Vxl TC15yy Installation manual

Itona TC15yy
Hardware User Guide

Copyright © 2004-2012 VXL Instruments Limited. All Rights Reserved.
Information in this document is subject to change without notice and does not represent a
commitment on the part of the manufacturer. No part of this guide may be reproduced or transmitted
in any form or means, electronic or mechanical, including photocopying and recording, for any
purpose, without the express written permission of the manufacturer.
Every effort has been made to make this guide as complete and as accurate as possible, but no
warranty or fitness is implied. The authors and the publisher shall have neither responsibility nor
liability to any person or entity with respect to loss or damages arising from the use of information
contained in this guide. This disclaimer does not apply in countries where such provisions are
inconsistent with local law.
All Trademarks are acknowledged.
Last Updated: September, 2012
Version: TC15yy/UG-37-12
VXL Instruments Ltd.,
House of Excellence,
No. 17, Electronics City,
Hosur Road,
Bangalore–560 100, INDIA.
www.vxl.net

i
Federal Communication Commission
(FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment Off and On, the user is encouraged to try to correct
the interference by one or more of the following measures:
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio / television technician for help.
Each Thin Client is equipped with a FCC compliance label that shows only the FCC
identification number. The full information of the associated label is as follows:
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.

ii
Energy Star Compliant Product
ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and
the U.S. Department of Energy helping us all save money and protect the
environment through energy efficient products practices.
Products with the ENERGY STAR logo comply with the ENERGY STAR standard,
and the power management feature is enabled by default. The monitor and computer
are automatically set to sleep after 15 and 30 minutes of user inactivity. To wake your
computer, click the mouse or press any key on the keyboard.
Please visit http://www.energy.gov/powermanagement for detail information on power
management and its benefits to the environment. In addition, please visit
http://www.energystar.gov for detail information on the ENERGY STAR joint program

iii
Regulatory Certifications

iv
Table of Contents
Federal Communication Commission (FCC) Statement i
Energy Star Compliant Product ii
Regulatory Certifications iii
1Introduction 1
Features 1
Optional Features 2
About the User Guide 2
Abbreviations and Acronyms 2
Chapters in the Manual 3
2Installation 4
Unpacking the Unit 4
Preparing to Connect 4
Connecting the Accessories and Power Supply 5
Connecting to the Server 6
3Specifications 8
Hardware 8
Mechanical 8
Environmental Operating 8
Electrical Power 8
4Troubleshooting 9
Appendix 10

1 Introduction
1 Introduction
Thin Clients are terminal devices that connect to multi-user application servers operating
under Citrix MetaFrame and Windows Server 2000/2003 operating systems.
This guide covers installation procedure and hardware details of Itona TC 15yy series..
Figure 1: ItonaTC15yy
Itona TC 15yy series delivers smart and robust solutions for Thin Client computing. They are
aesthetically and ergonomically designed compact desktop, providing simultaneous full
screen connectivity to Windows and UNIX application servers–a powerful business
alternative to users using Win32 applications while continuing access to legacy UNIX
applications.
They communicate with application servers via the ICA protocol developed by Citrix Systems
Inc., Remote Desktop Protocol from Microsoft and a host of other popular connectivity
protocols. Please refer to the Software User’s Guide for information about connection
protocols supported by this model.
Features
The product is equipped with a 10/100/1000 Ethernet port that gives an instant connection to
a multi-user Windows NT application server. Also provided video display port. USB
compatible keyboard/Mouse ports are available for quick setup and use.
1. Power Button.
2. USB Ports.
1
2

Introduction 2
Optional Features
Wireless LAN is an optional features available for Itona TC15yy series.
Note: The optional features cannot be upgraded after the purchase of the product.
Please contact the reseller or dealer from whom you purchased the product for
information about optional features.
About the User Guide
This User Guide provides step-by-step instructions to install TC15yy series hardware. The
specifications and troubleshooting steps are also included in this User Guide.
Abbreviations and Acronyms
Abbreviation
Expansion
AC
Alternating Current
DC
Direct Current
LAN
Local Area Network
LED
Light Emitting Diode
TCP/IP
Transmission Control Protocol/Internet Protocol
USB
Universal Serial Bus
VESA
Video Electronics Standards Association
VGA
Video Graphics Array
Table 1: Abbreviations and Acronyms

