Vxl Itona E series User manual

1
Itona E Series
Hardware User’s Guide
VXL Instruments Ltd,
NO.17, House of Excellence,
Electronics City,
Hosur Road,
Bangalore – 560 100, INDIA
www.vxl.net

VXL Instruments Ltd. Itona E series Hardware User’s Guide
Copyright and Trademark Notices 2
Copyright and Trademark notices
ALL RIGHTS RESERVED.
Information in this document is subject to change without notice and does not represent a commitment
on the part of the manufacturer. No part of this guide may be reproduced or transmitted in any form or
means, electronic or mechanical, including photocopying and recording, for any purpose, without the
express written permission of the manufacturer.
Every effort has been made to make this guide as complete and as accurate as possible, but no
warranty or fitness is implied. The authors and the publisher shall have neither responsibility nor liability
to any person or entity with respect to loss or damages arising from the use of information contained in
this guide. This disclaimer does not apply in countries where such provisions are inconsistent with local
law.
All Trademarks are acknowledged.
Document Number: 600 0110 529 36 Rev A00
First Edition: 17th November 2010

VXL Instruments Ltd. Itona E series Hardware User’s Guide
FCC statement and Warning 3
Federal Communication Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment Off and On, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Re-orient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio / television technician for help.
•Each Thin Client is marked with a FCC logo on the label. The full information of the
associated label is as follows:
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
Warning
•DO NOT open enclosure, Hazard voltages present inside equipment.
•Ensure that all expansion slots (on the back or side of the computer) are covered with metal
retaining brackets, and tightly attached to the computer cabinet.
•Only equipment certified to comply with Class B (computer input/output devices, terminals, printer’s
etc.) should be attached to this equipment, and must have shielded interface cables.
•Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment.
•This equipment should not be used in Electro-medical applications.
•There are no user serviceable parts inside. DO NOT open enclosure, Hazard voltages present
inside equipment. DO NOT disassemble the equipment as this can nullify your warranty
•DO NOT operate this equipment in corrosive or explosive atmosphere.
•DO NOT operate this equipment outside specified temperature limits.
•This equipment must be earthed.
•The AC socket outlet shall be installed near the equipment and shall be easily accessible.
•Sound Power Level is less than 60dB (A), when measured according to ISO 7779.

VXL Instruments Ltd. Itona E series Hardware User’s Guide
Preface 4
Preface
Thank you for purchasing the Itona E Series Thin Client. This guide contains information to setup and
use the hardware of Itona E Series.
The guide consists of the following chapters:
•Introduction: provides an overview of the product.
•Installation: contains the procedure to setup the hardware.
•Specifications: provides hardware, mechanical, electrical, interface and operating environment
specifications.
•Connectors and Cables: provides detailed specifications for connectors and cables used with the
product.
•Troubleshooting: provides solutions to problems that you may encounter while using the product.

VXL Instruments Ltd. Itona E series Hardware User’s Guide
Table of Contents 5
Table of Contents
Introduction........................................................................................................................................6
Overview........................................................................................................................................................6
Features ........................................................................................................................................................7
Optional Features ......................................................................................................................... 7
Step One: Unpack.........................................................................................................................................8
Step Two: Prepare.........................................................................................................................................8
Step Three: Connect accessories and power ...............................................................................................9
Caution:.......................................................................................................................................................10
Step Four: Connect to the Server................................................................................................................11
LAN connection through TCP/IP...............................................................................................................11
Specifications...................................................................................................................................12
Hardware.....................................................................................................................................................12
Mechanical ..................................................................................................................................................12
Environmental Operating.............................................................................................................................12
Electrical Power...........................................................................................................................................12
Regulatory Certifications .....................................................................................................................12
Connectors..................................................................................................................................................13
10/100/1000 LAN Port...............................................................................................................................13
Video Port..................................................................................................................................................13
Audio / Microphone Port............................................................................................................................13
USB Port....................................................................................................................................................13
Cables .........................................................................................................................................................14
10/100/1000 LAN Cable............................................................................................................................14
Troubleshooting...............................................................................................................................15

