Voxx Pursuit PRO9556Z User manual

1
2
3
4
1
2
3
4
5
6
1
2
3
4
14 Green/Orange Tach Input
13 Black/Yellow Pulse During Crank Output (-)
12 Green/Yellow Glow Plug Input (+)
11 Black/Red Pulse AŌer Shutdown Output (-)
10 Dk. Blue Trunk Output (-)
9 Black/Blue Factory Disarm Output (-)
8 Brown/Black Brake Input (+)
7 Black/Lt. GreenFactory Arm Output (-)
6 Dk. Blue/Black External AcƟvaƟon Input (-)
5 Lt. Blue Remote Start Status Output (-)
4 GreenUnlock Output (-)
3 Gray/Black Hood Input (-)
2 Red Lock Output (-)
1 Black/White Horn Output (-)
14 Pin Main Input/Output
4 Red BaƩery 12V (+)
3 Blue Data TX
2Black Ground (-)
1White Data RX
DBI
4 Red BaƩery 12V (+)
3 Black Ground (-)
2White Data RX
1Blue Data TX
CarLink
6 Empty Empty
5 Blue LED (-)
4 Red Valet Switch
3 Black Ground (-)
2 GreenData RX
1 Pink BaƩery 12V (+)
Antenna
1 Yellow Starter Output (+)
2 GreenIgniƟon 2 Output (+)
3 Red BaƩery 12VInput (+)
4 Red/White BaƩery 12VInput (+)
5 Purple Accessory Output (+)
6 Blue IgniƟon Input / Output (+)
6 Pin RS Harness
P
P
1 White Parking Light (30) Output
2 White/Red Parking Light (87)Input
3 Yellow/Black IgniƟon Output For Alarm (+)
4 Black Ground Input (-)
4 Pin Light
P
Replacement Part #4120463
Replacement Part #4120467
Replacement Part #4120465
Replacement Part #4120476
Replacement Part #4360847
Not Included
Not Included
VOXX
1 2
3
5
7
9
11
13
4
6
8
10
12
14
1 3
2 4
1 3 5
246
Replacement Part #183BPR
Replacement Part #4180070
PRO9556Z
Remote Start
System Layout
Important Update
The default Data Port Protocol of this system is ADS. If using an
FLCAN or other external integraon module be sure to choose
iDatalink 2-Way when ashing.
This system will also support DBI. This will require programming
Feature Bank 2, Feature 18 to DBI.
2020 Voxx Electronics. All Rights Reserved.
For Complete Installaon Guide and Technical Support Visit www.voxxuniversity.com. Or Call 1-800-225-6074

PRO9556Z
Remote Start w/Keyless
Quick Installaon Guide
For Complete Installaon Guide and Technical Support Visit
www.voxxuniversity.com
Or Call
1-800-225-6074
Nocaons
1 Run�me Expired
2 Remote Shutdown
3 Brake On
4 Manual Mode
5 Hood Open
6 Low / No Tach
7 Tach Programming
8 High Tach
1 Chirp 2 Chirp
3 Chirp 4 Chirp 5 Chirp 6 Chirp
1 Lock / Unlock Funcon 500ms 3.5sec 500ms L, DBL UL DBL L, 500ms UL DBL L, DBL UL 500ms L, 350ms UL
2 Accessory Lock NA
3 Accessory Unlock NA
4 Exterior Illuminaon NA
5 Auto Relock NA
6 Auto Arming NA
7 Nocaon Sound NA
8 Horn Timing 16ms 30ms
40ms 50ms 10ms
9 Valet Override Method NA
10 Driver Priority Unlock NA
11 Silent Choice OFF From Transmier OEM Style
12 Park Light / Trunk Swap NA
13 AUX Ch. 4 NA
14 AUX Ch. 5 NA
15 AUX Ch. 6 NA
16 AUX Ch. 7 NA
17 Security Prole OFF OEM Security W/ OEM Remote Start
18 Data Port Protocol ADS DBI
1 Chirp 2 Chirp
3 Chirp 4 chirp 5 Chirp 6 Chirp
1 Defrost Output NA
2 RS Start Nocaon ON OFF
3 RS Runme 15min 20min 45min 60min 5min 10min
4 RS Parking Lights Steady Flashing
5 Engine Conrmaon Tach Voltage
Data Hybrid
6 Voltage Level >0.5v B4 Start <0.5v B4 Start
7 Ignion 2 Output Ignion Accessory Start
8 Ignion 3 Output N/A
9 Accessory Output Accessory Ignion Start
10 Transmission
NA
11 Max Crank Time 0.8sec 1.0sec
1.5sec 2.0sec 3.0sec 4.0sec
12 Diesel Delay OFF Diesel 5 Diesel 10
Diesel 15 Diesel 20 Diesel 30
13 Temperature Start NA
14 Crank Duraon Averaging Preset
15 RS Shock Override NA
16 Turbo Timer NA
17 Start Acvaon Two Press One Press
Three Press
18 RS Lock Funcon No Change UL Before L Aer
UL Before Start Lock Aer Start
19 Factory Disarm Output Single Pulse 350ms 500ms 800ms Same As Bank 2, F1
20 Pul se During Crank During Crank GWR Ignion Accessory
21 Factory Arm Output Aer Start GWR Ignion Accessory Start
22 Pul se Aer Shutdown Aer Shutdown GWR Ignion Accessory Start
23 Addional Unlock Pulse No Pulse IGN, ACC, GWR IGN,ACC,GWR,PASD
Features
Feature Bank 2
Opons
Features
Feature Bank 3
Opons
Remote Start
If the remote start fails to start the vehicle, the system will ash the vehicle parking
lights to indicate the cause.