3 Introduction
Chapters in the Manual
Chapter No
Chapter Name
Description
1
Introduction
Contains an overview of the product,
information about this guide and
abbreviations used in this guide.
2
Installation
Contains the procedure to set up the
hardware.
3
Specifications
Contains hardware, mechanical, electrical,
interface and operating environment
specifications.
4
Troubleshooting
Contains solutions to problems that you
may encounter while using the product.
—
Appendix
Contains detailed specifications for
connectors and cables used with the
product.
Table 2: List of Chapters
Warning
Do not open enclosure, hazardous voltages present inside equipment.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
There is no user serviceable part inside. Do not open enclosure, hazardous voltages
present in the equipment’s components. Do not disassemble the equipment as this
can nullify your warranty.
This equipment must be earthed to prevent accidental electric shocks, connect a
three pin connector to ensure adequate earthing.
As a precaution, the AC socket outlet should be near the equipment and should be
easily accessible.
Sound Power Level is less than 60dB (A), when measured according to ISO 7779.
Caution
Ensure that all expansion slots (on the back or side of the client) are covered with
metal retaining brackets, and tightly attached to the computer cabinet.
Only equipment certified to comply with Class B (computer input/output devices,
terminals, printers etc.) should be connected to this equipment, and must have
shielded interface cables.
This equipment should not be used in electro-medical applications.
Do not operate this equipment in corrosive or explosive atmosphere.
Operate this equipment within specified temperature limits.

Installation 4
2 Installation
You have to install the client before you can use it. Installation involves setting up the
hardware and connecting the peripherals required for normal use.
To install the Itona TC15yy series hardware, perform the following steps:
1. Unpack the unit.
2. Prepare to connect.
3. Connect the accessories and power.
4. Connect to the server
Each step is explained in detail in this chapter.
Unpacking the Unit
Unpack the unit from its carton box, handle safely to ensue you do not damage any
components during unpacking.
The carton in which the product was shipped to you contains the following:
Itona TC15yy Series Thin Client
Power Adapter AC-DC 16V/2.5A
Power cord
Pedestal
DVI-I to VGA and DVI cable (optional)
Wall / VESA mounting bracket (optional)
Mouse (optional)
Hardware Installation Guide
Note: Please retain the original carton and packing material for future use.
Preparing to Connect
1. Ensure that the following are available at the site where you want to install the product.
100~240V AC, 0.65A, 50/60 Hz, 3-pin power inlet for power adapter.
Note: Ensure that the power inlet plug is regulated and earthed. A floating
ground/chassis could cause an electric shock.
Well ventilated, clean, dry and dust free atmosphere.
Specified environmental conditions. For more information see, Environmental Operating
Specifications on page 8.
Table or desk of suitable size.
2. Fix the pedestals at the bottom of the thin client.

5 Installation
3. Place the product on the table in a location that provides quick and easy access to the power
Inlet plug to shutdown the power in emergencies.
4. Ensure a minimum space of 2 inches (5 cm) on all sides of the unit for efficient convection
cooling.
Connecting the Accessories and Power Supply
The various connectors available on the rear panel of the client are shown in Figure 2.
Figure 2: Itona TC15yy Series Rear View
1. Wireless LAN
2. DVI-I Port
3. Ethernet Port
4. Mic
5. 3 USB port
6. DC input 16V /2.5A
7. Pedestal
8. Line Out

