VOKERA AriaPRO 004 M User manual

AriaPRO
High efficiency heat pumps
Users Instructions
Installation &
Servicing
Instructions
THESE INSTRUCTIONS
TO BE RETAINED
BY USER
Vokèra is a licensed member of the Benchmark scheme
which aims to improve the standards of installation and
commissioning of domestic hot water systems in the UK.

2

Titolo_fittizio
Titolo_fittizio
Dear Customer,
Thank you for choosing a Vokèra AriaPRO.
This booklet contains information necessary for the correct installation
of this appliance.
Thanks again.
VOKÈRA Ltd.
Compliance
Titolo_fittizio
The unit complies with the following Standards:
Electromagnetic Compatibility Directive 2004/108/EC as subsequently
amended
Machinery Directive 2006/42/EC as subsequently amended
Range
Titolo_fittizio
Warranty
Titolo_fittizio
The Vokèra product you bought has a SPECIFIC WARRANTY, valid from
the date of installation.
Conditions are specified in the WARRANTY CERTIFICATE, which we invite
you to read carefully.
Contents
Titolo_fittizio
The following symbols are used in this publication:
This booklet cod. R&S 330 - Rev. 0 - (4/11) consists of 36 pages.
WARNING = actions requiring special care and appropriate training.
DO NOT = actions that MUST ON NO ACCOUNT be carried out.
Titolo_fittizio
Heat pumps Code
AriaPRO 004 M 20033107
AriaPRO 006 M 20033108
AriaPRO 008 M 20033109
AriaPRO 012 M 20033110
AriaPRO 015 M 20033111
General
General notices
Titolo_fittizio
Check the integrity and completeness of the supplied equipment
as soon as you take it out of its packaging. If necessary, consult the
Agency that sold you the equipment.
All VOKÈRA equipment shall be installed by competent persons. The
installation must conform to current Legislation and the instructions in
this booklet.
These units must comply with their intended use, pursuant to their
performance characteristics.
VOKÈRA will not accept any liability for damages to property, people or
animals because of installation, calibration and maintenance mistakes
or erroneous usage of the equipment.
In case of abnormal operation, or leaks of liquids or refrigerant gases,
position the main switch of the system in the “off” position and close
the stop taps. Call VOKÈRA’s Technical Service or other professionally
qualified personnel immediately. Do not try to repair the unit.
This booklet must be kept carefully as it is an integral part of the
equipment and must ALWAYS be present, including in case of sale
of the equipment to another owner or user, or of transfer to another
system. Should the manual get damaged or lost, please ask for a
duplicate manual from the VOKÈRA’s Technical Service.
Repairs or maintenance actions must be carried out by VOKÈRA’s
Technical Service staff or other skilled staff, pursuant to the provisions
of this publication. Do not modify or tamper with this equipment, as
doing so might cause dangerous situation, for which the manufacturer
waives all liability.
In the installation and/or maintenance operations please adopt the
appropriate attire and accident prevention devices. The Manufacturer
waives all and any responsibility for failure to observe the safety and
accident prevention regulations from time to time in force.
Comply with the legislation in force on the country of deployment
with regard to the use and disposal of packaging, of cleaning
and maintenance products and for the management of the unit’s
decommissioning.
Pursuant to the EC standard n. 842/2006 on certain fluorinated
greenhouse gases, it is mandatory to declare the exact quantity of
refrigerant present in the installed system. This piece of information can
be found on the technical tag attached to the outdoor unit.
This unit contains fluorinated greenhouse gases covered by the Kyoto
protocol. Maintenance and disposal activities must be carried out
exclusively by skilled personnel.
The units contain refrigerant gas: handle them carefully, to avoid
damaging the gas circuit.
Fundamental safety rules
Titolo_fittizio
Do not allow children or unassisted disabled people to use the unit.
Do not open the access covers and carry out technical or cleaning
activities before disconnecting the unit from the power grid by
positioning the system’s main switch in the “off” position.
It is forbidden to modify the safety or regulation devices without the
authorisation and directions of the manufacturer.
Do not stand, sit and/or place objects on the unit.
Do not pull, detach or twist the electrical wires coming out of the unit,
even when the unit is disconnected from the power grid.
Do not spray or throw water directly on the unit.
Do not dispose of, abandon or leave the potentially hazardous
packaging materials within the reach of children.
It is strictly forbidden to touch any moving parts, interfere with them or
introduce pointed objects through the grids.
General
General notices ........................................ 3
Fundamental safety rules ................................. 3
Description ........................................... 4
Identification .......................................... 4
Technical Data......................................... 5
Dimensions ........................................... 7
Electrical diagrams...................................... 8
Refrigerating circuit ..................................... 18
Installer
Product delivery........................................ 18
Handling and transportation ............................... 18
Access to inner parts...................................... 18
Installation ............................................ 19
Hydraulic connections ................................... 20
Condensate discharge connection.......................... 20
Electrical connections ................................... 21
Control panel.......................................... 22
System’s charging ...................................... 23
Technical Service
First commissioning..................................... 23
Stop for an extended period of time ......................... 23
System’s drainage ...................................... 23
Ordinary maintenance ................................... 23
Extraordinary maintenance ................................ 24
Control
Control panel.......................................... 25
Functions ............................................ 26
Abnormal operations
Anomalies warnings....................................... 29
3

