VSS Nederland VSZ-1050-HD User manual

VSS Nederland B.V.
VSS Nederland B.V.
8013 RL Zwolle
T.038-4289420
www.vssnederland.nl

CAUTION :TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with an arrowhead symbol
within an equilateral triangle is intended to alert
the user to the presence of uninsulated
dangerous voltage within the producrs enclosure
that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying
the product.
FCC WARING -This equipment may generate or use
radio frequency energy. Changes or modifications to
this equipment may cause harmful interference unless
the modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this
equipment � an unauthorized change or modmcation is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with
the limits fora Class A digltal device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
wlth the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference
in which case the user will be required to correct the
interference at his own expense.
A suitable conduit entries, knock-outs or glands shall
be provided in the cable entries of this product in the
end use.
-Holes in metal, through which insulated wires pass,
shall have smooth well rounded surfaces or shall
be provided with brushings.
WARNING -Do not install this equipment in a confined
space such as a bookcase or similar unit.
WARNING -Wiring methods shall be in accordance with
the National Electric Code, ANSI/NFPA 70.
WARNING -This is a class A product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take adequate
measures.
WARNING -To reduce a risk of fire or electric shock, do
not expose this product to rain or moisture.
CAUTION -This installation should be made by a qualified
service personrel and should conform to all local codes.
CAUTION -To avoid electrocal shock, do not open the
cabinet. Refer servicing to qualified personnel only.
CAUTION -The apparatus should not be exposed to
water (dripping or splashing) and no objects filled with
liquids, such as vases, should be placed on the apparatus.
-
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol
is attached to a product it means the product
is covered by the European Directive
2002/96/EC
2. All electrical and electronic products should
be disposed of separately from the municipal
waste stream via designated collection facillties
appointed by the government or the local
authorities
3. The correct disposal of your old appliance
will help prevent potential negative conse-
quences for the environment and human
health
4. For more detailed information about disposal
of your old appliance, please contact your
city office, waste disposal service or the shop
where you purchased the product.
To disconnect power from the mains, pull out the main
card plug. When installing the product, ensure that the
plug is easily accessible.
03

1. Read these instructions -All these safety and operating
instructions should be read before the product is operated.
2. Keep these instructions -The safety, operating and user
instructions should be retained tor future reference.
3. Heed all warnings -All warnings on the product and in
the operating instructions should be adhered to.
4. Follow all instructions -All operating and user instructions
should be followed.
7. Do not block any ventilation openings. lnstall in
accordance with the manufacturer's instructions.
Slots and openings in the cabinet are provided tor
ventilation, to ensure reliable operation of the product,
and to protect lt trom overheating. The openings should
never be blocked by placing the product on a bed, sofa,
rug or other similar surface. This product should not
be placed in a built-in installation such as a bookcase
or rack unless proper ventilation is provided and the
manufacturer's instructions have been adhered to.
5. Do not use this apparatus near water _ For example : 8. Do not install near any heat sources such as
near a bath tub, wash bowl, kitchen sink, laundry tub, radiators, heat registers, stoves, or other apparatus
in a wet basement, near a swimming pool, etc. (including amplifiers) that produce heat.
6. Clean only with dry cloth -Unplug this product trom
the wall outlet before cleaning. Do not use liquid cleaners.
04
9. Proleet the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
1
O. Only use attachments/accessories specified by the
manufacturer.
11. Unplug this apparatus during lightning storms or
when unused for long periods of time.
12. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or
plug is damaged, liquid has been spilled or objects
have tallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
05

06
FEATURES ...................................................... 7P SPECIAL FUNCTION .............................. 26P
PACKAGE COMPONENTS ............................... 8P DISPLAY .............................................. 28P
SYSTEM CONFIGURATION .............................. gp SPECIFICATION ........... ................. ............ 30P
PART NAMES AND FUNCTIONS ..................... 10P DRAWING ................................................ 33P
CONNECTIONS .............................. ............... 12P TROUBLESHOOTING ................................ 34P
EXTERNAL DEVICE CONNECTIONS.... ............ 13P
VIDEO OUT .... ............ ................. .................. 14P
MENU OPERATION ........................................ 15P
MAIN MENU .................................................. 16P
FOCUS ...................................................... 17P
EXPOSURE .............. ................. ................ 18P
WHITE BALANCE ...................................... 21 p
IMAGE ...................................................... 22P
INTELLIGENCE ................. ................. ....... 24P
Features
•1/3" Panasonic CMOS sensor
• x10 Optical Zoom
• Full HD Resolution
• Day & Night(ICR)
• Wide Dynamic Range
• Digital Noise Reduction(2D+3D)
•Privacy Mask Function
• On Screen Display
• Intelligent Motion Detection
• Multi Protocol
07

