours, re-touch “ ” to switch to minute adjustment. Minute value and
the setting icon “ ” flash at this time, you can set minute time by rotating programming
switch KB2.(0~59~0 recyclable)
•After adjusting the minutes, re-touch the “ ” to confirm, clock setting accomplished.
And at this time, the clock setting icon “ ” goes out and the second icon “：”flashes
(1s/1 time).
•When the hour and minute are set, the system clock setting icon “ ” flashes and the
system clock icon “ ” is always on. After confirming, the setting icon “ ” is off and the
system clock icon “ ” continues to be displayed. In the hour setting, if you do not touch
the “ ” button to confirm within 10 seconds, it will automatically switch to the minute
setting. If the “ ” button is not confirmed within 10 seconds after the clock setting is
completed, the system defaults to complete the clock setting and automatically returns
to the standby state. If the clock is not set within 20 seconds after power-on, the system
default clock is 12:00 and enters standby state. If the power is turned off, the clock will
be reset.
•In the standby state, only the system clock is displayed.
3. The choices of function
•Under standby status, switch different functions by rotating the programming switch
KB1 in turn, refer to picture 5 for the order.(Non-recyclable, oven function will
remember the last operation)
Pic 5: Oven function mode
•When selecting the function, the clock position shows the default cooking time of the
corresponding function (it will show “Eco” under Eco mode), the temperature position
shows the default temperature of the corresponding function. For temperature
adjustable function mode, temperature place will display default temperature value of
corresponding function and flash, temperature icon “℃” will flash, and the working
parameter setting icon “ ” flash as well as the oven working icon “ ” is always on.

13
You can rotate the programming switch KB2 to set the cooking temperature. If
temperature is not adjustable for that function level, the default clock value and the
working parameter setting icon “ ” flash as well as the oven working icon “ ” is
always on.
•For temperature adjustable function mode, after the cooking temperature is set,
touch “ ” to switch to cooking time adjustment, display screen clock place will
display default cooking time of corresponding function and flash, the working
parameter setting icon “ ” flash and working time icon “ ” is always on, you can
rotate programming switch KB2 to set the cooking time at this time.
•For temperature is not adjustable function mode, you can set the cooking time
directly.
•Please refer to the above for detailed operation.
•If the cooking time and temperature are not set, or not touching “ ” within 10
seconds of completion, the system automatically returns to standby status. (The
cooking functions table are attached behind.)
•Under working status the oven displays as followings:
Pic 6: Working status display effect
•Oven display when working: “ ” cooking time icon will display, clock place will
display cooking countdown time, corresponding selection menu display, and the
temperature position displays the real-time cavity temperature.
Note:
(1) Normal function cooking time setting range is 0 minutes to 10 hours.
(2) When the cooking time is set to 0 minutes, if the button “ ” is touched at this time, the
oven will not work and the system will automatically return to the standby state.
(3) When the cooking time is set to 0 minutes, if the reservation function setting is
performed at this time, after setting the reservation time, touch the button “ ”, the oven
will not make a reservation, and the system will automatically return to the standby
state.
•When the cooking time or cooking temperature setting are finished, press“ ” button to
start the oven and corresponding icon stop flashing. After the oven starts working, the
cooking time begin to countdown by second.
•Cooking note: When cavity temperature is close to set temperature, oven will prompt for
2 seconds. If cooking time countdown to 0, oven will stop cooking (exhaust fan will
continue to work), and the system return to standby status automatically. Buzzer will
continuously prompt for 5 minutes(1s/time), exhaust fan will stop working after cavity
temperature is below 100℃.
•Temperature display range: not lower than 30℃, display Lo℃when lower than 30℃.