Description
AriaPRO
The product is characterised by:
PAM and PWN modulation DC-INVERTER control, which allows the
compressor to modulate its performance continuously from 30% up to
120%, guaranteeing high energetic standards at all moments.
Pre-painted sheet metal cabinet.
Revolving TWIN ROTARY-type compressor mounted on antivibrating
mounts and placed in a special compartment.
Electronically controlled variable speed fan, ensuring a highly silent
operation.
AISI 316 stainless steel plate heat exchanger, utilities side, insulated
with closed cell anticondensation lining, complete with resistor and
differential pressure switch.
Exchanger made of copper pipes and aluminium corrugated fins.
Safety devices such as pressure switches, sensors, specific automatic
switches and main door-blocking switch.
Phase monitor.
Integrated hydronic module, quickly installed with the help of a few
external components.
Micro-processor electronic control regulation performance
Climate control.
Titolo_fittizio
The AriaPRO range units are designed for the production of refrigerated
water for air conditioning, heated water for heating and sanitary hot water
for homes, residential units, etc., and are used together with terminal units
for small and medium systems.
They are designed for outdoor installation, so their constituent materials
were chosen for this specific requirement.
Identification
Technical Tag
The technical tag shows all technical and performance data of the
unit. Should the tag get lost, please ask for a duplicate tag from the
VOKÈRA’s Technical Service.
Any tampering with, the removal or the lack of the Technical Tag or of
any other element whose absence prevents certain identification of
the product makes it more difficult to install and maintain the product.
8
9
10
1
2
4
6
7
4
3
6
5
5
2
4
1
7
3
4
004 - 006 - 008 012 - 015
1Automatic air vent valve
2Flow meter
3Safety valve (output 1 / 2 ‘)
4Temperature probe
5Recirculation pump
6Cap to release pump seizure
7Expansion tank
8Position 4 LED Inverter Board Diagnostics (models 012 M - 015 M)
9Location of Diagnostic LEDs circuit board
10 Wiring terminal
4

Technical Data
Titolo_fittizio
Model 004 M 006 M 008 M 012 M 015 M
Output in heating mode
Nominal capacity(1) kW 4.1 5.8 7.2 11.9 14.5
Power Consumption(1) kW 1.01 1.38 1.84 3.04 3.57
COP(1) kW 4.05 4.2 3.91 4.06
Energy class(1) A B A
Nominal capacity(2) kW 3.9 5.8 7.4 12.95 14
Power Consumption(2) kW 1.21 1.93 2.34 4.3 4.36
COP(2) kW 3.2 3.01 3.16 3.01 3.21
Energy class(2) A B
Nominal capacity(3) kW 3.5 3.8 4.1 8 10.2
Power Consumption(3) kW 1.13 1.23 1.31 2.6 3.29
COP(3) kW 3.1
Nominal capacity(4) kW 3.4 3.7 3.9 8 10.2
Power Consumption(4) kW 1.31 1.42 1.48 3.08 3.92
COP(4) kW 2.6
Nominal capacity(5) kW 4.1 5.4 6.7 11.5 11.7
Power Consumption(5) kW 1.51 2.09 2.91 4.64 4.18
COP(5) kW 2.71 2.58 2.3 2.48 2.8
Output in cooling mode
Nominal capacity(6) kW 4.9 7 7.8 13.5 16
Power Consumption(6) kW 1.21 1.94 2 3.74 4.2
EER(6) kW 4.05 3.61 3.9 3.61 3.81
Energy class(6) A B A
Nominal capacity(7) kW 3.3 4.7 5.8 10.2 13
Power Consumption(7) kW 1.13 1.61 3.03 3.5 4.47
EER(7) kW 2.91
ESEER(7) kW 4.5 4.6 4.4 4.3 4.4
Energy class(7) B
Generalities
Sound pressure in heating(1) dB(A) 42 44 47 48
Sound pressure in cooling(7) dB(A) 44 45 48 49
Compressor Rotary DC Inverter Tecnology
R410a refrigerant charge kg 1.195 1.35 1.81 2.45 3.39
Empty weight kg 63 61 71 105 130
Model 004 M 006 M 008 M 012 M 015 M
Sizing electric line
Power supply V- ph - Hz 230 - 1 -50
Allowable Voltage Range V 207 ÷ 254
Maximum power drawn kW 2 2,3 2,7 5,1 5,1
Maximum current drawn A 7,2 11 14 23 20
Type power fuses gL tipo
Power supply fuses A 10 - tipo B 15 - tipo B 15 - tipo B 25 - tipo D 25 - tipo D
Power supply cables mm2 H07RN-F 3 x 2.5mm2
Maximum pump current external circulation A 2
Note
1outdoor temperature D.b. + 7 °C / w.b. + 6°C, water 35 - 30 °C.
2outdoor temperature + 7 °C / w.b. + 6°C, water 45 - 40 °C.
3outdoor temperature D.b. + 2 °C / w.b. +1 °C, water 35 - 30 °C.
4outdoor temperature D.b. + 2 °C / w.b. +1 °C, water 45 - 40 °C.
5outdoor temperature D.b. + 7 °C / w.b. + 6°C, water 55 °C.
6outdoor temperature D.b.+35 °C / w.b.+24°C, water 18 - 23 °C.
7outdoor temperature D.b. +35 °C, water 7 - 12 °C.
Standard conditions
Sound pressure measured in a hemispheric field 4 meters in front of
the fan.
Unit performances are compliant with Directive UNI EN 14511:2004.
Fouling factor: 0.18 x 10-4 (m2 K)/W.
5