[Opllona . 1 Remote Controller]
1
DC 12VCABLE MANUAL
CAMERA
08
RS485
DVR
RS485 t
SDEO
TV Monijor
09

10
[ 1
l Camera installation bracket
The braket can be fixed at the top or bottom of the
camera.
[1] [2] [3]
[9] [10]
i;((l-tl/--[4]
,-------,lltll--[5]
-IH-II-- [
8]
'-----IH-11--[6]
-1ttlr-[7]
[11]
[ 1
l OSD /Zoom/ Focus control
[2) DIGITAL Out
[3) ANALOG Out
[4) HD-SDI
[5) EX-SDI
[61 CVBS
[7) HD-TV1
[8) AD Key
1: GND
2: AD-key
3:GND
[9) Power LED
[10) Control Terminal
1: RS-485 ( +)
2: RS-485 (-)
3: Motion Detection Out
4: Ground
5: Day&Night Input (Low : Night, High : Day)
6: Ground
[11) Power:DC12V

12
3
To monitor's Video Input
or Camera Input
Basic connection
The peripheral devices (DVR, monitor, lens, etc), DC adaptor
and cables are not supplied.
1. Connecting the monitor.
Make the video signal connection between the camera and the
monitor or time lapse monitor or DVR.
2. Use a commercially available DC12V adaptor.
Connect an DC 12V power source to the DC 12V input terminal
on the back of the camera.
3. lnsert the plug of this power cord into a wall outlet.
The POWER indicator will light. Adjust the picture on the monitor
using the Brightness and Contrast controls etc.
RS-485 COMMUNICATION
Connect to an external controller of RS-485 format.
Motion Detection Out
When the motion detection function is working.
DC3.3V is outputed to OUT pin and GND pin.
Day & Night input
Day/Night mode of the camera can be switched by
signal trom
an external device.
To use this function, <DAY&NIGHT> setting of the
camera should be set to the < EXT>.
Note : Use a relay unit if the voltage or current of the
connected device exceeds the ratings.
13

14
DIGITAL OUT
Select HD-SDI and EX-SDI video out
by switch setting.
,/ ,,a
! C ■=
\ HD-TV1 H I
AD:v
\��ALOGOUT
' - 00000 @@
.M�D� 0 0
DDND DC12V
ANALOG OUT
0
Select CVBS and TV1 video out
by switch setting.
This camera utilizes an on-screen user MENU. To set items
on the menu, use the following buttons on the side panel.
(-;;- i
\ , =
',,,, W § AD KEY
----- HD-TV1
00000 @@
0 0
.M�D�
0 0
DDND DC12V
• T Tele(Up) button : Zoom in, Tele (Moves the cursor
upwards. Use this button to select an item or
adjust the parameters.)
Tw Wide(Down) button: Zoom out, Wide (Moves the
cursor downwards. Use this button to select an
item or ad just the parameters.)
Far(Right) button : Ad just focus in Manual Mode
(Moves the cursor to the right. Use this button to
select or adjust the parameters of the selected
item. The parameter changes each time this
button is pressed.)
◄Near(Left) button : Adjust focus in Manual Mode
N
Moves the cursor to the left. Use this button to
select or adjust the parameters of the selected
item. The parameter changes each time this
button is pressed.)
Set button : Executes selections and displays a
submenu for an item with the QJ mark.
15