The Feature Banks below can also be programmed using the FlashLogic Weblink.
Please visit www.FlashLogic.com for more detail.
2020 Voxx Electronics. All Rights Reserved.REV. B
Chirp Delete
System ARM/DISARM chirps can be toggled ON or OFF without entering the Feature
Bank programming.
1. Turn the ignion key ON/OFF.
2. Press and release the valet buon three (3) mes.
The system will respond with one (1) chirp for ON and two (2) Chirps for OFF. This
feature will not aect alarm trigger or programming.
User Programmable LED
System LED nocaons can be turned ON or OFF without entering Feature Bank
programming.
1. Turn the ignion key ON/OFF, ON/OFF.
2. Press and hold valet buon for ve (5) seconds.
The LED will ash one (1) me for ON, two (2) mes for OFF. This feature will not aect
LED ash during programming.
OEM Security
This system can provide OEM level security. The system will monitor and trigger by the
analog hood input and all entry zone inputs from the FLCAN or other integraon modules.
When an entry zone is detected the system will beep the vehicle horn and ash the parking
lights. This feature must be acvated in Feature Bank 2, Feature 17.
Operaon
To arm the system, press lock buon.
To disarm the system, press unlock buon.
Valet Override Procedure
To disarm the system without the use of a remote, turn the ignion key to ON and press
the valet buon one (1) me.
Important Update
The default Data Port Protocol of this system is ADS. If using an
FLCAN or other external integraon module be sure to choose
iDatalink 2-Way when ashing.
This system will also support DBI. This will require programming
Feature Bank 2, Feature 18 to DBI.
Feature Programming
Remote Programming
Tach Programming
The PRO9556Z includes two (2) programmed remotes. If required, addional remotes
can be programmed to the system. Remote Programming is located in Feature Bank 1. To
enter Remote Auto Programming:
1. Turn the ignion key to the ON posion.
2. Press and release the valet buon three (3) mes. System will beep and ash the
parking lights one (1) me.
Press the lock buon on each remote. The system will beep one (1) mes to indicate the
remote has been programmed.
Data Protocol Selecon
The PRO9556Z Feature Banks can be programmed by using the valet buon and remote.
To enter Feature Bank programming:
1. Turn the ignion to the ON posion.
2. Press and release the valet buon three (3) mes. The system will beep and ash
the parking lights one (1) me for Feature Bank 1, Remote Programming.
3. Cycle the ignion key OFF/ON. The system will beep and ash parking lights two (2)
mes for Feature Bank 2.
4. Press the valet buon to cycle features. The LED will ash to display feature number.
5. Press the lock buon to cycle opons. The s`ystem will beep to indicate opon
number.
6. Cycle THE ignion key OFF/ON. The system will beep and ash parking lights three
(3) mes for Feature Bank 3.
7. Press the valet buon to cycle features. The LED will ash to display feature number.
8. Press the lock buon to cycle opons. The system will beep to indicate the opon
number.
The installer must manually congure the Engine Conrmaon method in Feature Bank
3, Feature 5. The default method is “Tach”. When using the default “Tach” method, the
vehicle tach rate must be programmed. To enter tach rate programming:
1. Turn the ignion key to the ON posion.
2. Press and release the valet buon three (3) mes.
3. Turn the ignion key to OFF.
4. Press and hold the valet buon.
5. While holding the valet buon, start the engine using the key.
6. Hold the valet buon for approximately ten (10) seconds. If connected to the vehicle
Tach source, the system will ash the parking lights one (1) me every second.
7. Release the valet buon. The system will turn on the parking lights for two (2)
seconds to indicate the tach rate is programmed.
The tach rate can also be programmed without the use of a valet buon. This is helpful
when using the OEM remote of CarLink system to control this module. To program the
tach rate without a valet buon:
1. Turn the ignion key to the ON posion and start the engine.
2. Wait for Engine RPM to lower to a normal idle.
3. Press and hold the vehicle’s brake pedal.
4. Press the LOCK buon on the OEM remote or the Carlink App.
Note: Programming tach signal via OEM or Telemacs control is only available on
Firmware v1.47 or Higher.
The default data port protocol of this model is ADS (iDatalink 2-Way). This model is
capable of detecng the correct data port protocol (ADS or DBI) and automacally
conguring Feature Bank 2; Feature 18. To inialize the detecon procedure:
1. Press and hold the valet buon.
2. Cycle the vehicle’s Ignion ON/OFF two (2) mes.
3. Release the valet buon.
The system will automacally detect and set the correct data port protocol, ADS or DBI.
Note: This feature is only available on module rmware v2.0 or higher.