Operating conditions
With models 004 - 006, min. outdoor air temperature must be +5°C if
operating in cooling mode.
For the optimum working of the heat pump when producing hot water
in summer operation, outdoor air temperature should not exceed
30°C.
When outdoor air temperature exceeds 30°C, hot water production
may be limited according to the settings of the safety devices in the
equipment.
For technical activities, please refer to the technical tag mounted on
board the machine
It is forbidden to work outside of the working field
1Cooling
2Heating
AOutdoor temperature (°C)
BOutlet water temperature (°C)
12
10
15
20
25
30
35
40
45
50
55
60
65
70
-25-20 -15-10 -5 0510 15 20 25 30 35
A
B
A
B
0
2
4
6
8
10
12
14
16
18
20
-5 0510 15 20 25 30 35 40 45 50
008-012-015
004
006
6

Flow-rate/head diagram
0
5
10
15
20
25
30
35
40
45
50
55
60
00,360,721,081,441,8 2,16
A
B
A
B
0
5
10
15
20
25
30
35
40
45
50
55
60
0 0,360,721,081,44 1,82,16
A
B
0
00,360,721,081,441,8 2,16 2,52 2,88 3,24
10
20
30
40
50
60
70
80
90
A
B
AriaPro 006 M
AriaPro 004 M
AriaPro 008 M AriaPro 012 M - 015 M
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
0,2 0,3 0,4 0,50,10,0
Dimensions
Titolo_fittizio
Modello 004 M 006 M 008 M 012 M 015 M
Dimensions
Empty weight kg 61 71 105
A mm 908
B mm 821 1363
C mm 326
D mm 350
E mm 87 174
F mm 356 640
G mm 466 750
H mm 40 44
L mm 60 69
7

R
R
W
W
C
C
Y
A
Y
Y
R
W
C
V
C
C
W
R
C
A
B
W
Y/G
Y/G
C
W
O
C
THERMOSTAT FOR
COMPRESSOR
CN805
1
1
CN701
1CN806
1
CN300
CN700
CN503
CN502
CN501
CN500
1
6
1
1
1
1
1
N
L
230V - 1~ - 50Hz
/2.10 / J4.1 /2.03 / J3.1 /2.08 / J1.1
1FM
1CM
R
S
C
40CF
12 3
7CM 123
1R
41CF
21
8CM 21
2T 12
P25
P24
P23
P22
P21
P20
P35
P34
P19
P18
P04
P05
P06
1P.C.BOARD
P11
P08
1MCC-1530
42CF 123
43CF 123
P33 P32
2R
44CF
21
9CM 21
P31 P30
45CF
123
1RV
F7 P03 P10 P02
1TB
1N
46CF
3
2
1
47CF
6
5
4
3
2
1
48CF
3
2
1
49CF
2
1
50CF
3
2
1
51CF
2
1
3 L N PE
1TS
1TO
1TD
1TE
1PMV
004 M Power
-Wiring of the manufacturer
---- Field wiring
CM Compressor motor
FM Fan engine
RV Reversing valve (4 way)
TS Probe temperature low-pressure pipe
TO
TD Probe temperature high pressure pipe
TE Temperature probe capacitor pipe
PMV Modulating valve engine
RRed
FFuse
LWT Outlet water sensor
EWT Inlet water sensor
TR Refrigerant sensor
FS Flow meter
TTransformer
PS Water pump motor
E-HTR Electric Heater
AD Alarm status and defrost
OAT Outside air probe
LF Limiting frequency
IS Health input
SV Three-way health valve
YYellow
OOrange
ABrown
CBlack
VPurple
BBlue
WWhite
Y/G Yellow Green
Electrical diagrams
8