16
Camera menu is subject to be changed without prior notice to upgrade and quality increase and we may use
slip sheet for the change.
Please check the camera version and the slip sheet if the camera menu and this manual menu is not matched.
MAIN MENU
MENU
i URE
j
:tJ B A L
j
INTE L L IGENCE J
SPECI A L FUNC J
DISP LAY J
[EXIT] [SAVE] [DFLT]
Functions can be setup using "Menu Key Command"
of Visca protocol.
The menu consists of the "Main Menu" and "Sub Menu".
The main menu is displayed where 7 camera functions
can be selected.
To the push of each main menu selection, the sub-menu
is displayed
lf you want save the menu, select [SAVE]
lf you want not save the menu, select [EXIT]
(After select, Power off-+ on)
lf you want default the menu, select [DFL T]
FOCUS
MENU FOCUS
FOCUS J MODE
EXPOSURE J DISTANCE
WHITE BAL J ZOOM SPEED
IM AGE J LENS REFRESH
INTE L L IGENCE J E.ZOOM
SPECIA L FUNC J ZOOM PRESET
DISP LAY J
[EXIT] [SAVE] [DFLT] [B A CK] [SAVE]
+MODE : Select auto focus mode
► AUTO, ONE PUSH, MANUAL
AUTO
1.0m
=7
ONE PUSH J
OFF
J
[DFLT]
+DISTANCE : Select minimum distance in focus between camera and object.
► 0.1 / 1.0 / 3.0 / 5.0 / 10.0 m
ZOOM SPEED : Select Zoom Speed ► 0 (Slow) - 7 (Fast)
+LENS REFRESH : Lens origin calibrated automatically.
►ONE PUSH.J / ON (1 day -10 days)
+E.ZOOM : Select maximum digital zoom magnification.
►OFF / ON (max x2 -x19, x21, x23, x25, x28, x32)
ZOOM PRESET : Select zoom preset
►PRESET # : Select Zoom preset number (1 -5) ► MODE : OFF/ ON.J
I> ON.J : Adjust the Zoom Position
17

18
EXPOSURE
MENU EXPOSURE
FOCUS
J
MODE
EXPOSURE
J
AGC
WHITE BAL
J
SHUT SPEED
IMAGE
J
IRIS
INTELLIGENCE
J
DSS
SPECIAL FUNC
J
FLICKERLESS
DISPLAY
J
BRIGHTNESS
WDR/BLC
DAY&NIGHT
[EXIT] [SAVE] [DFLT] [BACK] [SAVE]
� MODE : Select Exposure Mode
►AUTO / IRIS.P / SHUT.P / MANUAL
� AGC : Select Auto Gain Control
AUTO
ON
OFF
OFF
8
OFF
J
[DFLT]
► OFF/ ON (AUTO, SHUT.P or IRIS.P Mode)
► 0 ~ 10 (MANUAL Mode)
� SHUT SPEED : Can be set in SHUT.P or MANUAL mode
* 60 I 50 fps mode ► x8, x4, x2, 1/60(50), 1/120(100), 1/250, 1/700, 1/1000, 1/1600, 1/2500,
1/5000, 1/7000, 1/10000, 1/30000 sec
*30 / 25 fps mode ► x4, x2, 1/30(25), 1/60(50), 1/120(100), 1/250, 1/700, 1/1000, 1/1600,
1/2500, 1/5000, 1/7000, 1/10000, 1/30000 sec
� IRIS : Iris level can be set in IRIS.Por MANUAL mode
► 0~20
� DSS : Select maximum DSS (Digital Slow Shutter)
*60 / 50 fps mode ► OFF/ x2, x4, x8
*30 / 25 fps mode ► OFF / x2, x4
� FLICKERLESS : Select Flicker less mode
► OFF / ON (remove screen flicker)
� BRIGHTNESS : Adjust brightness level
► 0(dark) ~ 20(bright) steps
� WDR/BLC: Select WDR(Wide Dynamic Range) or BLC(Back Light Compensation)
► WDR.J
[> WDR_WGT: Adjust WDR level.
► LOW, MID-LOW, MIDDLE, MID-HIGH, HIGH
* WDR doesn't work in Manual Exposure Mode and Shutter Priority Mode.
* When WDR on, CVBS output is disabled.
► BLC.J
[> POSITION : Adjust the window position
[> SIZE : Adjust the window size
* Can't use WDR and BLC at the same time.
(When WDR On, BLC is Off. And when BLC is On, WDR is Off)
* BLC doesn't work in Manual Exposure Mode.