VXL Instruments Ltd. Itona E series Hardware User’s Guide
Introduction 6
Introduction
Overview
Thin Clients are essentially terminal devices that connect to multi-user application servers operating
under Citrix MetaFrame and Windows 2000/ 2003 operating systems.
This guide covers installation and hardware details of Itona E Series.
Itona E Series
Front View
Itona E Series deliver smart and robust solutions for Thin Client computing. They are aesthetically and
ergonomically designed compact desktop, providing simultaneous full screen connectivity to Windows
and UNIX application servers – a powerful business alternative to users using Win32 applications while
continuing access to legacy UNIX applications.
They communicate with application servers via the ICA protocol developed by Citrix Systems Inc.,
Remote Desktop Protocol from Microsoft and a host of other popular connectivity protocols. Please refer
to the Software User’s Guide for information about connection protocols supported by your model.
Power button
2 USB Port
LED HDD
LED LAN
MIC IN
Audio Line out
Smart Card (Optional)
Speaker

VXL Instruments Ltd. Itona E series Hardware User’s Guide
Introduction 7
Features
The product is equipped with a 10/100/1000 Ethernet port that gives an instant connection to a multi-
user Windows NT application server. Also provided video display port. USB compatible keyboard/Mouse
ports are available for quick setup and use.
Optional Features
•Wireless LAN
•Smart Card
•PCI Card
Note: The optional features cannot be upgraded in the field. Please contact the reseller or dealer from
whom you purchased the product for information about optional features.

VXL Instruments Ltd. Itona E series Hardware User’s Guide
Installation 8
Installation
This chapter describes hardware installation of the product.
Step One: Unpack
Unpack the unit taking care not to drop the product whilst removing from the packaging.
The carton in which the product was shipped to you contains the following:
•Itona E Series Thin Client
•Power Adapter AC-DC 12V / 4A
•Pedestal
•Power Cord (Optional)
•Mouse (Optional )
•Hardware Installation Guide
When you open the carton, if you find any discrepancy between the contents of the carton and the
above list, contact the dealer or reseller from whom you have purchased the product, immediately.
NOTE:PLEASE RETAIN THE ORIGINAL CARTON AND PACKING MATERIAL.THEY WOULD BE REQUIRED TO
AVOID DAMAGE DURING TRANSIT (IF REQUIRED IN FUTURE).
Step Two: Prepare
1. The site where you want to install the product must have the following
•100~240V AC, 0.65A, 50/60 Hz, 3-pin power Inlet for Power Adapter.
NOTE:ENSURE THAT THE POWER INLET PLUG IS PROPERLY REGULATED AND EARTHED.AFLOATING
GROUND /CHASSIS COULD CAUSE AN ELECTRIC SHOCK.
•Fix the pedestals at the bottom of the Itona E.
•Well ventilated, clean, dry and dust free atmosphere
•Specified environmental conditions (refer to the section on specifications )
•Table or desk of suitable size.
2. Place the product on the table in a location that provides quick and easy access to the power Inlet
plug to shutdown the power in emergencies.
3. Ensure a minimum space of 2 inches (5 cm) on all sides of the unit for efficient convection cooling.
9
9

VXL Instruments Ltd. Itona E Hardware User’s Guide
Installation 9
Step Three: Connect accessories and power
NOTE:BEFORE CONNECTING ANY CABLES,ENSURE POWER CABLE IS UNPLUGED FROM THE UNIT. PLEASE
USE 6A (MIN) /250V AC0.75 sq mm, H05VV-F CERTIFIED POWER CORD.
Pictures below show the various connectors available on the rear panel of the client.
Itona E Series
Rear view
9
USB Port
PS2 Port
Ethernet Port
DVI-I Port
VGA Port
DC Power IN 12V / 4A
Kensington Lock
COM Port
Pedestal
PCIe Card (Optional)

VXL Instruments Ltd. Itona E Hardware User’s Guide
Installation 10
The table below identifies the devices to be used with each connector of the client.
Instructions to connect various accessories
Connector Symbol
9Connect the video cable from your display unit to the video port
9Connect the DVI cable from your display unit to the DVI-I port
9Connect serial devices to the COM ports
1
9Connect USB devices to the USB ports
9Connect external powered speakers to the audio output(LINE
OUT) port
9Connect microphone to the Microphone input port
9Connect LAN cable to the RJ45 Ethernet port
9Connect DC 12V / 4 A Power Adapter to DC Jack 12V / 4A
Caution:
•Ensure that Video port adequately fastened with the screws provided with the cables
•Ensure the Power Rating Spec before Connecting Power Cable.