004 M Control
A
B
R
R
C
O
A
R
G
Y/G
BA
O
W
G
Y
C
Y/G
Y/G
W
G
OR
G
A
R
C
A
W
C
A
G
C
B
B
B
B
C
1
1
1
1
1
1
J18
J11
1
J6A
J6B
J6C
J16
J5
1
J20
1
J17
J10
11
J22
1
J13
1
J7
1
J2
1
J4
ALARM
REMOTE
CONTROL
REMOTE
CONTROLREMOTE
ALARMEHS
/
DFR
ALARM +
DFR
/
HUMIDITY
EHTR
/
WP
ALARM
INPUT
1LWT 1TR 1EWT
1T
J4.1 / /1.05
J1.1 / /1.05
1FS
1
2
/1.05 / J3.1
1OAT
1LF
1
2
1IS
1
2
24CF
12345
25CF
12 3
26CF
12 3
28CF 1
2
29CF 1
2
30CF 1
2
31CF 1
2
32CF 7
6
5
4
3
2
1
33CF
123456
34CF
7654321
35CF
1234
36CF
123456
37CF
12345
3TB
C W G Y 23 24 1
2TB
N 18 10 11 12
5TB
21 22 3 6 7 8 2
4TB
4 5 16 13 14 15
N
38CF
1
2
1PCB
J6A.1
J6A.2
J6B.1
J6B.2
J6B.1
J6B.2
J18.1
J18.2
J11.7
J11.6
J11.5
J11.4
J11.3
J11.2
J11.1
J16.1J16.2
J5.1
J16.3
J5.2
J16.4
J5.3
J16.5
J5.4
J16.6
J5.5
J20.7J20.6
J15.1
J20.5
J15
J17.1
J17.2
J10.1
J20.4
J10.2
J20.3
J10.3
J20.2
J10.4
J20.1
J10.5 J10.6
J22.1 J22.2 J22.3
J13.1
J22.4
J13.2 J13.3
J7.1
J2.1
J7.2
J2.2
J7.3
J2.3
J7.4 J7.5 J7.6
J1.1
J1
J4.1 J4.2 J4.3 J4.4 J4.5
J3
39CF
1
2
3
5CM
1
2
3
1PS
1SV
9

R
R
W
W
C
C
Y
A
Y
Y
R
W
C
V
C
C
W
R
C
A
B
W
Y/G
Y/G
C
W
O
C
THERMOSTAT FOR
COMPRESSOR
CN805
1
1
CN701
1CN806
1
CN300
CN700
CN503
CN502
CN501
CN500
1
6
1
1
1
1
1
N
L
230V - 1~ - 50Hz
/2.10 / J4.1 /2.03 / J3.1 /2.08 / J1.1
1FM
1CM
R
S
C
40CF
12 3
7CM 123
1R
41CF
21
8CM 21
2T 12
P25
P24
P23
P22
P21
P20
P35
P34
P19
P18
P04
P05
P06
1P.C.BOARD
P11
P08
1MCC-1530
42CF 123
43CF 123
P33 P32
2R
44CF
21
9CM 21
P31 P30
45CF
123
1RV
F7 P03 P10 P02
1TB
1N
46CF
3
2
1
47CF
6
5
4
3
2
1
48CF
3
2
1
49CF
2
1
50CF
3
2
1
51CF
2
1
3 L N PE
1TS
1TO
1TD
1TE
1PMV
006 M Power
10

