Wacker Neuson GV 7000A User manual

www.wackergroup.com
Generator
GV 7000A
GV 7003A
OPERATOR’S MANUAL
0157387en 004
1106
0157387EN

DANGER
CARBON MONOXIDE
Using a generator indoors CAN KILL YOU IN MINUTES.
Generator exhaust contains carbon monoxide (CO). This is a poison you cannot see or
smell. If you can smell the generator exhaust, you are breathing CO. But even if you cannot
smell the exhaust, you could be breathing CO.
• NEVER use a generator inside homes, garages, crawlspaces, or other partly enclosed
areas. Deadly levels of carbon monoxide can build up in these areas. Using a fan or
opening windows and doors does NOT supply enough fresh air.
• ONLY use a generator outside and far away from windows, doors, and vents. These
openings can pull in generator exhaust.
Even when you use a generator correctly, CO may leak into the home. ALWAYS use a
battery-powered or battery-backup CO alarm in the home.
If you start to feel sick, dizzy, or weak after the generator has been running, move to fresh
air RIGHT AWAY. See a doctor. You could have carbon monoxide poison.

GV 7000A/7003A Table of Contents
wc_bo0157387004enTOC.fm 1
1. Foreword 3
2. Safety Information 4
2.1 Operating Safety .................................................................................. 5
2.2 Operator Safety while using Internal Combustion Engines .................. 6
2.3 Service Safety ...................................................................................... 7
2.4 Label Locations .................................................................................... 8
2.5 Safety and Operating Labels ................................................................ 9
3. Technical Data 11
3.1 Generator ........................................................................................... 11
3.2 Engine ................................................................................................ 13
3.3 Sound Specifications .......................................................................... 13
4. Operation 14
4.1 Determining Power Requirements ..................................................... 14
4.2 Outdoor Installation ............................................................................ 16
4.3 Indoor Installation ............................................................................... 16
4.4 Generator Derating ............................................................................. 17
4.5 Use of Extension Cords ...................................................................... 18
4.6 Grounding the Generator ................................................................... 20
4.7 Operating Heavy Loads ...................................................................... 20
4.8 Control Panel ...................................................................................... 21
4.9 Before Starting ................................................................................... 23
4.10 To Start ............................................................................................... 24
4.11 To Stop ............................................................................................... 24

Table of Contents GV 7000A/7003A
wc_bo0157387004enTOC.fm 2
5. Maintenance 25
5.1 Engine Maintenance ............................................................................25
5.2 Periodic Maintenance Schedule ..........................................................25
5.3 Engine Oil ............................................................................................26
5.4 Air Cleaner ..........................................................................................27
5.5 Spark Plug ...........................................................................................28
5.6 Engine Speed ......................................................................................29
5.7 Storage ................................................................................................30
5.8 Transport .............................................................................................30
5.9 Troubleshooting ...................................................................................31
5.10 Electrical Schematic—GV 7000A ........................................................32
5.11 Electrical Schematic—GV 7003A ........................................................33

Foreword
wc_si000108gb.fm 3
1. Foreword
This manual provides information and procedures to safely operate
and maintain this Wacker model. For your own safety and protection
from injury, carefully read, understand and observe the safety
instructions described in this manual.
Keep this manual or a copy of it with the machine. If you lose this
manual or need an additional copy, please contact Wacker
Corporation. This machine is built with user safety in mind; however,
it can present hazards if improperly operated and serviced. Follow
operating instructions carefully! If you have questions about operating
or servicing this equipment, please contact Wacker Corporation.
The information contained in this manual was based on machines in
production at the time of publication. Wacker Corporation reserves the
right to change any portion of this information without notice.
All rights, especially copying and distribution rights, are reserved.
Copyright 2006 by Wacker Corporation.
No part of this publication may be reproduced in any form or by any
means, electronic or mechanical, including photocopying, without
express written permission from Wacker Corporation.
Any type of reproduction or distribution not authorized by Wacker
Corporation represents an infringement of valid copyrights and will be
prosecuted. We expressly reserve the right to make technical
modifications, even without due notice, which aim at improving our
machines or their safety standards.