VXL Instruments Ltd. Itona E Hardware User’s Guide
Installation 11
Step Four: Connect to the Server
The Thin Client can be physically connected to the server/network:
•LAN connection through TCP/IP
LAN connection through TCP/IP
Connect one end of a 10/100/1000 cable to the LAN port of the client. Connect the other end to a LAN
hub as shown in the figure below.
LAN Connection through TCP/IP
Press the power button to power up the Itona E. The front panel LED lights up and the client boots up
with a BEEP sound and takes you to the Connection Manager screen. Refer to the Software User’s
Guide for configuring the client.
ICA Server
Ethernet
HUB
10/100Base-T
Host 2 Workstation Host 1
Winlinx
Thin Client

VXL Instruments Ltd. Itona E Hardware User’s Guide
Specification
12
Specifications
Hardware
•Processor: VIA Eden ULV 1.6GHz
•VGA Memory: Shared Video Memory 32MB min
•Flash : IDE 44Pin / 90D
•RAM: DDR2 SO DIMM 512MB to 2GB
•Networking 10/100/1000 Mbps
•PCI PCIex1
•Power supply External Adapter 12V /4A
•Display Support 1920x1200 60Hz 16/32 Bits
Mechanical
Itona E Series
•Height: 230 mm.
•Width: 57 mm.
•Depth: 210 mm.
•Weight: 1.7 Kg (max)
Environmental Operating
•Temperature : + 0oC to +35oC
•Storage temperature: - 20o C to +60oC
•Humidity: 20% to 80% RH Max non-condensing
Electrical Power
•4A/12V External Adapter,48 Watts
Regulatory Certifications
RoHS

VXL Instruments Ltd. Itona E Hardware User’s Guide
Cables and Connectors
13
Connectors and Cables
Connectors
The following tables provide pin details for various connectors on the rear panel of the client.
10/100/1000 LAN Port
RJ-45 modular 8-pin jack. 10/100/1000 Mbps
Pin Signal
1 TxD+
2 TxD-
3 RxD+
6 RxD-
Video Port
15-pin D-type female connector
Pin Signal Pin Signal Pin Signal
1 Red 6 Red return GND 11 No Connection
2 Green 7 Green return GND 12 No Connection
3 Blue 8 Blue return GND 13 Horizontal Sync
4 No Connection 9 No Connection 14 Vertical Sync
5 GND 10 No Connection 15 No Connection
Audio / Microphone Port
Standard audio jacks.
USB Port
4-pin series-A receptacle. 4~ 5 ports depending on the model. Both USB1.1 and USB2.0 models are
available.
Pin Signal
1 VCC
2 D-
3 D+
4 GND
1 8
5 1
10 6
15 11

VXL Instruments Ltd. Itona E Hardware User’s Guide
Cables and Connectors
14
Cables
10/100/1000 LAN Cable
Cross Connection - (Without Hub)
Straight Connection - (With Hub)
TXD+ 1 3 RXD+
TXD- 2
2 TXD-
RXD+ 3 1 TXD+
RXD- 6
6 RXD-
RJ45
Pin RJ45 Pin
TXD+ 1 1 TXD+
TXD- 2
6 RXD-
RXD+ 3 3 RXD+
RXD- 6
2 TXD-
RJ45
Pin RJ45 Pin

VXL Instruments Ltd. Itona E Hardware User’s Guide
Troubleshooting 15
Troubleshooting
This chapter contains solutions for problems you may encounter while using the product.
Problem Solution
•The Power-LED on front
panel does not glow when
the client is switched on.
9Ensure that the power cord is plugged into an AC outlet.
9Check the fuse in the power-plug, if available.
9
•There is no display, though
the power-indicating LED
glows.
•Make sure the monitor is plugged in to the terminal
•Make sure the VGA connector is plugged in to the terminal
•The mouse (or keyboard)
does not work when the
client is switched on.
9Ensure that the mouse (or keyboard) is plugged into the
correct USB port on the rear panel