006 M Control
A
B
R
R
C
O
A
R
G
Y/G
BA
O
W
G
Y
C
Y/G
Y/G
W
G
OR
G
A
R
C
A
W
C
A
G
C
B
B
B
B
C
1
1
1
1
1
1
J18
J11
1
J6A
J6B
J6C
J16
J5
1
J20
1
J17
J10
11
J22
1
J13
1
J7
1
J2
1
J4
ALARM
REMOTE
CONTROL
REMOTE
CONTROLREMOTE
ALARMEHS
/
DFR
ALARM +
DFR
/
HUMIDITY
EHTR
/
WP
ALARM
INPUT
1LWT 1TR 1EWT
1T
J4.1 / /1.05
J1.1 / /1.05
1FS
1
2
/1.05 / J3.1
1OAT
1LF
1
2
1IS
1
2
24CF
12345
25CF
12 3
26CF
12 3
28CF 1
2
29CF 1
2
30CF 1
2
31CF 1
2
32CF 7
6
5
4
3
2
1
33CF
123456
34CF
7654321
35CF
1234
36CF
123456
37CF
12345
3TB
C W G Y 23 24 1
2TB
N 18 10 11 12
5TB
21 22 3 6 7 8 2
4TB
4 5 16 13 14 15
N
38CF
1
2
1PCB
J6A.1
J6A.2
J6B.1
J6B.2
J6B.1
J6B.2
J18.1
J18.2
J11.7
J11.6
J11.5
J11.4
J11.3
J11.2
J11.1
J16.1J16.2
J5.1
J16.3
J5.2
J16.4
J5.3
J16.5
J5.4
J16.6
J5.5
J20.7J20.6
J15.1
J20.5
J15
J17.1
J17.2
J10.1
J20.4
J10.2
J20.3
J10.3
J20.2
J10.4
J20.1
J10.5 J10.6
J22.1 J22.2 J22.3
J13.1
J22.4
J13.2 J13.3
J7.1
J2.1
J7.2
J2.2
J7.3
J2.3
J7.4 J7.5 J7.6
J1.1
J1
J4.1 J4.2 J4.3 J4.4 J4.5
J3
39CF
1
2
3
5CM
1
2
3
1PS
1SV
11

008 M Power
R
R
W
W
C
C
Y
A
Y
Y
R
W
C
V
CC
C
W
W
R
W
R
Y/G
O
W
Y/G
R
C
B
A
THERMOSTAT FOR
COMPRESSOR
CN805
1
1
CN701
1CN806
1
CN300
CN700
CN503
CN502
CN501
CN500
1
6
1
1
1
1
1
N
L
230V - 1~ - 50Hz
1FM
6CM
R
S
C
40CF
12 3
7CM 123
1R
41CF
21
8CM 21
2T 12
P25
P24
P23
P22
P21
P20
P35
P34
P19
P18
P04
P05
P06
1P.C.BOARD
P11
P08
1MCC-1530
42CF 123
43CF 12 3
P33 P32
2R
44CF
21
9CM 21
P31 P30
45CF
123
1RV
F7 P03
1F
12
P10 P02
3R
1TB
1N
46CF
3
2
1
47CF
6
5
4
3
2
1
48CF
3
2
1
49CF
2
1
50CF
3
2
1
51CF
2
1
3 L N PE
1TS
1TO
1TD
1TE
1PMV
/2.10 / J4.1 /2.02 / J3.1 /2.08 / J1.1
12

008 M Control
G
B
Y/G
Y/G
B
B
O
W
G
Y/G
Y
G
C
O
R
R
A
CG
A
O
B
A
C
G
C
R
B
W
W
A
C
R
A
R
C
B
A
1
1
1
1
1
1
J18
J11
1
J6A
J6B
J6C
ALARM +
DFR
/
HUMIDITY
J16
EHTR
/
WP
J5
REMOTE
1
J20
1
J17
J10
11
ALARM
REMOTE
CONTROL
J22
1
J13
1
J7
EHS
/
DFR
1
ALARM
J2
1
J4
ALARM
INPUTREMOTE
CONTROL
1PS
1LWT
10CM
1
2
3
52CF
1
2
3
1TR
/1.05 / J3.1
1EWT
2TB
NN 18
1SV
1PCB
53CF 1
2
54CF 1
2
55CF 1
2
56CF 1
2
57CF 7
6
5
4
3
2
1
J6A.1
J6A.2
J6B.1
J6B.2
J6B.1
J6B.2
J18.1
J18.2
J11.7
J11.6
J11.5
J11.4
J11.3
J11.2
J11.1
10
58CF
123456
J16.1J16.2
59CF
12345
J5.1
11
J16.3
J5.2
J16.4
J5.3
12
J16.5
J5.4
J16.6
3TB
J5.5
C
60CF
7654321
J20.7
W
J20.6
1FS
1
2
G
61CF
1
2
J15.1
J20.5
J15
Y
J17.1
J17.2
J10.1
J20.4
23
J10.2
J20.3
24
J10.3
J20.2
1
1OAT
J10.4
J20.1
J10.5 J10.6
62CF
1234
J22.1 J22.2 J22.3
63CF
12 3
J13.1
J22.4
J13.2
3T
J13.3
64CF
123456
4TB
J7.1
4
65CF
12 3
J2.1
J7.2
J2.2
J7.3
5
J2.3
J7.4 J7.5
16
J7.6
13
J1.1
J1.1 / /1.05
J1
2FL
1
2
14
66CF
12345
J4.1 J4.2
1IS
1
2
15
J4.3 J4.4
5TB
21
J4.5
J3
22 3 6
J4.1 / /1.05
7 8 2
13