Safety Information GV 7000A / 7003A
wc_si000108gb.fm 4
2. Safety Information
This manual contains DANGER, WARNING, CAUTION, and NOTE
callouts which must be followed to reduce the possibility of personal
injury, damage to the equipment, or improper service.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
CAUTION: Used without the safety alert symbol, CAUTION indicates
a potentially hazardous situation which, if not avoided, may result in
property damage.
Note: Contains additional information important to a procedure.
DANGER
WARNING
CAUTION

GV 7000A / 7003A Safety Information
wc_si000108gb.fm 5
2.1 Operating Safety
BACKFEED FROM THE GENERATOR INTO THE PUBLIC POWER
DISTRIBUTION SYSTEM CAN CAUSE SERIOUS INJURY OR
DEATH TO UTILITY WORKERS!
Improper connection of generator to a building's electrical system can
allow electrical current from the generator to backfeed into utility lines.
This may result in electrocution of utility workers, fire, or explosion.
Connections to a building's electrical system must be made by a
qualified electrician and comply with all applicable laws and electrical
codes.
If connected to a building's electrical system the generator must meet
the power, voltage, and frequency requirements of the equipment in
the building. Differences in power, voltage, and frequency
requirements may exist and improper connection may lead to
equipment damage, fire, and personal injury or death.
Familiarity and proper training are required for the safe operation of
equipment. Equipment operated improperly or by untrained personnel
can be dangerous. Read the operating instructions contained in both
this manual and the engine manual and familiarize yourself with the
location and proper use of all controls. Inexperienced operators should
receive instruction from someone familiar with the equipment before
being allowed to operate the machine.
2.1.1 NEVER operate the generator when open containers of fuel, paint, or
other flammable liquids are near.
2.1.2 NEVER operate the generator, or tools attached to the generator, with
wet hands.
2.1.3 NEVER use worn electrical cords. Severe electrical shock and
equipment damage may result.
2.1.4 NEVER run the electrical cords under the generator, or over vibrating
or hot parts.
2.1.5 NEVER enclose or cover the generator when it is in use or when it is
hot.
2.1.6 NEVER overload the generator. The total amperage of the tools and
equipment attached to the generator must not exceed the load rating
of the generator.
2.1.7 NEVER operate the machine in snow, rain, or standing water.
2.1.8 NEVER allow untrained personnel to operate or service the generator.
The generator set should be set up by a trained electrician.
2.1.9 ALWAYS store the equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the reach of
children.
DANGER
WARNING

Safety Information GV 7000A / 7003A
wc_si000108gb.fm 6
2.1.10 ALWAYS be sure the machine is on a firm, level surface and will not
tip, roll, slide, or fall while operating.
2.1.11 ALWAYS transport the generator in an upright position.
2.1.12 ALWAYS keep the machine at least one meter (three feet) away from
structures, buildings, and other equipment during use.
2.1.13 ALWAYS keep the area immediately surrounding and underneath the
machine clean, neat, and free of debris and combustible materials.
Make sure that the area overhead is clear of debris that could fall onto
or into the machine or exhaust compartment.
2.1.14 ALWAYS remove all tools, cords, and other loose items from the
generator before starting it.
2.1.15 DO NOT ground this generator.
2.2 Operator Safety while using Internal Combustion Engines
Internal combustion engines present special hazards during operation
and fueling. Read and follow the warning instructions in the engine
owner’s manual and the safety guidelines below. Failure to follow the
warnings and safety guidelines could result in severe injury or death.
2.2.1 DO NOT run the machine indoors or in an enclosed area such as a
deep trench unless adequate ventilation, through such items as
exhaust fans or hoses, is provided. Exhaust gas from the engine
contains poisonous carbon monoxide gas; exposure to carbon
monoxide can cause loss of consciousness and may lead to death.
2.2.2 DO NOT smoke while operating the machine.
2.2.3 DO NOT smoke when refueling the engine.
2.2.4 DO NOT refuel a hot or running engine.
2.2.5 DO NOT refuel the engine near an open flame.
2.2.6 DO NOT spill fuel when refueling the engine.
2.2.7 DO NOT run the engine near open flames.
2.2.8 DO NOT start the engine if fuel has spilled or a fuel odor is present.
Move the generator away from the spill and wipe the generator dry
before starting.
2.2.9 ALWAYS refill the fuel tank in a well-ventilated area.
2.2.10 ALWAYS replace the fuel tank cap after refueling.
2.2.11 ALWAYS check the fuel lines and the fuel tank for leaks and cracks
before starting the engine. Do not run the machine if fuel leaks are
present or the fuel lines are loose.
DANGER

