Vult Vorg User manual

VORG
build guide

VORG BUILD GUIDE
Thank you very much for acquiring the Vorg DIY kit. This
guide will walk you through the whole assembly process.
Before you start we recommend you to read the guide,
specially the Notes that some of the steps have.
Since this is an SMD kit, you need to be very careful when
you solder the components. Especially some of the small IC
components since you can create bridges and not see them
with a naked eye. Using a magnifying glass or a microscope
is highly advisable.

VORG BUILD GUIDE
Remember that by purchasing a DIY kit you are responsible
if your build fails. We cannot provide repair services for
failed builds. The main reason is that, depending on the
extent of the damage, the total cost you’ll end up paying
would be higher than buying the assembled module in the
rst place.
We want you to succeed. For that reason we tried to make
this guide as detailed as possible. We also provide you the
components organized to minimize the risk of mixing them
up.
Disclaimer

VORG BUILD GUIDE
This guide contains one page for each different component
you are gonna place. The components are organized
starting from the lower values. For example, 1kΩ resistors
are placed before the 2kΩ resistors.
At every step we have highlighted with RED the locations
where you need to place the components. The locations
marked with GREY are where you should have already
placed a component in a previous step.
How to use this guide
Place a
component
here
You should
have placed a
component here
at a previous step

VORG BUILD GUIDE
We hope you enjoy building your own Vorg and if you like it
share your results in social media.
Leonardo, Radost and Andrey

VORG BUILD GUIDE
ASSEMBLING THE MAIN BOARD

VORG BUILD GUIDE
Component: Resistor
Value: 220Ω
Quantity: 4
Designators: R15, R14, R17, R16

VORG BUILD GUIDE
Component: Resistor
Value: 1kΩ
Designators: R11, R26, R27
Quantity: 3

VORG BUILD GUIDE
Component: Resistor
Value: 1.8kΩ
Designators: R19, R4
Quantity: 2

VORG BUILD GUIDE
Component: Resistor
Value: 4.7kΩ
Designators: R2
Quantity: 1

VORG BUILD GUIDE
Component: Resistor
Value: 10kΩ
Designators: R9, R12, R10, R18, R13, R7, R8,
R20, R22, R23, R24, R25,
Quantity: 12

VORG BUILD GUIDE
Component: Resistor
Value: 22kΩ
Designators: R21
Quantity: 1

VORG BUILD GUIDE
Component: Resistor
Value: 100kΩ
Designators: R1, R3, R5
Quantity: 3

VORG BUILD GUIDE
Component: Resistor
Value: 470kΩ
Designators: R6
Quantity: 1

VORG BUILD GUIDE
Component: Capacitor
Value: 1nF
Designators: C4, C5
Quantity: 2

VORG BUILD GUIDE
Component: Capacitor
Value: 4.7nF
Designators: C1
Quantity: 1

VORG BUILD GUIDE
Component: Capacitor
Value: 100nF
Designators: C7, C8, C9, C10, C12, C13, C14,
C15
Quantity: 8

VORG BUILD GUIDE
Component: LED
Value: -
Designators: LED1, LED2
Notes: The LEDs must be placed reversely.
The actual placement does not matter as long as the
marks are on the opposite side.
Look for the mark at the bottom of the LED.
Quantity: 2
LED2 LED2
LED1 LED1
LED2
LED1
LED2
LED1
OK OK ERROR ERROR

VORG BUILD GUIDE
Component: Transistor pair
Value: BCM857
Designators: Q1
Notes: Look for the mark in one of the
corners of the package. Make sure it matches
the orientation. The mark is tiny, you have to
use a magnifying glass.
Quantity: 1
Q1 Q1
OK ERROR

VORG BUILD GUIDE
Component: Ferrite
Value: -
Designators: F1, F2
Quantity: 2