012 M Power
R
W
C
Y/G
W
R
WG
C
G
O
OA
PRB
C
WC Y
Y
B
B
O
O
C
W
R
R
R
W
W
C
C
B
A
230V - 1~ - 50Hz
LN
1
CN700
1
CN02
1
1
1
R
CN13
CN01
CN702
R
1
1
CN05
CN04
1CN303
1
1
+
CN800
CN06
-
-
-
-
ED
1CN302
1
1
CN04
CN03
CN600
1
1CN301
1CN600
1CN300
1CN605 1CN604
THERMOSTAT
FOR COMPRESSOR
1CN500
1CN601
1CN606
1TB
PE
1F
1
2
L
1RV
N
39CF1
2
3
40CF1
2
3
4
5
CN01
CN02
CN03
1P.C.BOARD
2P.C.BOARD
7CM
123
41CF 123
P08
42CF 12345
43CF 12345
1PVM
44CF 123456
2TB
P09
8CM
123
45CF 123
P12 P13
46CF 12
47CF 12
P21
48CF 123
P24
49CF 12345
50CF 12345
1FM
P28 P29
51CF 12345
52CF 123
53CF 12 3
P19 P20 P17 P18
54CF 123
55CF
1
2
CN09
CN10
CN11
2FM
1TH
1TD
56CF 12 3
57CF 12345
58CF
12
1TS
59CF
12
1TE
60CF
12
2T
1
2
61CF
12 3
1TO
1CM
R
C
S
1 N 3
J4.1 / /2.10
J3.1 / /2.03
J1.1 / /2.08
14

012 M Control
G
B
Y/G
Y/G
B
B
O
W
G
Y/G
Y
G
C
O
R
R
A
CG
A
O
B
A
C
G
C
R
B
W
W
A
C
R
A
R
C
B
A
1
1
1
1
1
1
J18
J11
1
J6A
J6B
J6C
ALARM +
DFR
/
HUMIDITY
J16
EHTR
/
WP
J5
REMOTE
1
J20
1
J17
J10
11
ALARM
REMOTE
CONTROL
J22
1
J13
1
J7
EHS
/
DFR
1
ALARM
J2
1
J4
ALARM
INPUT REMOTE
CONTROL
1PS
1LWT
9CM
1
2
3
62CF
1
2
3
1TR 1EWT
3TB
NN 18
1SV
1PCB
63CF 1
2
64CF 1
2
65CF 1
2
66CF 1
2
67CF 7
6
5
4
3
2
1
J6A.1
J6A.2
J6B.1
J6B.2
J6B.1
J6B.2
J18.1
J18.2
J11.7
J11.6
J11.5
J11.4
J11.3
J11.2
J11.1
10
68CF
123456
J16.1J16.2
69CF
12345
J5.1
11
J16.3
J5.2
J16.4
J5.3
12
J16.5
J5.4
J16.6
4TB
J5.5
C
70CF
7654321
J20.7
W
J20.6
1FS
1
2
G
71CF
1
2
J15.1
J20.5
J15
Y
J17.1
J17.2
J10.1
J20.4
23
J10.2
J20.3
24
J10.3
J20.2
1
1OAT
J10.4
J20.1
J10.5J10.6
72CF
1234
J22.1J22.2J22.3
73CF
12 3
J13.1
J22.4
J13.2
3T
J13.3
74CF
123456
5TB
J7.1
4
75CF
123
J2.1
J7.2
J2.2
J7.3
5
J2.3
J7.4 J7.5
16
J7.6
13
J1.1
J1.1 / /1.05
J1
1FL
1
2
14
76CF
12345
J4.1 J4.2
1IS
1
2
15
J4.3 J4.4
6TB
21
J4.5
J3
22 3 6
J4.1 / /1.05
7 8 2
15