GV 7000A / 7003A Safety Information
wc_si000108gb.fm 7
2.3 Service Safety
Poorly maintained equipment can become a safety hazard! In order
for the equipment to operate safely and properly over a long period of
time, periodic maintenance and occasional repairs are necessary. If
the generator is experiencing problems or is being serviced, attach a
“DO NOT START” sign to the control panel to notify other people of its
condition.
2.3.1 DO NOT use gasoline or other types of fuels or flammable solvents to
clean parts, especially in enclosed areas. Fumes from fuels and
solvents can become explosive.
2.3.2 DO NOT attempt to clean or service the machine while it is running.
2.3.3 DO NOT modify the equipment without the express written approval of
the manufacturer.
2.3.4 DO NOT allow water to accumulate around the base of the machine.
If water is present, move the machine and allow the machine to dry
before servicing.
2.3.5 DO NOT service the machine if your clothing or skin is wet.
2.3.6 DO NOT allow untrained personnel to service this equipment. Only
trained electrical technicians should be allowed to service the electrical
components of this equipment.
2.3.7 ALWAYS keep the machine clean and labels legible. Replace all
missing and hard-to-read labels. Labels provide important operating
instructions and warn of dangers and hazards.
2.3.8 ALWAYS replace the safety devices and guards after repairs and
maintenance.
2.3.9 ALWAYS let the engine cool before transporting or servicing it.
2.3.10 ALWAYS keep hands, feet, and loose clothing away from the moving
parts on the generator and engine.
2.3.11 ALWAYS turn the engine off before servicing the machine. If the
engine has electric start, disconnect the negative terminal on the
battery before servicing the machine.
2.3.12 ALWAYS keep the fuel lines in good condition and properly connected.
Leaking fuel and fumes are extremely explosive.
WARNING

Safety Information GV 7000A / 7003A
wc_si000108gb.fm 8
2.4 Label Locations
wc_gr001298
PETROL
GASOLINA
ISSINCI
BENZIN
CALDO !
HEISS !
HOT !
CHAUD !
DANGER
GEFAHR
PELIGRO
DANGER
DANGER
GEFAHR
PELIGRO
DANGER

GV 7000A / 7003A Safety Information
wc_si000108gb.fm 9
2.5 Safety and Operating Labels
Wacker machines use international pictorial labels where needed.
These labels are described below:
Label Meaning
WARNING!
Hot surface!
Close the choke.
Gasoline
Potential Earth.
WARNING!
Electric shock will cause serious injury or
death.
WARNING!
Electric shock hazard. Read operator’s manual
for instructions.
CALDO !
HEISS !
HOT !
CHAUD !
PETROL
GASOLINA
ISSINCI
BENZIN
DANGER
GEFAHR
PELIGRO
DANGER

Safety Information GV 7000A / 7003A
wc_si000108gb.fm 10
DANGER!
Asphyxiation hazard. Read the operator’s
manual for instructions.
DANGER!
No sparks, flames or burning objects near
machine.
Fuel valve
Guaranteed sound power level in dB(A)
A nameplate listing the model number, item
number, revision number, and serial number is
attached to each unit. Please record the
information found on this plate so it will be
available should the nameplate become lost or
damaged. When ordering parts or requesting
service information, you will always be asked
to specify the model number, item number,
revision number, and serial number of the unit.
Label Meaning
DANGER
GEFAHR
PELIGRO
DANGER
hz
151710
I
n
s
.
c
l
ass
COS
Ø
kW
k
g
Ø
l
bs
A
V
N
/M
class
R
e
v
.
M
odel
I
t
em No
.
Se
ri
a
l N
o.
GE
N
E
RAT
I
N
G
SE
T
ISO
8528
MA
DE
IN
I
TA
LY

GV 7000A/7003A Technical Data
wc_td000107gb.fm 11
3. Technical Data
3.1 Generator
Item No. 0009348 0009353 0009358 0009363
GV 7000A Generator
Maximum Output kVA 6.05
Continuous Output kVA 5.5
Type Single voltage, single phase.
Brushless, capacitor regulator system
AC Voltages Available Volts
phase
230
1ø
Frequency Hz 50
Power Factor 0.9
AC receptacles:
230V, 16Amp Schuko
230V, 16Amp French
230V, 16Amp Swiss
230V, 16Amp CEE
230V, 32Amp Schuko
230V, 32Amp French
230V, 32Amp Swiss
230V, 32Amp CEE
Quantity
1
-
-
-
1
-
-
-
-
1
-
-
-
1
-
-
-
-
1
-
-
-
1
-
-
-
-
1
-
-
-
1
Main Circuit Breaker Amp 20
Dimensions L x W x H mm (in.) 735 x 510 x 520 (29 x 20 x 20.5)
Weight (dry) Kg (lbs.) 72 (159)

