Vortech MAXFLOW 5A102-036 User manual

DP/N: 007135v1.2 10/28/2018
MAXFLOW®FUEL PUMP BOOSTER
Installation Instructions
®
1650 Pacific Avenue, Channel Islands, CA 93033-9901 • Phone [phone]
Fax: [phone] • www.vortechsuperchargers.com • M-F 7:00 AM - 3:30 PM (PST)
ENGINEERING, INC.
2015-2018 MUSTANG GT
P/N: 5A102-036
* Legal in California only for racing vehicles which may never be used or registered or licensed for use upon a highway.

DP/N: 007135v1.2, 2018-10-24
© 2018 Vortech Engineering, Inc.
All Rights Reserved, Intl. Copr. Secured. ii
FOREWORD
Take note of the following before proceeding:
1. Proper installation of this accessory requires general automotive
mechanic knowledge and experience. Please browse through each step
of this instruction manual prior to beginning the installation to determine if
you should refer the job to a professional installer/technician. Please con-
tact your dealer or Vortech Engineering for possible installers in your
area.
2. This product was designed for use on stock (un-modified, OEM)
vehicles. The PCM (computer), engine, transmission, drive axle
ratios and tire O.D. must be stock. If the vehicle or engine has been mod-
ified in any way, check with Vortech prior to installation and use of this product.
3. Use only premium grade fuel with a minimum of 91 octane (R+M/2).
4. Always listen for any sign of detonatlion (knocking/pinging) and discontinue hard
use (no boost) until the problem is resolved.
5. Vortech is not responsible for any clutch, transmission, drive-line or engine dam-
age.
Exclusions from Vortech warranty coverage considerations
include, but not limited to:
1. Neglect, abuse, lack of maintenance, abnormal operation or improper installation.
2. Continued operation with an impaired vehicle or sub-system.
3. The combined use of Vortech components with other modifications such as, but
not limited to, exhaust headers, aftermarket camshafts, nitrous oxide, third party
PCM programming or other such changes.
©2018 VORTECH ENGINEERING, INC
All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, or translated into
another language in any form, by any means without written permission of Vortech Engineering, Inc.
All information, illustrations and specifications contained herein are based on the latest
product information available at the time of this publication. Changes to the manual may be
made at any time without notice. Contact Vortech Engineering for any additional informa-
tion regarding this kit and any of these modifications at [phone] 7:00am-3:30pm
PST.
STOP

DP/N: 007135v1.1, 2018-10-24
© 2018 Vortech Engineering, Inc.
All Rights Reserved, Intl. Copr. Secured.
iii
TABLE OF CONTENTS
FOREWORD ...................................................ii
TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
TOOL & SUPPLY REQUIREMENTS .................................iv
PARTS LIST ................................................... v
1. PREPARATION AND REMOVAL ...........................................1
2. FUEL PUMP BOOSTER INSTALLATION .....................................5
3. INTERIOR RE-ASSEMBLY................................................7
4. FINAL CHECK..........................................................9

DP/N: 007135v1.2, 2018-10-24
© 2018 Vortech Engineering, Inc.
All Rights Reserved, Intl. Copr. Secured. iv
VORTECH FUEL PUMP BOOSTER
Installation Instructions
2015-2018 MUSTANG GT
Before beginning this installation,
please read through this entire instruction booklet
The Vortech 2015-2018 Mustang GT Fuel Pump Booster (FPB) upgrade was designed
specifically for use on 2015-2018 Ford Mustang GT vehicles equipped with a turbo-
charger, supercharger or nitrous oxide, to support applications with increased horsepow-
er over the basic kit. As with any power enhancing product, this unit is intended for use
on healthy, well-maintained engines. Vortech Engineering is not responsible for engine
damage. Installation on new vehicles will not harm or adversely affect the break-in peri-
od so long as factory break-in procedures are followed.
For best performance and continued durability, please take a note of the following key
points:
1. Use only premium grade fuel 91 octane or higher (R+M/2).
2. Always listen for any sign of detonation (pinging) and discontinue hard use (no
boost) until problem is resolved.
TOOL & SUPPLY REQUIREMENTS:
• Interior Panel Removal Tools
• Drill Motor
• #4 or 7/32" Drill Bit
• 1/4" Drive Ratchet
• 1/4" Drive Extension
• 1/4" Drive 3/8" Socket
• 1/4" Drive 10mm Socket
• 5/32 Allen Key