Installation 6
Connectors
Connector Symbol
DVI-I port
USB port
Audio output (LINE OUT)
port
Microphone input port
RJ45 Ethernet port
Table 3: Connector Symbols
Note: Before connecting any cables, ensure that the power cable is unplugged from the
unit.
To connect various accessories and power supply:
1. Connect the DVI cable from your display unit to the DVI-I port.
2. Connect the USB devices to the USB ports.
3. Connect the external powered speakers to the audio output (LINE OUT) port.
4. Connect the microphone to the microphone input port.
5. Connect the mouse and keyboard to the USB slots.
6. Connect the LAN cable to the RJ45 Ethernet port.
7. Connect the DC power adapter to the DC power in.
Caution:
Ensure the Power Rating Spec before Connecting Power Cable.
Ensure that Video port adequately fastened with the screws provided with the cables.
Connecting to the Server
The Thin Client can be physically connected to the server/network by connecting to LAN
through TCP/IP.
To connect client to LAN through TCP/IP:
1. Connect one end of a 10/100/1000 cable to the Ethernet LAN port of the client.
2. Connect the other end to a LAN hub as shown in Figure 3.

7 Installation
Figure 3: LAN Connection through TCP/IP
3. Press the power button to switch on the ItonaTC15yy series thin client. The front panel
LED lights up and the client starts with a beep sound. The Connection Manager screen
appears.
Note: To configure the client, refer to the Software User’s Guide.

Specifications 8
3 Specifications
Hardware
Processor
VIA C7 / TC1000
VGA Memory
Shared Video Memory 32MB max
Flash
IDE 44Pin / 90D
RAM
DDR2 SO DIMM
Networking
10/100/1000Mbps
Power Supply
External Adapter
Display Support
1920x1200 60Hz 16/32 Bits
Mechanical
Height
190 mm
Width
36.5 mm
Depth
142 mm
Weight
0.7 Kg
(max)
Environmental Operating
Operating temperature
+ 5oC to +35oC
Storage temperature
- 20o C to +60oC
Humidity
20% to 80% RH Max non-
condensing
Electrical Power
2.5A/16V external adapter, 40 Watts

9 Troubleshooting
4 Troubleshooting
This chapter contains solutions for problems you may encounter while using the product.
Problem
Solution
The power-LED on front panel
does not glow when the client
is switched on.
Ensure that the power cord is plugged into an AC outlet.
Check the fuse in the power-plug, if available.
There is no display on the
monitor, though the power-
indicating LED glows.
Ensure the monitor is plugged in to the terminal.
Ensure that the VGA connector is plugged in to the terminal.
The mouse (or keyboard) does
not work when the client is
switched on.
Ensure that the mouse (or keyboard) is plugged into the
correct USB port on the rear panel.

Appendix 10
Appendix
Connectors
The following section provides pin details for various connectors on the rear panel of the
client.
10/100/1000 Ethernet LAN Port
RJ-45 modular 8-pin jack. 10/100/1000 Mbps.
DVI-I Port
Pin C1 to C5 carry the analogue signal.24+ 5 pin DVI Connector.
Pin
Signal
Pin
Signal
Pin
Signal
1
TMDS Data 2-
11
TMDS Data 1/3
Shield
21
TMDS Data 5+
2
TMDS Data 2+
12
TMDS Data 3-
22
TMDS Clock
Shield
3
TMDS Data 2/4
Shield
13
TMDS Data 3+
23
TMDS Clock +
4
TMDS Data 4-
14
+5 V Power
24
TMDS Clock -
5
TMDS Data 4+
15
Ground(for+5V)
C1
Analog Red
Pin
Signal
1
TxD+
2
TxD-
3
RxD+
6
RxD-

11 Appendix
6
DDC Clock
16
Hot Plug Detect
C2
Analog Green
7
DDC Data
17
TMDS Data 0-
C3
Analog Blue
8
Analog Vertical
Sync
18
TMDS Data 0+
C4
Analog Horizontal
Sync
9
TMDS Data 1-
19
TMDS Data 0/5
Shield
C5
Analog Ground
(analog R, G & B
return)
10
TMDS Data 1+
20
TMDS Data 5-
Audio / Microphone Port
Standard audio jacks.
USB Port
4-pin series-A receptacle. 4~ 5 ports depending on the model. Both USB1.1 and USB2.0
models are available
Pin
Signal
1
VCC
2
D-
3
D+
4
GND