Technical Data GV 7000A/7003A
wc_td000107gb.fm 12
Item No. 0009349 0009354 0009359 0009364
GV 7003A Generator
Maximum Output kVA 7.45
Continuous Output kVA 7.1
Type Dual voltage, multiple phase,
brush-type, compound regulator system
AC Voltages Available Volts
phase
230/1ø
400/3ø
Frequency Hz 50
Power Factor 0.8
AC receptacles:
230V, 16Amp Schuko
230V, 16Amp French
230V, 16Amp Swiss
230V, 16Amp CEE
400V, 16Amp CEE
400V, 16Amp Swiss
Quantity
1
-
-
-
1
-
-
1
-
-
1
-
-
-
1
-
-
1
-
-
-
1
1
-
Main Circuit Breaker Amp 10, 12, 10 2-Pole
Dimensions L x W x H mm (in.) 735 x 510 x 520 (29 x 20 x 20.5)
Weight (dry) Kg (lbs.) 81 (179)

GV 7000A/7003A Technical Data
wc_td000107gb.fm 13
3.2 Engine
* Continuous Operating Power
3.3 Sound Specifications
The required sound specification, Paragraph 1.7.4.f of 89/392/EEC
Machinery Directive, is:
• guaranteed sound power level (LWA) = 97 dB(A).
This sound value was determined according to ISO 3744 for the sound
power level (LWA).
GV 7000A GV 7003A
Engine
Engine Make Honda
Engine Model GX390K1-VPX4
Rated Power kW (Hp) 8.3 (11.1)
Spark Plug BPR6ES / W20EPR-U
Electrode Gap mm (in.) 0.7 - 0.8 (0.028 - 0.031)
Engine Speed - full load rpm 3000 ± 100
Engine Speed - no load rpm 3100 ± 100
Air Cleaner type Oil-wetted foam element
Engine Lubrication oil grade SAE 10W30 service class SJ
Engine Oil Capacity l (qts.) 1.1 (1.2)
Fuel type Regular unleaded gasoline
Fuel Tank Capacity l (gal.) 11 (3)
Fuel Consumption
3/4 COP*
l (qts.)/hr. 2.15 (2.27) 1.98 (2.09)
Running Time
3/4 COP*
hrs. 5.1 5.6

Operation GV 7000A/7003A
wc_tx000273gb.fm 14
4. Operation
4.1 Determining Power Requirements
Wacker generator Model GV 7000A is designed to operate single-
phase, 50 Hertz appliances running at 230 VAC. Model GV 7003A is
designed to operate single phase, 50 Hertz appliances running at
230VAC and/or three-phase, 50 Hertz appliances running at 400VAC.
Both single and three phase sides of the generator may be run at the
same time.
CAUTION: Do not exceed the power output of the generator. Damage
to tools or generator will occur. See Technical Data.
Check the nameplate or label provided on tools and appliances to
make sure their power requirements are met by the power output of the
generator. If the wattage is not given for a particular tool or appliance,
contact the tool manufacturer for wattage requirements.
Some appliances and tools require a surge of current when starting.
This means that the amount of power needed to initially start the
equipment is larger than the power required to keep it running. The
generator must be capable of supplying this "surge" current. Other
types of appliances require more power than is actually stated on their
nameplate.
The information in “Approximate Starting Power Requirements” is
offered only as a general guideline to help you determine power
requirements for different types of equipment. Check with your nearest
Wacker dealer, or contact the manufacturer or dealer of the tool or
appliance, if you have questions regarding power requirements.
CAUTION: DO NOT exceed the rated current limit of any receptacle.
CAUTION: If a tool or appliance does not reach full speed within a few
seconds after it is switched on, turn it off immediately to avoid damage.

GV 7000A/7003A Operation
wc_tx000273gb.fm 15
Approximate Starting Power Requirements
• Incandescent lights and appliances such as irons and hot plates,
which use a resistive-type heating element, require the same wattage
to start and run as is stated on their nameplates.
• Fluorescent and mercury lamps require 1.2–2 times their stated watt-
age to start.
• Electrical motors and many types of electrical tools often require a
large starting current. The amount of starting current depends on the
type of motor and its use.
• Most electrical tools require 1.2–3 times their stated wattage for start-
ing.
• Loads such as submersible pumps and air compressors require a
very large force to start. They need as much as 3–5 times the wattage
stated on the nameplate in order to start.
If the wattage is not given for a particular tool or appliance, it can be
calculated by multiplying its voltage and amperage requirements:
Single Phase: VOLTS x AMPS = WATTS
Three Phase: VOLTS x AMPS x 1.732 x 0.8 = WATTS

