VoiSmart NT-3010-01-16POE User manual

NT-3010-01-16POE
16-PORT 10/100M POE SWITCH
Quick Installation Guide
FCC Warning
This device has been tested and found to comply
with limits for a Class A digital device, pursuant to
Part 15 of FCC Rules. These limits are
designed to provide reasonable protection
against harmful interference when the equipment
is operated in a commercial environment. This
equipment generates and radiates radio
frequency energy and, if not installed and used in
accordance with the user’s manual, it may cause
interference in which case users will be required
to correct interference at their own expenses.
CE Warning
This is a Class A product. In a domestic
environment, this product may cause radio
interference in which case the user may be
required to take adequate measures.
Introduction
This switch provides 16 10/100M ports. It is
designed for easy installation and high
performance in an environment where traffic is on
the network and the number of users increases
continuously.
It consists of 16 PSE/PoE ports. This can solve
the limitation of the power outlet location and offer
the system designer a flexible solution to locate
the network device everywhere.
The rack-mount size was specifically designed for
medium to large workgroups. The Switch can be
installed where space is limited; moreover it
provides smooth network migration and easy to
upgrade the network capacity. The 19” size can
be rack-mount on 19” cabinet.
Package Contents
Before you start to install this switch, please
verify your package that contains the following
items:
 One PoE Web Smart Switch
 One Power Cord
 19” Rack Mount Kit
Note: If any of these items is found missing or
damaged, please contact your local supplier
for replacement.
Key Features
 16 Port 10/100M Nway (Auto-negotiation)
Web Smart Switch
 16 PSE/PoE function ports
 Supporting the power Max. 15.4 W for each
PSE/PoE port (Total Power: 130W)
 483mm (19”) rack-mount size
 Auto-learn of networking configurations
 Auto-detect full/half-duplex modes for any
port
 Dedicated full-duplex 200Mbps bandwidth
 Store-and-Forward switching methods
 IEEE 802.3x flow control for full-duplex and
back-pressure flow control for half-duplex
 Non-blocking & Non-head-of-line blocking
full wire speed forwarding
 Auto-MDI/MDI-X function for any port
 Smart plug & play
Front Panel (LEDs)
LED Status Description
On Power is on Power
Off Power is off
On Connection established
Off No connection
LINK/ACT
Flashing Data is transmitting or
receiving
On Port is linked to Power
Device
PoE
Off No Power Device is
connected
Connections
Switch/Hub to this 16 Port PoE Fast
Ethernet Switch
This switch provides automatic crossover
detection functionality for any port. It is
simple and friendly to up-link to another
switch without crossover cable.

PC/Other devices to this 16 Ports Fast
Ethernet Switch
Via a twisted pair cable straight through, this
switch can be connected to PCs, servers and
other network devices.
Power Device to this 16 Port PoE Fast
Ethernet Switch and getting 48V power
source through Cat. 5 cables
Using Cat. 5 twisted-pair cable to connect
Power
Device to the port 1~16 of this switch. Then this
switch will supply 48V power to Power Device
over Cat. 5 twisted-pair
cable. Please be noted
Power Device should also comply with IEEE
802.3af standard.
Rear Panel (Power)
AC input
AC input (100~240V/AC,50~60Hz)
Technical Specifications
Standards
 IEEE 802.3 10BaseT
 IEEE 802.3u 100BaseTX
 IEEE 802.3x
Full-duplex and Flow Control
 IEEE 802.3ad
Trunk (Link Aggregation)
 IEEE 802.3af
Power Over Ethernet (PoE)
 IEEE 802.1Q VLAN
 IEEE 802.1p Class of Service
 IEEE 802.1d
Spanning Tree Protocol
 IEEE 802.1w
Rapid Spanning Tree Protocol
Features
Number of Ports: 16 PoE Ports
MAC Address: 4K
Buffer Memory: 1.625 Mb
Method: Store and Forward
Filtering/
Forwarding Rates
100Mbps port – 148,800pps
10Mbps – 14,880pps
Transmission
Media 10/100BaseTX Cat. 5 UTP/STP
LED
Indicators
Per Port : LINK/ACT, PoE
Per Unit: Power
Power Input 100~240V/AC, 50~60Hz
Power Output 48V/DC Per Port Output –
15.4 W Max Per Port
Power
Consumption 130 Watts (Max)
Dimensions 440 × 220 × 44 mm
(L x W x H)
Weight 3.2 kgs
Operating
Temperature 0 to 45°C
Storage
Temperature -20 to 90°C
Humidity 10 to 90% RH
(non-condensing)
Certifications FCC Class A, CE