015 M Power
RC
W
C
A
B
C
W
R
G
W
R
230V - 1~ - 50Hz
L
N
UVW
CN400
(WHITE)
CN300
(WHITE)
CN609
(BLUE)
CN610
(YELLOW)
CN604
(WHITE)
CN603
(WHITE)
CN602
(YELLOW)
CN601
(WHITE)
CN600
(WHITE)
CN710
(WHITE)
SW802
SW804
SW803
ONONON
432143214321
SW801
CN704
(BLUE)
SW800
RY704
P04
CN701
(WHITE)
P05
CONTROL P.C. BOARD
MCC-1571
P06
CN04
(WHITE)
P07 CN200
F03
T10A,250V~
F01
T25A,250V~
CN201
P01
L/F
P02
CN202
P09
1TB
2TB
1 2 3
J4.1 / /2.10
J3.1 / /2.03
J1.1 / /2.08
1CM
63CF 12 64CF 12
1PCB
10CM
12
11CM
12
1R 2R
1FM
2FM
49C
12
1TL
1TD
1TO
1TE
1TS
L N
1PMV
65CF
1
2
3
66CF
1
2
67CF
1
2
68CF
1
2
3
69CF
1
2
70CF
1
2
71CF
1
2
3
72CF 123456 73CF 12 34 74CF 123456
75CF
1
2
3
1RV
16

015 M Control
A
B
R
R
A
RO G
C
O
C
A
R
B
G
Y/G
W
O
W
G
Y
Y/G
Y/G
B
G
B
B
R
A
W
C
G
C
C
A
A
B
C
1
1
1
1
1
1
J18
J11
1
J6A
J6B
J6C
J16
J5
1
J20
1
J17
J10
11
J22
1
J13
1
J7
1
J2
1
J4
REMOTE
CONTROL
ALARM
REMOTE
CONTROL
REMOTE
ALARMEHS
/
DFR
ALARM +
DFR
/
HUMIDITY
EHTR
/
WP
ALARM
INPUT
1LWT 1TR 1EWT
1T
J4.1 / /1.07
J1.1 / /1.07
1FS
1
2
/1.07 / J3.1
1OAT 1FL
1
2
1IS
1
2
24CF
12345
25CF
123
26CF
123
28CF 1
2
29CF 1
2
30CF 1
2
31CF 1
2
32CF 7
6
5
4
3
2
1
33CF
123456
34CF
7654321
35CF
1234
36CF
123456
37CF
12345
4TB
C W G Y 23 24 1
3TB
N 18 10 11 12
6TB
21 3 6 7 8 2
5TB
4 5 16 13 14 15
N
38CF
1
2
2PCB
J6A.1
J6A.2
J6B.1
J6B.2
J6B.1
J6B.2
J18.1
J18.2
J11.7
J11.6
J11.5
J11.4
J11.3
J11.2
J11.1
J16.1J16.2
J5.1
J16.3
J5.2
J16.4
J5.3
J16.5
J5.4
J16.6
J5.5
J20.7J20.6
J15.1
J20.5
J15
J17.1
J17.2
J10.1
J20.4
J10.2
J20.3
J10.3
J20.2
J10.4
J20.1
J10.5J10.6
J22.1 J22.2 J22.3
J13.1
J22.4
J13.2J13.3
J7.1
J2.1
J7.2
J2.2
J7.3
J2.3
J7.4 J7.5 J7.6
J1.1
J1
J4.1 J4.2 J4.3 J4.4 J4.5
J3
62CF
1
2
3
9CM
1
2
3
1PS
1SV
17

Refrigerating circuit
Titolo_fittizio
TS sensor TS sensor
TD sensor TD sensor
Accumulator Liquid accumulator
Rotary compressor Rotary compressor
Muffler Silencer
4-way valve 4-way valve
TO sensor TO sensor
Heat exchanger Heat exchanger
TE sensor TE sensor
Distributor Distributor
TR sensor TR Sensor
BPHE Plate heat exchanger
WE Water Inlet
WL Water outlet
PWM (Pulse Motor
Valve) Electronic expansion valve
PMV
(Pulse Motor Valve) WL
WE
TR sensor
Distributor
TE sensor
Heat exchanger
TO sensor
TS sensor
TD sensor
muffler
Muffler
Rotary compressor
Accumulator
4-way valve
B
P
H
E
Installer
Product delivery
Preliminary instructions
We suggest to take the equipment out of its packaging only when it
has been placed in position at the installation point.
Carefully remove any adhesive strips positioned on the unit.
Do not dispose of, abandon or leave the potentially hazardous
packaging materials within the reach of children.
Scope of supply
Also supplied:
Installer manual
External probe
Barcode labels
Control panel
Strain relief (size 015M only)
List of spare parts
The supplied accessories are positioned inside the electrical panel.
Cable gland
Drain discharge pipe
Handling and transportation
Titolo_fittizio
The unit must be handled by skilled technicians, appropriately
equipped and with the appropriate tools to manage the unit’s weight in
compliance with the accident prevention regulations.
When handled, the unit must always be kept in a vertical position.
The weight of the equipment is off balance towards the compressor.
If the unit is lifted, use pipes with a diameter and thickness appropriate
for the weight of the unit.
Use all the lifting points shown.
Access to inner parts
Titolo_fittizio
- Remove the access panel.
- Loosen the fastening screw.
60015
01
50
430
400
363
37
1
2
3
1Position 4 LED Inverter Board Diagnostics (models 012 M - 015 M)
2Location of Diagnostic LEDs circuit board
3Wiring terminal
18