Operation GV 7000A/7003A
wc_tx000273gb.fm 16
4.2 Outdoor Installation
Place the generator in an area where it will not be exposed to rain,
snow, or direct sunlight. Make sure it is positioned on firm, level
ground, so it will not slide or shift. Position the engine exhaust away
from areas where people may be present.
If operating the generator inside a tunnel or deep trench, make sure
there is adequate ventilation. Precautions similar to those required
when operating indoors may be necessary.
The surrounding area must be free from water and moisture. All
components must be protected from excessive moisture.
4.3 Indoor Installation
If the generator must be installed indoors, adequate ventilation or
exhaust hoses must be provided. When venting exhaust fumes, make
sure the exhaust piping is large enough to prevent excessive back
pressure to the engine. Back pressure reduces engine efficiency and
may cause the engine to overheat.
Exhaust gas from the engine contains poisonous carbon monoxide
gas; exposure to carbon monoxide can cause loss of consciousness
and may lead to death. Never run the generator indoors or in an
enclosed area unless adequate ventilation, through such items as
exhaust hoses or fans, is provided.
When installed indoors, steps to prevent fire and explosion such as
providing a good, earthen ground, removing all flammable materials
near the generator, and using only electrical cables in good condition,
must be observed. See Operating Safety.
DANGER

GV 7000A/7003A Operation
wc_tx000273gb.fm 17
4.4 Generator Derating
All generators are subject to derating for altitude and temperature.
Internal combustion engines, unless modified, run less efficiently at
higher altitudes due to the reduction of air pressure. This translates
into a lack of power and thus reduction in generator output.
Temperature affects both engine and generator performance. As
temperature increases, an engine will run less efficiently and more
resistance will be found in electrical components. Therefore, as the
temperature increases, the output of the generator decreases. Altitude
also affects the cooling capacity of air—the higher the altitude the less
dense the air is and thus the lower its ability to transfer heat.
For every increase in altitude of 500 m (1650 ft.) above 1000 m (3300
ft.), the output of the generator will be reduced by 3%. For every
increase of 5° C (9° F) in ambient temperature above 40° C (104° F),
the output of the generator will be reduced by 3%. Use the tables
shown for altitude and temperature deration factors. It may be
necessary to consider both altitude and ambient temperature deration
factors to determine true generator output.
Ambient Temp.
°C (°F) Derate Factor
45 (113) 3 % 0.97
50 (122) 6 % 0.94
55 (131) 9 % 0.91
60 (140) 12 % 0.88
Altitude
m (ft.) Derate Factor
1500 (4900) 3 % 0.97
2000 (6600) 6 % 0.94
2500 (8200) 9 % 0.91
3000 (9900) 12 % 0.88
3500 (11500) 15 % 0.85
4000 (13100) 18 % 0.82

Operation GV 7000A/7003A
wc_tx000273gb.fm 18
4.5 Use of Extension Cords
When a long extension cord is used to connect an appliance or tool to
the generator, a voltage loss occurs—the longer the cord, the greater
the voltage loss. This results in less voltage being supplied to the
appliance or tool and increases the amount of current draw or reduces
performance. A cord with a larger cross section will reduce the voltage
loss.
CAUTION: Operating equipment at low voltage can cause it to
overheat.
Use only tough rubber-sheathed cable in accordance with IEC 245-4.
Damaged cords can cause electric shock. Electric shock can cause
serious injury or death. DO NOT use worn, bare, or frayed cords.
Replace damaged cords immediately.
Do not exceed the rating of the cord.
Contact the cord manufacturer if in doubt about cord use.
Choose the cord size from the Minimum Extension Cord Size Table or
calculate minimum cord size using the Minimum Extension Cord Size
Graph. The X axis of the graph represents A x m (Ampere x meter)
values. The Y axis represents wire size in mm2. Multiply the operating
current for the load in amps (A) by the desired extension cord length in
meters (m). Find the result along the X axis. Move up the graph until
you reach the appropriate sloped line for your application. Move to the
Y axis; this is the recommended minimum cord size.
Example:
For a 3-phase, 400V application, if the operating current for the load is
15 A, and the desired extension cord length is 100 m, then:
15 A x 100 m = 1500 A x m.
1500 A x m = 2.5 mm2.
WARNING