VSS Nederland VCD-328 User manual

82.6
40
Ø85
Ø107
107mm (Dome: 85)82.6mm
Std. f=3.6mm F2.0 (Option: 2.9mm)
0.2Lux @F2.0
Max. 90% RH
VBS 1.0 Vp
- p (75 Ω Load)
Internal
More than 48dB (AGC Off)
-10~ +50-
DC12V ± 10% ±
1/3" Interline transfer type color CCD (Sony)
Power
Consumption
Power Supply(*)
Scanning Frequency
Operational Humidity
PALNTSCITEM
(*) Use regulated & specified power supply.
15.625KHz(H), 50Hz(V)
625 Lines 2:1 Interlace
1/50~1/100,000 sec1/60~1/100,000 sec
15.734KHz(H), 59.94Hz(V)
525 Lines 2:1 Interlace
Video Output
White Balance
Min. Illumination
Lens
Sync. System
S/N Ratio
Shutter Speed
Resolution
Scanning System
Effective
Pixels
Hi-Res
Std-Res
Image Sensor
Dimensions
Operating Temp.
ATW
600TVL(Hi-Res), 350TVL(Std-Res)
Max.: 100mA/DC12V
Max.: 130mA/DC12V
High-Res.
Standard-Res.
510H x 492V (250K Pixels) 500H x 582V (290K Pixels)
768H x 494V (380K Pixels) 752H x 582V (440K Pixels)
1/3” Sony Super HAD High/Standard-Resolution Color CCD
600TVL Hi-Resolution, 350TVL Std-Resolution
Built-in 4mm F2.0 Fixed Lens
- Option: 2.9mm
2D-Digital Noise Reduction
Dead Pixel Compensation
3-Axis Gimbal Bracket
Power: DC12V
INSTRUCTION MANUAL
SUPREME IMAGE
Video Surveillance Camera
e
High Resolution DNR Smart IR
Color Dome Camera
igh Resolution DNR Smart IR
mart IR
mart IR
solution DNR
C
l
D
C
e
VSS Nederland B.V. - Telfordstraat 11m - 8013 RL Zwolle - Tel.: [phone] - Fax: [phone] - E-mail: [email protected]
VSS Nederland
Video Systems VCD-328

Tilt (90 )
Rotation (352 )
Pan(333 )
1. Rotation: Adjusting the rotation to
desired angle by hand.
2. Tilt: Adjusting the tilt to move up
and down by hand.
3. Pan: Adjusting the pan to turn
right and left by hand.
Installation & Adjustment
To avoid smear, do not expose
the camera directly to a strong
light source such as the sun or
spot light.
1. Open the dome cover ring from the dome base with coins.
2. There are three mounting holes on the dome base so that you can install the dome unit in
any place such as ceiling, wall and etc.
3. Use the mounting screws to affix the dome base to a sturdy surface.
4. Connect the video & power cable to camera. Please check below points before connection.
> Power supply
Adaptor: 500mA/DC12V
To aviod fire or shoct hazard, must be use a UL listed power supply
> Monitor Impedance
Set the impedance switch to 75Ωstandard position. When monitor is set to high impedance
mode, the picture may become blurred. In this case, check the switch position of monitor impedance.
5. Adjusts the camera viewing angle and then cover the dome cover ring to the dome base.
Adjustment
e
VSS Nederland B.V. - Telfordstraat 11m - 8013 RL Zwolle - Tel.: [phone] - Fax: [phone] - E-mail: [email protected]