14
4. Reservation function
•After setting cooking time and temperature and before touching “ ” to start-up, touch
“” to enter to cooking end time(reservation function) setting (default end time=system
time +set cooking time), cooking end time icon “ ” will flash(1s/ time) , the reservation
function icon “ ” is always on and the hour value of the clock position flashes at this
time, rotating programming switch KB2 to set the hour. After the hour time setting is
completed, touch “ ” again to enter the minute time setting. At this time, the minute
value of clock position flashes, and the minute time can be set by rotating programming
switch KB2.(You can use the “ ” to switch hour and minute settings circularly. )After
cooking end time setting completed, touch “ ” to start, oven will enter reservation
status.
•The longest reservation time is 24 hours.
•Under reservation status the display screen will display as picture 7. All elements and
motors will not work at this time.
Pic 7: Reservation status display effect
•Reservation status display: “ ” reservation icon will display, “ ” system clock icon will
display, clock position will display system time, the selected menu will display,
temperature position will display setting or default cooking temperature.
•If more than 10 seconds not confirmed during setting reservation function, the oven will
automatically return to standby state.
•Under reservation status, you can touch “ ” to query the cooking start time (cooking
start time=cooking end time-cooking time) .
•If you need to cancel the reservation setting under reservation status, you can touch
“ ” to cancel it and oven will enter to standby mode.
5. Pyrolytic self-cleaning mode
•You can switch to pyrolytic self-cleaning mode by rotating programming switch KB1.
The default temperature of this mode is not adjustable, default working time is 1.5
hours. You can rotate KB2 to adjust the working time, adjustable working time range is
min. 1.5 hours and max. 2.5 hours.
•After selecting the pyrolytic self-cleaning mode and setting working time, touch “ ” to
start working. At this time, “ ” icon will display, door lock will be activated, door lock
icon “ ” will always display, indicating that the oven door has been locked and
pyrolytic self-cleaning mode starts, touch “ ” button can pause or cancel the function.
•After the self-cleaning function is confirmed and started, clock position shows working
countdown time, temperature position shows “ ”. Oven lamp cannot be used after
pyrolytic self-cleaning mode is activated.

15
•After start self-cleaning, door lock function will be activated automatically, the oven door
will be locked and self-cleaning process starts. After self-cleaning process starts, if the
display screen shows fault code “E-3”, please refer to protection function for problem
analysis. You can touch “ ” to cancel the fault code and return to standby mode. After
clear the fault code, reset self-cleaning function, and touch “ ” again to start.
6. Door lock function
6.1 Door lock display: When self-cleaning process is completed, oven will enter standby
mode. When oven cavity temperature is higher than 300℃,display screen will display door
lock icon “ ”(display effect refer to picture 8.) Door lock will be relieved automatically
when cavity temperature is lower than 280℃,door lock icon “ ” on the display screen will
extinguish at this time.(Refer to picture 9 for display effect.)
Pic 8: Door lock activated display effect under standby status
Pic 9: Door lock relieved display effect under standby status
6.2 Door lock is activated: oven will be locked under following status:
•Among all function mode(except for defrost mode),door lock will automatically be
activated when oven cavity temperature is higher than 300℃.
•During self-cleaning process, door lock will be activated.
•When oven is under standby mode, and temperature sensor is open-circuit or short
circuit, door lock will be activated and cooling fan still works, display effect will be as
picture 8 shown.
6.3 Door lock is relieved: oven will be unlocked meeting the following requirements:
•When self-cleaning process is completed or paused, oven door lock will automatically
be relieved only when oven cavity temperature drops to below 280℃.If electricity is cut
off during self-cleaning process, oven door will be unlocked only after power on again.
(Note: Even if power on again, oven door will be automatically unlocked only when
cavity temperature is below 280℃.)
•During other function mode working, if oven temperature is abnormal, the oven door will
be relieved only when cavity temperature is below 280℃.

16
6.4 Forced unlocking: In the case of oven lock, you can press and hold the “K2+K4” button
to unlock in the oven standby state. When you hear the sound “Di” the door lock is forced
unlock, the door lock icon will be extinguished. The door can be opened and door lock
function is disabled.
Note: After the oven door lock is forcibly unlocked, the oven must be powered off and
re-powered. The door lock will be self-tested after the power-on process, and the oven
can be used normally after self-test.
7. Protection function
7.1 Display will show E-1 if sensor is short circuit or open circuit under cooking mode,
buzzer will continuously prompt for 10 times (1s/time), refer to display effect 10. Oven will
be locked at this time, touch “ ” button can return to standby mode.
Pic 10: Sensor abnormal alarm display effect
7.2 When the temperature <35℃after 5 minutes of heating(except for defrost mode and
Eco mode), it means the heating element have a problem, display will show E-2, buzzer will
continuously prompt for 10 times(1s/time), refer to display effect shown as pic 11.Touch “ ”
button can return to standby status at this time.
Pic 11: Heat element abnormal alarm display effect
7.3 During self-cleaning process, if display screen shows fault code “E-3” when door is
locked into place, it means door lock or detection circuit is faulty. When the fault code
appears, the buzzer will continuously prompt for 10 times (1s/time), display effect as below
pic 12).Touch “ ” button can return to standby status.
Pic 12: Door lock abnormal alarm display effect

