Vox Technologies ROCKY-548TX User manual

ROCKY –548TX
Pentium™SBC
@Copyright 1997
All Rights Reserved.
Manual second edition Oct..1,1997
The information in this document is subject to change without prior notice in
order to improve reliability, design and function and does not represent a
commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special,
incidental, or consequential damages arising out of the use or inability to use
the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright. All
rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.
Trademarks
ROCKY-548TX is registered trademarks of Acquire Inc.,IBM PC is a
registered trademark of International Business Machines Corporation. Intel is
a registered trademark of Intel Corporation. AMI is registered trademarks of
American Megatrends, Inc. Other product names mentioned herein are used
for identification purposes only and may be trademarks and/or registered
trademarks of their respective companies.

1
Contents
1. Introduction ..........................................................3
1.1 Specifications..............................................................................4
1.2 What You Have...........................................................................5
2. Installation............................................................6
2.1 ROCKY-548TX's Layout ..............................................................6
2.2 Unpacking...................................................................................8
2.3 Setting the CPU of ROCKY-548TX.............................................. 9
2.4 System Memory DRAM..............................................................11
2.5 Watch-Dog Timer......................................................................12
2.6 DiskOnChip™Flash Disk ............................................................12
2.7 Clear CMOS Setup....................................................................14
2.8 Battery Backup for CMOS Setup ...............................................14
3. Connection.........................................................15
3.1 Floppy Disk Drive Connector......................................................15
3.2 PCI E-IDE Disk Drive Connector................................................16
3.3 Parallel Port...............................................................................17
3.4 Serial Ports................................................................................17
3.5 Keyboard Connector..................................................................18

2
3.6 External Switches and Indicators ...............................................18
3.7 External Speaker .......................................................................19
3.8 PS/2 Mouse 6-Pin Mini-DIN Connector ......................................19
3.9 External Battery Connector .......................................................20
3.10 USB Port Connector ..................................................................20
3.11 IrDA Infrared Interface Port .......................................................20
3.12 Fan Connector ..........................................................................21
3.13 Chassis Open Alarm Connector ................................................22
3.14 +5V Standby Connector for ATX Power Supply .........................22
3.15 ATX Power Switch / Soft Power Switch Connector .....................23
4. AMI BIOS Setup.................................................24
4.1 Getting Start..............................................................................24
4.2 Standard CMOS Setup ..............................................................25
4.3 Advanced CMOS Setup.............................................................26
4.4 Advanced Chipset Setup............................................................27
4.5 Peripheral Setup .......................................................................28
4.6 Power Management Setup.........................................................29
4.7 PCI / PLUG AND PLAY Setup....................................................30
4.8 Hardware Monitor Setup ……………………………………………31
5. E2Key Function..................................................32
Appendix A. Watch-Dog Timer..............................34

3
1
Introduction
Welcome to the ROCKY-548TX Pentium™Single Board
Computer. The ROCKY-548TX board is an ISA/PCI form factor
board, which comes equipped with high performance Pentium
CPU and advanced high performance multi-mode I/O, designed
for the system manufacturers, integrators, or VARs that want to
provide all the performance, reliability, and quality at a
reasonable price.
This board built-in DiskOnChip™(DOC) Flash Disk for embedded
application. The DOC Flash Disk is 100% compatible to hard
disk. User can use any DOS command without any extra
software utility. The DOC currently is available from 2MB to
72MB. There also have PROMDISK-Chip™can be used in the
same DOC socket as an alternative solution.
An advanced high performance super AT I/O chip –Winbond
W83977TF is used in the ROCKY-548TX board. Both on-chip
UARTs are compatible with the NS16C550. The parallel port and
IDE interface are compatible with IBM PC/AT and XT
architecture's.
In addition, the ROCKY-548TX provides four 72-pin SIMM
sockets and one 168-pin DIMM socket for its on-board DRAM.
The RAM module accepts 1MB, 2MB, 4MB, 8MB, 16MB, 32MB,
And 64MB. So,the total on-board memory can be configured
from 2MB to 256MB.
ROCKY-548TX uses the advanced INTEL Chipset,430TX
which is 100% ISA/PCI compatible chipset.with PCI 2.1
standard.
1.1 Specifications :