20
*
DAY&NIGHT : Select Day&Night
►
MODE : AUTO/ EXT-IN / DAY/ NIGHT
AUTO
I> DELAY : 0 - 255 sec
I> THRS : Day ...... Night switching level in Auto Mode.
Switching in lower lux with higher threshold level.(0 - 28)
I> GAP : LOW, MID-LOW, MIDDLE, MID-HIGH, HIGH
Margin between Day -+Night switching level and Night -+Day switching level.
I> IR DETECTION : Setting IR Detection mode. (ON / OFF)
I> IR DET LEVEL : Setting IR Detection level.(LOW, MID-LOW, MIDDLE, MID-HIGH, HIGH)
I> BURST : OFF / ON
►
EXT-IN
I> DELAY : 0 - 255 sec
I> BURST : OFF / ON
I> POLARITY : External Input polarity (ACTIVE LOW/ ACTIVE HIGH)
►
NIGHT
I> BURST : OFF / ON
WHITE BALANCE
MENU WHITE BAL
FOCUS
J
MODE AUTO
EXPOSURE
J
RED GAIN
WHITE BAL
J
BLUE GAIN
IMAGE
J
CHROMA ===-10
INTELLIGENCE
J
SPECIAL FUNC
J
DISPLAY
J
[EXIT] [SAVE] [DFLT] [BACK] [SAVE] [DFLT]
AWB : Select WHITE BALANCE mode
AUTO/ ONE PUSH / MANUAL / INDOOR/ OUTDOOR
I> AUTO : Automatically adjusts color according to the available lighting.
I> ONE PUSH : lt is a fixed white balance mode that may be automatically readjusted only by pressing
ONE PUSH
I> MANUAL..J : Color can be corrected when the user increases or decreases
"RED GAIN" or "BLUE GAIN".
I> INDOOR : Set color temperature to be Indoor light (3700
°
K)
I> OUTDOOR : Set color temperature to be Outdoor light (5100
°
K)
RED GAIN : Adjust R gain value
►
0 - 20 steps
BLUE GAIN : Adjust B gain value ► 0 - 20 steps
CHROMA: Adjust CHROMA gain value
►
0 - 20 steps
21

22
IMAGE
MENU IMAGE
FOCUS
J
HLC
J
EXPOSURE
J
DNR MIDDLE
WHITE BAL
J
MIRROR OFF
IMAGE
J
SHARPNESS
7
INTELLIGENCE
J
ACE OFF
SPECIAL FUNC
J
DEFOG OFF
DISPLAY
J
FREEZE OFF
GAMMA 0.55
[EXIT] [SAVE] [DFLT] [BACK] [SAVE] [DFLT]
+ HLC : Select High Light Compensation.
When extremely bright light is projected to the camera masking is used on the portion to prevent partial
saturation on the monitor.
I> MODE : OFF/ ON / NIGHT
I> LEVEL : 0 ~ 20 steps
I> COLOR : 0 ~ 13 steps
+ DNR : Select Digital Noise Reduction
► AUTO/ OFF/ LOW/ MIDDLE / HIGH
+ MIRROR : Selecta flip mode
►
OFF/H/V/H&V
I> H : You can flip the picture horizontally on the screen
I> V : You can flip the picture vertically on the screen
I> H&V: You can flip the picture horizontally & vertically on the screen
IMAGE
+ SHARPNESS : Adjust sharpness level
► 0 ~ 10 steps
+ ACE : Select Digital WOR (Wide Dynamic Range)
► OFF/ LOW/ MIDDLE/ HIGH
+ DEFOG : Carry out defog function
► OFF /ON.J
I> MODE : AUTO/ MANUAL
I> LEVEL : LOW/ MIDDLE / HIGH
* Can't use DEFOG and ACE at the same time (When DEFOG is On, ACE is Off)
+ Freeze : Select real or still mode
► OFF/ON
+ GAMMA: Select GAMMA
► 0.45 / 0.55 / 0.65 / 0.75
23

24
INTELLIGENCE
MENU INTELLIGENCE
FOCUS
J
PRIVACY OFF
EXPOSURE
J
MOTION OFF
WHITE BAL
J
DIS OFF
IMAGE
J
INTELLIGENCE
J
SPECIAL FUNC
J
DISPLAY
J
[EXIT] [SAVE] [DFLT] [BACK] [SAVE] [DFLT]
+
PRIVACY : Hide an area you want to hide on the screen
OFF /ON.J
[> MASK#: Select mask area number (1 -24)
[> MODE : Mask enable or disable (OFF/ ON)
[> POSITION : Adjust the mask position
[> SIZE : Adjust the mask size
[> COLOR: Select mask color (0 -13)
[> TRANS : Select mask transparency level (0 - 4)
+ MOTION : When there is movement of the subject in the screen,
there will be an motion detection
OFF /ON.J
[>AREA#: Setting 3 areas(1-3) of motion detection
[> MODE : OFF/ ON (Limit and define areas of motion detection)
[> SENSITIVITY: Adjust sensitivity of MD (0 -20 steps)
More sensitive to setting to low step with sensitivity
[> POSITION : Adjust the Area position
[> SIZE : Adjust the Area size
[> INTERVAL :Select the alarm interval time (0 -255sec)
[> DWELL TIME : Select the duration time about changing MD mode (0 -255sec)
[> ZOOM PRESET: Select Motion Zoom Preset Mode and Position (OFF/ ON.J)
+ DIS : Select Digital Image Stabilizer mode
OFF /ON.J
[> RANGE: Setting the image compensation range. (10%, 20%, 30%)
[> FILTER : Setting the sensitivity to hold DIS function in worst case.(LOW, MIDDLE, HIGH)
[> AUTO C : Setting Auto Centering mode (OFF, HALF, FULL)
25