17
7.4 In any state, when the power board cannot receive valid communication data from the
display board for 20 seconds, the power board automatically turns off all loads, and the
display board displays "E-5". When the display board cannot receive valid communication
data from the power board for 20 seconds, the display board sends data to close all loads,
and the display board displays "E-6".
Error
code
Description Reason
E-1 Open or shorted sensor Sensor or detection circuit failure
E-2 Sensor failure Sensor or heating element failure
E-3 Door lock failure Door lock or detection circuit failure
E-4
MCU Register failure
MCU failure
E-5
The power board cannot receive the
effective communication data from the
display board for 20 seconds, and the
power board automatically turns off all
loads.
Communication line failure
E-6
The display board cannot receive valid
communication data from the power board
for 20 seconds, and the display board sends
data to turn off the load.
Communication line failure
E-7
High temperature protection occurs, and
the load is turned off within 10 seconds.
Defective sensor or heating element
drive circuit
8. Enquiry function
(1) Under barbecue state, touch “ ” button once can query system time, the clock position
shows the current time of the system, second icon will flash. Re-touch “ ” button or 10s
later automatically return to the barbecue time display.
(2) After the reminder time setting is completed, and the oven in the reservation or
barbecue state, touch “ ” can query the alarm remaining countdown. Re-touch “ ”
button or 10s later automatically return to its original state. You can query the remaining
alarm time and reset the alarm time under standby state. When the alarm countdown
time is less than 1 minute, the clock position shows 0：00.
(3) In the reservation status, first touch of the“ ” can query the cooking start time, the
clock position shows the cooking start time, clock value flashes. Re-touch “ ” button or
10s later automatically return to the system time display.
9. Alarm function
Touch “ ” button under standby state to enter to reminder function setting, at this time the
clock position hour value will flash, minute value will long lit. The reminder time setting icon
“” flashes, the reminder time icon “ ” is always on.
(1) Rotate programming switch KB2 to set the hour, at this time the hour value is always
bright, the value setting range is 0-23;

18
(2) Touch “ ” button again, minute value flashes, and hour value keeps bright;
(3) Rotate programming switch KB2 to set the minute, at this time the value of the minute is
always bright, the setting range is 0-59;
(4) When the alarm time is set, you can touch “ ” for confirmation. At this time, the display
shows the system time, the reminder time setting icon “ ” goes out ,the second icon “ ”
flashes, the “ ”is always on, and the reminder time starts to count down in seconds.
When the time countdown is 00:00, buzzer will sound for 1 minute (1s/time), and the
reminder time icon “ ” is always flashing (1s/time), then press any button to stop
flashing.
Note:
1) During setup, second icon “ ” and alarm clock icon “ ” will always bright.
2) During setup, touch “ ” button will cancel the current reminder time setting and return to
standby state.
3) If a reminder function has been set, then reminder icon “”should always be displayed
when the menu is working, and the reminder time can be queried.
10. Start/pause/cancel function
•After setting up the cooking function, touch “ ” button to start working; if touching “ ”
button when the cooking is suspended, you can restart the work.
•During oven cooking, touch “ ” button once can pause the cooking, temperature and
time will flash display, oven working icon“ ” flashes, function icon is always on; Touch
“ ” button again will cancel current cooking.
•When setting system time, press “ ” button to exit the clock setting state directly and
return to standby state.
•When oven function, cooking time and temperature are set, press “ ” button to exit
function setting state and return to standby state.
•After setting the reservation function or entering the reservation function, press the “ ”
button can return to the standby mode directly.
11. Other instructions
(1) Button sound
(2) Sound for touching the button
(3) Alarm sound: Heating element faulty sound, sensor fault sound;
(4) Prompt sound: The temperature reaches the set value, the cooking time counts down to
0, and the alarm time counts down to 0.
Settings & functions of the oven
This appliance has 9 grill functions available.
Icons
Function description