DP/N: 007135v1.1, 2018-10-24
© 2018 Vortech Engineering, Inc.
All Rights Reserved, Intl. Copr. Secured.
v
PARTS LIST
2015-2018 MUSTANG GT
FUEL PUMP BOOSTER UPGRADE
Part No. 5A102-036
PART NO. DESCRIPTION QTY
007135 INSTR, ‘15-'18 MUST GT, PNP FPVB UPGRD 1
008601 BOX, CARDBOARD, PUMP BOOSTER 1
008602 INSERT, CARDBOARD, PUMP BOOSTER 1
4FQ010-090 MNTG PLT, ’15 MUST GT, FPVB 1
5A002-030 VOLT BOOSTER, PNP, STD, VORT LOGO 1
5W001-098 HARNESS, FPVB, PNP, ’11-’17 MUST GT 1
7C010-050 10-24 X .50 SHCS GR8 PLT 4
7E014-075 #14 X .75 HEX HD SHEETMETAL SCREW 2
7F010-024 10-24 NYLOCK NUT 4
7J010-001 WASHER, #10 FLAT, ZN PLT 4
7U100-055 TIE WRAP, 7.5" NYLON 5
IMPORTANT: Before beginning installation, verify that all parts are included in the kit.
Report any shortages or damaged parts immediately.

DP/N: 007135v1.2, 2018-10-24
© 2018 Vortech Engineering, Inc.
All Rights Reserved, Intl. Copr. Secured. vi
This page was left intentionally blank.

DP/N: 007135v1.1, 2018-10-24
© 2018 Vortech Engineering, Inc.
All Rights Reserved, Intl. Copr. Secured.
1
1. PREPARATION AND REMOVAL
Fig. 1-b: Unplug Battery Leads
B. Remove the battery cover and unplug both bat-
tery leads.
(See Fig. 1-b)
C. In order to access the fuel pump driver module,
it will be ncessary to remove the lower rear
seat cushion. There are two retainers located
underneath the front bolsters that secure the
lower rear seat cushion to the vehicle.
(See Fig. 1-c)
Fig. 1-c: Rear Seat Retainer Location
LOWER REAR SEAT CUSHION
RETAINER LOCATION
(LOCATED UNDERNEATH)
A. Prior to unplugging the battery, you will need to
roll down both windows. This is done to prevent
potential window damage as both windows rest
within a channel in the body of the vehicle
when they are rolled up.
(See Fig. 1-a)
Fig. 1-a: Roll Down Windows
NOTE: The provided mounting bracket for the fuel
pump booster is not compatible with con-
vertible vehicles at this time. Please con-
sult your local fabricator for a custom solu-
tion.

DP/N: 007135v1.2, 2018-10-24
© 2018 Vortech Engineering, Inc.
All Rights Reserved, Intl. Copr. Secured. 2
1. PREPARATION AND REMOVAL, cont'd
E. Located near the driver side rear interior panel
is the fuel pump driver module. Unplug the
electrical connector at this time.
(See Fig. 1-e)
F. Locate the upper rear seat release strap and
fold the upper rear seat down.
(See Fig. 1-f)
Fig. 1-e: Unplug Fuel Pump Driver Module
UPPER REAR
SEAT RELEASE
STRAP
Fig. 1-f: Fold Upper Rear Seat Down
D. In order to release the lower rear seat cushion
from the vehicle, press the retainer lever
inwards then pull the lower rear seat cushion
upwards.
(See Fig. 1-d)
Fig. 1-d: Rear Seat Retainer
PUSH RETAINER
LEVER INWARDS

DP/N: 007135v1.1, 2018-10-24
© 2018 Vortech Engineering, Inc.
All Rights Reserved, Intl. Copr. Secured.
3
1. PREPARATION AND REMOVAL, cont'd
G. Detach the rear seatbelt guide from the driver
side rear interior panel. The seatbelt passes
through the rear seatbelt guide, so it can
remain in the vehicle.
(See Fig. 1-g)
H. Remove the interior panel directly above the
driver side door sill by pulling it upwards,
releasing the retainer clips.
(See Fig. 1-h)
Fig. 1-h: Remove Interior Panel Above Driver
Side Door Sill
I. The driver side rear interior panel needs to be
removed. To remove, pull from the top of the
panel and pull away from the window. Work
your way around the panel to release all of the
retaining clips.
(See Fig. 1-i)
Fig. 1-g: Detach Small Plastic Trim
Fig. 1-i: Remove Driver Side Rear Interior Panel

DP/N: 007135v1.2, 2018-10-24
© 2018 Vortech Engineering, Inc.
All Rights Reserved, Intl. Copr. Secured. 4
K. Remove the two metal clips securing the insu-
lation block. Discard the insulation block and
two metal clips as they will not be reused.
(See Fig. 1-k)
REMOVE 2x
METAL CLIPS
Fig. 1-k: Remove Foam Insulation Block
1. PREPARATION AND REMOVAL, cont'd
J. Locate the driver side rear interior panel & lay
it down as shown. There is a foam insulation
block that needs to be removed to make space
for the fuel pump booster.
(See Fig. 1-j)
Fig. 1-j: Foam Insulation Block