26
SPECIAL FUNC
MENU SPECIAL FUNC
FOCUS
J
DEFECT
J
EXPOSURE
J
IMAGE RANGE FULL
WHITE BAL
J
SYSTEM NTSC
IMAGE
J
HD FORMAT 1080p/30fps
INTELLIGENCE
J
COMM
J
SPECIAL FUNC
J
DISPLAY
J
[EXIT] [SAVE] [DFLT] [BACK] [SAVE] [DFLT]
+ DEFECT DET : Compensates tor bad pixels that may occur.
Occurs when the whole screen is in full black or if there is bad pixelation and it changes the THRS values
until the screen is fixed.
* When you use this function, you have to block the lens tor blocking lights into the lens.
+ IMAGE RANGE: Select image bit range. (Full : 100%, Compressed : 75%)
► FULL, COMP, USER..J
I> LEVEL : Select user mode level (0 ~ 32)
+ SYSTEM: Select NTSC(30/60fps) or PAL(25/50fps).
+ HD FORMAT: Select Digital output(1080p/30(25)fps, 1080p/60(50)fps, 720p/30(25)fps, 720p/60(50)fps)
+ COMM: Set up the camera ID, baudrate, protocol
I> ID : Select the camera ID
► 1 ~255
I> BAUD RATE : Select serial communication speed
► 2400 / 4800 / 9600 / 19200 / 38400 / 57600 / 115200bps
I> PROTOCOL : Select operating protocol
► VISCA/ PELCO-D / PELCO-P / UPDATE
2l

28
DISPLAY
MENU DISPLAY
FOCUS J DISP SEL ONJ
EXPOSURE J SET TITLE J
WHITE BAL J INIT SEL ONJ
IMAGE J SET INIT MSG J
INTELLIGENCE J LANGUAGE ENGLISH
SPECIAL FUNC J
DISPLAY J
[EXIT] [SAVE] [DFLT] [BACK] [SAVE] [DFLT]
� DISP SEL : Select display item.
► OFF /ON.J
[> ID : OFF/ ON
[> TITLE : OFF / ON
[> ZOOM RATIO : OFF/ ON
[> SYSTEM MSG : OFF/ ON (MD Alarm)
� SET TITLE : Select camera title menu (Text edit- max 40 characters)
� INIT SEL: Select display initial message.
► OFF /ON.J
[> ID : OFF/ ON [> BAUDRATE : OFF/ ON
[> PROTOCOL : OFF/ ON [> VERSION : OFF/ ON
[> INIT MSG : OFF/ ON
� SET INIT MSG : modify initial message. (Text edit- max 40 characters)
� LANGUAGE : Select language.
► English / Simplified Chinese/ Traditional Chinese/ Japanese
* Character Table of Text edit Mode
ABCDEFGHIJKLMN0PQRST
UVWXYZabcdefghi jklmn
opqrstuvwxyz,. (){}[]
0123456789*+-/=-!?"'
29

