W3 Gear PORTABLE POWER 6200 User manual

Owner’s Manual
Revision 2.11
Last Updated: 6-JUN-2012
Warning and Notice
- KEEP THE PORTABLE POWER 6200 AWAY FROM FLAME
- DO NOT INVERT BATTERY POLARITY
- DO NOT ALLOW THIS PRODUCT TO COME WITH CONTACT WITH WATER OR OTHER LIQUIDS
- DO NOT EXPOSE THIS PRODUCT IN AN ENVIRONMENT OVER 60°C OR DIRECT SUN SHINE IN THE CAR
- KEEP THIS PRODUCT AWAY FROM CHILDREN
- PLEASE DO NOT TOUCH THE INTERNAL CIRCUIT
© 2012 W3GEAR. All rights reserved.
Designated trademarks and brands are the property of their respective owners.

Standard Features
Battery Type
2 x 18650 Lithium Ion Battery
Capacity
3.7V 6200mAh
Rated Output
DC 5V ± 5%, Max 1000mA
Rated Input
DC 5V ± 5%, Max 1000mA
Standby Current
< 5uA
Recharge Time
6 - 8 hours
Indicator LEDs
- Blue LED: Above 60% power
- Green LED: 30% ~ 60% power
- Red LED: Below 30% power
Size
43mm x 107mm x 25mm
Weight
150g (Unit w/Batt) / 260g (Package)
Operating temperature
-10 ~ 40 degrees Celsius
Storage temperature
-20 ~ 60 degrees Celsius
Package Content
1x Portable Power 6200
1x iPhone/iPad charging cable
1x 10-in-1 charging cable
2x 3100mAh NCR18650A Lithium Ion Battery
1 x Owner's Manual

Before Using the Portable Power 6200
The Portable Power 6200 uses 2 x 18650 lithium ion batteries (the same sort of battery inside most laptop).
We charge them up before we send them out –however, due to time in transit, you’ll need to top it up before
using it.
To install the batteries for Portable Power 6200:
Remove the battery cover by sliding
the cover off the back of the Portable
Power 6200
Insert the 18650 battery, observing the proper
polarity into the battery compartment
Replace the battery cover by sliding it
back onto the Portable Power 6200
and fastening the latch
Using a sharp object eg. Needle or Tooth pick,
push the Circuit Breaker Re-Activation Switch
to start using the battery for the first time
To charge the batteries for Portable Power 6200:
1. Locate the mini-USB port on the top of the Portable Power 6200
2. Using the supplied charging cable, attached the Portable Power 6200 to a USB port on your computer, or
any 1A USB wall charger
3. While charging, the red LED will stay on and it will turn to green when charging is completed.
4. The Portable Power 6200 requires approximately 6 - 8 hours for a full charge.

Operating the Portable Power 6200
To turn the Portable Power 6200 ON:
Connect the Portable Power 6200 to your mobile phone/USB device using the suitable connector supplied.
Press and hold the Power Button for approximately three seconds.
The red LED will stay on, this indicates that the Portable Power 6200 now powering your mobile
phone/USB device.
To turn the Portable Power 6200 OFF:
Unplug your mobile phone/USB device from the Portable Power 6200.
After unplugging from your mobile phone/USB device, the Portable Power 6200 will automatically shut
down after 15 seconds of inactivity.
DO NOTE REMOVE THE BATTERY COVERY WHILE CHARGING.
To check battery level on Portable Power 6200:
While not connected to any device, press and hold on the power button, and you should see one or more
colors of LED indicator light up.
Low Power & Automatic Shutdown:
When the Portable Power 6200 battery starts to run low, it will automatically shut itself down. If this happens,
recharge the battery fully before turning the Portable Power 6200 on again.
The intelligent protection circuit in the Portable Power 6200 may automatically shutdown in the event of a
short circuit or over heat / discharge for safety purpose. You can perform a reset on the Circuit Breaker Re-
Activation Switch using a sharp tipped object eg. Needle or tooth pick.