Installation
Preliminary instructions
The place of installation must be determined by the system’s designer
or by an expert in the field and must take into account the technical
requirements and the current standards and legislation.
We suggest to avoid:
The placement in service ducts and/or hopper windows
Obstacles or barriers that cause a recirculation of the expelled air
Places with aggressive atmospheres
Small places where the unit’s noise level can be enhanced by
reverberation and resonance.
Placement in corners, where dust, leaves and other debris may easily
deposit ma reduce the efficiency of the unit, through obstruction of the
air flows.
The airflow from the unit can penetrate in the inhabited rooms through
doors or windows, creating discomfort.
That the airflow from the unit is opposed by a contrary wind.
The units must:
Be placed on a level surface able to support their weight.
Be placed on a sufficiently rigid floor slab that does not transfer vibrations
to the rooms below or next door.
It is suggested to place a rubber plate between the slab and the unit, or
to use anti-vibrating mounts appropriate for the unit’s weight.
The unit must be installed exclusively indoors.
If there are several units placed side by side on the bank side, the
required distances must be summed.
Provide for lifting of the unit from the floor:
20mm without conveying of condensation discharge
90 - 100 mm to allow the conveying of the condensation discharge
If the unit is installed in areas subject to heavy snowfall, it shall be
necessary to avoid the unit being directly exposed to it.
150
500
1000
1000
150 300 300
300
200
1000
300
200
300
1000
1000 1500 2000 200
300
150
200
150300
500
1000 150
19

Hydraulic connections
Preliminary instructions
The choice and installation of system components is left to the skilled
installer, who shall operate pursuant to the best practices and the
legislation from time to time in force.
Check that the pipes do not contain stones, sand, rust, debris or other
extraneous bodies that might damage the system.
It is appropriate to create a by-pass of the unit to make it possible to
wash the pipes without having to disconnect the unit.
The connection tubes must have the appropriate diameter and must
be supported, so as not to rest their weight on the unit.
Mandatory items:
Install a filter whose dimensions are appropriate for the impurities
present in the water entering the unit.
Install a flow meter for liquids, to be dimensioned and calibrated
according to the system’s hydraulic characteristics.
Install air venting valves in the highest points of the pipes.
Install flexible elastic joints to connect the pipes.
The flow meter must be positioned halfway through a stretch of
horizontal pipe with a length of at least 1 metre.
The system’s water content must prevent instabilities in the operation
of the refrigerating circuits.
Systems charges with anti-freezing agents or subject to special
regulations require the use of water disconnectors.
Failure to install filters, flow meter and anti-vibrating mounts can cause
obstruction, breakage and noise issues, for which the manufacturer
waives any liability.
Check charge losses from the unit, the system and any other in-line
mounted accessories.
The water flow must be maintained stable during operation.
The sealing of threads must be obtained using hemp and green paste.
Do not use Teflon when the unit contains anti-freeze liquid.
1On-off valve
2Line water filter (10 mesh / inch)
3Pressure gauge
4Filling valve
5Valve exhaust system (in lowest points of the circuit)
6Air vent (in the highest points of the circuit)
73-way valve
8Storage tank for domestic water
9House plant
10 Drain connection
1
1
2
3
3
4
6
5
78
9
430
10
37
Do not use the heat pump to treat the water used by industrial
processes, in swimming pools or in the house. In all these cases, an
intermediate heat exchanger is required.
Condensate discharge connection
With conveying
Connect a drainage tube to the connector on the collector tray and run it
towards and appropriate discharge area.
Without conveying
- The drainage capacity increases if the pre-cut holes in the base are
open.
In case of installation in very cold areas or areas subject to heavy
snowfall, where freezing out is a possibility, foresee appropriate
antifreeze systems.
20