lmaae Sensor 1/3" Panasonic CMOS Sensor ZoomPreset 5 preset
Total Pixels 1,956(H) x 1,266M, 2.48M Pixels Exposure Mode/ AGC / Shui Speed/ Iris/ DSS / Flickerless / Brightness / WDR/BLC / D&N
Active oixels 1,944/Hl x 1,092M, 2.12M Pixels Mode Auto/ Iris. Priority / Shui. Priority / Manual
Scanning svstem Progressive Scan Gain Control(AGC) Off/ On
Svnc. Svstem lnternal Shutter Speed 1/30(25) -1/30,000 sec
Resolution Dioital : 1 OSOo/60150\fns 1 OSOo/30125\fns 720o/60150\fas 720nl'llll25\fns Iris O - 20 steps
Analoa : 7001VL Digital Slow Shutter(DSS) Off/ x2 / x4 V x8 : 60 or 50 fps mode only)
Min. illumination Color : 0.5 lux fNI : 0.1 lux Flickerless Off/ On
Color DSS: 0.002 lux BW DSS : 0.001 lux Brightness 0-20steps
Video Output HD : HD-TVi / HD-SDI / EX-SDI WDR/BLC OFF/ WOR/ BLC
Analoo SD : VBSlwithout WOR\ Day&Night Auto/ Day/ Night/ Ext-in
SIN Ratio more than 50dB IAGC offl White Baiance Auto/ One Push/ Manual / Indoor/ Outdoor
Lens"""' x10 Dav & Ninht Zoom Lens Image HLC / DNR / Mirror / Sharpness /ACE/ Defog / Freeze / Gamma
loom Ratio Ootical x1 O Diaital x32 Zoom HLC Off/ On/ Night Only
Focallenath f= 5.1mm- 51mm DNR Auto/ Off/ Low/ Middle/ High
Aoerture Ratio F1.6 /wide\ -F1.8 ltele\ Mirror Off/H/V/H&V
Angle of View (D, H, VJ Wide
1
68
°
1
540
1
31
°
Sharoness 0-10 steps
Tele
1
6.7
°
1
4.9"
1
4.Cl° ACE Off/ Low/ Middle/ Hiah
Focus Mode/ Distance /Zoom Speed/Lens Refresh / E.Zoom Defoo Off/ On (Auto/ Manuall
Mode Auto/ One Push/ Manual Freeze Off/ On
Distance 0.1 / 1.0/ 3.0/ 5.0/ 10.0 m Gamma 0.45 / 0.55 / 0.65 / 0.75
Zoom Speed O(Slow) -7/Fastl lntelligence Privacy/ Motion/ DIS
Lens Refresh One Push/ 1 -10Day Privacv Mask Off/ On (24 oointsl
E.Zoom Off/ MAX x2 -x32 MotionDetection Off/ On (3 points)
30
31

Diailal lmaae Stabilizer Off/ On
Soocial Func Defect/ lmaae Ranae / Svstem / HD Format/ EX-SDI/ COMM
Defect DET Off/ On
lmaae Ranae Full/ Camo. / User
SvstP.m NTSC/PAL
HD Fonmat 1080Di30125)tps / 1080o/60(50lfos / 720o/30(25lfos / 720o/60(50)tps
EX-SDI Off/ On
HD-lVI Off/ On
Comm 10:1-255
Baud Rate : 2400 / 4800 / 9600 / 19200 / 38400 / 57600 / 115200
Protocol : Pelco-P / Pelco-0 / VlSCA / Uodate
Display Disp Sel / Set îrtle / lnit Sel / Set lnit Msg / Language
Diso Sel (Off/ On) ID/ îrtle / Zoom Ratio/ Svstem Messaae
Setîille Text Edit
lnit Sel (Off/ On) ID/ Baud Rate / Protocol / Version / lnit. Messaae
SetlnitMsg Text Edit
Lanauaae Enalish / Simolified Chinese/ Traditional Chinese/ Jaoanese
Power Source 9Vto 15VDC
Power Consumotion 250mA
Powerlnout Connector
Video Output Connector
S1oraae Temoerature -20t -+60t /Humiditv: 0%RH -90%RHl
Operating Temperature -10t -+50t (Humidity: 0%RH -90%RH)
32
e e
1
-+-
1
e e
59
-
12
--------- -tl
68
100
33

lf !here are problems in operation, please reler to the items below.
lf the problem persists, please contact the agent you purchased this product trom.
Trouble shooting
• Nothing appears on the screen.
-Please check the power connection.
-Please check the video signal line connection.
• The video image is not clear.
-Please dean the lens with a clean cloth or brush.
-Please adjust that the screen is not exposed directly to a bright light.
-Please move the camera if necessarv.
• The screen is dark.
-Please adjust the contrast feature of the monitor.
-lf you have an intennediate device, set the 75 O /Hi-2 properly, and check the tenninals.
-Please adiust the briahtness level.
• The MOTION DETECTION function is not werking
-Please check if "MOTION DETECTION" mode is tumed on.
-Please check if the MD Sensitivity is too high.
-Please check the settina af the MD AREA.
• The WDR function is not werking
-Please check if the WOR Level is toa low.
-Please check if the AE Mode is set to MANUAL. The WOR doesn't work in MANUAL, Shutter priority
Exposure mode.
• Colors are not quite right.
-Please check if the camera is facing directly into sunlight or fluorescent light.
• The Day&Night function doesn't work.
-Please check if the AGC of EXPOSURE menu is set to OFF.
34
-The Auto Day&Night doesn't work inAGC OFF status.
35