4
The ROCKY-548TX Pentium Single Board Computer provides the
following specification:
•CPU : Pentium™/MMX up to 233Mhz, AMD K5/K6 processor,
Cyrix 6x86 processor
•Bus : ISA bus and PCI 32-bit local bus,PCI 2.1 standard
•DMA channels : 7
•Interrupt levels : 15
•Chipset : Intel 430TX
•Real-time clock/calendar : in 430TX chipset, backup by industrial
Li-battery,3V/850mAH. .
•RAM memory : 2MB to 256MB,SDRAM,EDO and standard DRAM
supported
•Second Cache memory : 512KB Pipelined Burst SRAM on board
•Ultra DMA/33 IDE Interface : up to four PCI Enhance IDE hard
drives. The Ultra DMA/33 IDE can handle data transfer up to
33MB/s. The best of all is that is new technology is compatible with
existing ATA-2 IDE specifications. So there is no need to do any
change for customer’s current accessory.
•Floppy disk drive interface : two 2.88 MB, 1.44MB, 1.2MB, 720KB,
or 360KB floppy disk drives.
•Two high speed Series ports : NS16C550 compatible UARTs
•Bi-directional Parallel Port
•IrDA port : Support Serial Infrared(SIR) and Amplitude Shift
Keyed IR(ASKIR) interface.
•USB port : Support two USB ports for future expansion.
•Watch-dog timer : can be set by 1,2,10,20,110 or 220 seconds
period. Reset or NMI was generated when CPU did not periodically
trigger the timer. Your program use hex 043 and 443 to control the
watch-dog and generate a system reset.

5
•Flash Disk - DiskOnChip™:or PROMDISK-Chip™: The Flash Disk
provide 100% compatible with hard disk. The built-in TrueFFS
Transparent Flash Block Management and Space Reclamation will
let customer to use the Flash Disk with DOS command, no need any
extra software utility.
•Keyboard connector
•Mouse : PS/2 Mouse Port on-board.
•Power Consumption : +5V @ 4.0A
( Pentium/MMX-200,16MB EDO RAM)
+12V @ 70mA , -12V@20mA
•Operating Temperature : 0°~ 55°C ( CPU needs Cooler)
1.2 What You Have
In addition to this User's Manual, the ROCKY-548TX package
includes the following items:
•ROCKY-548TX Pentium Single Board Computer
•RS-232 Cable
•FDD/HDD Cable
•6-pin Mini-Din to 5-pin Din Keyboard Adapter Cable
If any of these items is missing or damaged, contact the dealer
from whom you purchased the product. Save the shipping
materials and carton in case you want to ship or store the
product in the future.

6
2
Installation
This chapter describes how to install the ROCKY-548TX. At first,
the layout of ROCKY-548TX is shown, and the unpacking
information that you should be careful is described. The
jumpers and switches setting for the ROCKY-548TX's
configuration, such as CPU type selection, system clock setting,
and watch dog timer, are also included.
2.1 ROCKY-548TX's Layout
< reference next page >

7
2.2 Unpacking

8
Your ROCKY-548TX Single Board Computer contains sensitive
electronic components that can be easily damaged by static
electricity.
In this section, we describe the precautions you should take
while unpacking, as well as during installation. It is very
important that the instructions be followed correctly, to avoid
static damage, and to successfully install the board.
The system board should be done on a grounded anti-static mat.
The operator should be wearing an anti-static wristband,
grounded at the same point as the anti-static mat.
Inspect the cardboard carton for obvious damage. Shipping and
handling may cause damage to your board. Be sure there are no
shipping and handing damages on the board before processing.
After opening the cardboard carton, exact the system board and
place it only on a grounded anti-static surface component side
up.
Again inspect the board for damage. Press down on all the
socketed IC's to make sure that they are properly seated.
Do this only with the board place on a firm flat surface.
Note : DO NOT APPLY POWER TO THE BOARD IF IT HAS
BEEN DAMAGED.
You are now ready to install your ROCKY-548TX Single Board
Computer.