VSS Nederland SUPREME IMAGE VCD-328IR User manual

45.8
1/3” Sony Super HAD High/Standard-Resolution Color CCD
600TVL Hi-Resolution, 350TVL Std-Resolution
Built-in 4mm F2.0 Fixed Lens
- Option: 2.9mm, 6.0mm
Auto Switching IR LED control by photocell
- IR LED: 30pcs
Smart IR : It prevents IR saturation
2D-Digital Noise Reduction
Dead Pixel Compensation
3-Axis Gimbal Bracket
Power: DC12V
94.80
Ø90
Ø117
Max. 90% RH
VBS 1.0 Vp
- p (75 Ω Load)
0Lux (IR LED On)
Internal
More than 48dB (AGC Off)
-10 ~ +50-
DC12V ± 10% ±
1/3" Interline transfer type color CCD (Sony)
Power
Consumption
Power Supply(*)
Scanning Frequency
Operational Humidity
PALNTSCITEM
(*) Use regulated & specified power supply.
15.625KHz(H), 50Hz(V)
625 Lines 2:1 Interlace
1/50~1/100,000 sec1/60~1/100,000 sec
15.734KHz(H), 59.94Hz(V)
525 Lines 2:1 Interlace
Video Output
White Balance
Min. Illumination
Lens
Sync. System
S/N Ratio
Shutter Speed
Resolution
Scanning System
Effective
Pixels
Hi-Res
Std-Res
Image Sensor
Dimensions
Operating Temp.
ATW
600TVL(Hi-Res), 350TVL(Std-Res)
Std. f=4mm F2.0 Lens (Option: 2.9mm, 6.0mm)
Max.: 350mA/DC12V (IR-LED On)
Max.: 380mA/DC12V (IR-LED On)
High-Res.
Standard-Res.
510H x 492V (250K Pixels) 500H x 582V (290K Pixels)
768H x 494V (380K Pixels) 752H x 582V (440K Pixels)
117mm (Dome: 90)95mm
INSTRUCTION MANUAL
SUPREME IMAGE
Video Surveillance Camera
e
High Resolution DNR Smart IR
Color Dome Camera
igh Resolution DNR Smart IR
mart IR
mart IR
solution DNR
C
l
D
C
VCD-328IR
VSS Nederland B.V. - Telfordstraat 11m - 8013 RL Zwolle - Tel.: [phone] - Fax: [phone] - E-mail: [email protected]
VSS Nederland
Video Systems

Tilt (90 )
Rotation (352 )
Pan(350 )
1. Rotation: Adjusting the rotation to
desired angle by hand.
2. Tilt: Adjusting the tilt to move up
and down by hand.
3. Pan: Adjusting the pan to turn
right and left by hand.
Installation & Adjustment
Installation
If the “Photocell” is blocked by the dome cover ring,
rotate and reassemble the upper part of the gimbal
for the “Photocell” to be shown.
1. Open the dome cover ring from the dome base with coins.
2. There are three mounting holes on the dome base so that you
can install the dome unit in any place such as ceiling, wall and etc.
3. Use the mounting screws to affix the dome base to a sturdy surface.
4. Connect the video & power cable to camera. Please check below
points before connection.
> Power supply
Adaptor: 800mA/DC12V
To aviod fire or shoct hazard, must be use a UL listed power supply
> Monitor Impedance
Set the impedance switch to 75Ωstandard position.
When monitor is set to high impedance mode, the picture may
become blurred.
In this case, check the switch position of monitor impedance.
5. Adjusts the camera viewing angle and then cover the dome cover
ring to the dome base.
3-Axis Gimbal Adjustment
To avoid smear, do not expose the camera directly
to a strong light source such as the sun or spot light.
Gimbal hook
Photocell
e
VSS Nederland B.V. - Telfordstraat 11m - 8013 RL Zwolle - Tel.: [phone] - Fax: [phone] - E-mail: [email protected]