WAGO I/O-SYSTEM 750 User manual

Pos:2/Dokumentationallgemein/Einband/EinbandHandbuch- F ro nts ei t e 2015 - mit DocV ari abl e n (Sta nd ar d)@ 9\mod_1285229289866_0.docx@ 64941 @ @ 1
WAGO-I/O-SYSTEM 750
Manual
753-540
4DO 230 V AC
4-
channel digital output 230 VAC
V
ersion 1.1.0
Pos: 3 / All e Seri e n ( Al lg e m ein e M od ul e) /R ec htl ic h es , A ll ge mei n es /I mpr e ss um für Sta nd ard h an d büc h er - al lg . A ng a be n, Ansc hri ft en, T elef o nn u m mer n und E -Mai l-Adr es s e n @ 3\mod_1219151118203_21.docx@ 21060@ @ 1

2 WAGO-I/O-SYSTEM 750
753-540 4DO 230 V AC
Manual
Version 1.1.0
© 2017 WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]om
Web: http://www.wago.com
Technical Support
Phone: [phone] – 5 55
Fax: [phone] – 85 55
E-Mail: [email protected]om
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [e-mail]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
=== Ende d er Lis t e f ür Te xt mar ke Ei nb and _ vor n e = = =

WAGO-I/O-SYSTEM 750 Table of Contents 3
753-540 4DO 230 V AC
Manual
Version 1.1.0
Pos: 5 /D o ku ment ati on allg e mei n /Ver zei c hni ss e/I nh alt s verz ei ch nis - Ü b er schr if t oG und Ver zei ch nis @ 3\mod_1219151230875_21.docx@21063 @ @ 1
Table of Contents
1Notes about this Documentation................................................................. 5
1.1 Validity of this Documentation................................................................. 5
1.2 Copyright................................................................................................... 5
1.3 Symbols..................................................................................................... 6
1.4 Number Notation....................................................................................... 8
1.5 Font Conventions ...................................................................................... 8
2Important Notes ........................................................................................... 9
2.1 Legal Bases ............................................................................................... 9
2.1.1 Subject to Changes ............................................................................... 9
2.1.2 Personnel Qualifications....................................................................... 9
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying
Provisions ............................................................................................. 9
2.1.4 Technical Condition of Specified Devices......................................... 10
2.2 Safety Advice (Precautions).................................................................... 11
3Device Description ..................................................................................... 13
3.1 View ........................................................................................................ 15
3.2 Connectors............................................................................................... 16
3.2.1 Data Contacts/Internal Bus................................................................. 16
3.2.2 Power Jumper Contacts/Field Supply ................................................ 17
3.2.3 CAGE CLAMP®Connectors ............................................................. 19
3.3 Display Elements .................................................................................... 20
3.4 Schematic Diagram ................................................................................. 21
3.5 Technical Data ........................................................................................ 22
3.5.1 Device................................................................................................. 22
3.5.2 Supply................................................................................................. 22
3.5.3 Communication .................................................................................. 22
3.5.4 Inputs .................................................................................................. 22
3.5.5 Connection.......................................................................................... 22
3.5.6 Climatic Environmental Conditions................................................... 23
3.6 Approvals ................................................................................................ 24
3.7 Standards and Guidelines........................................................................ 25
4Process Image ............................................................................................. 26
5Mounting..................................................................................................... 27
5.1 Mounting Sequence................................................................................. 27
5.2 Inserting and Removing Devices ............................................................ 28
5.2.1 Inserting the I/O Module .................................................................... 28
5.2.2 Removing the I/O Module.................................................................. 29
5.3 I/O Modules with Pluggable Wiring Level (Series 753) ........................ 30
5.3.1 Coding ................................................................................................ 31
5.3.2 Connector Removal ............................................................................ 33
6Connect Devices ......................................................................................... 34
6.1 Connecting a Conductor to the CAGE CLAMP®................................... 34
7Use in Hazardous Environments .............................................................. 35
7.1 Marking Configuration Examples........................................................... 36

4 Table of Contents WAGO-I/O-SYSTEM 750
753-540 4DO 230 V AC
Manual
Version 1.1.0
7.1.1 Marking for Europe According to ATEX and IEC-Ex ...................... 36
7.1.2 Marking for America According to NEC 500.................................... 41
7.2 Installation Regulations........................................................................... 42
7.2.1 Special Conditions for Safe Use (ATEX Certificate TÜV 07 ATEX
554086 X)........................................................................................... 43
7.2.2 Special Conditions for Safe Use (ATEX Certificate TÜV 12 ATEX
106032 X)........................................................................................... 44
7.2.3 Special Conditions for Safe Use (IEC-Ex Certificate TUN 09.0001 X)45
7.2.4 Special Conditions for Safe Use (IEC-Ex Certificate IECEx TUN
12.0039 X).......................................................................................... 46
7.2.5 Special Conditions for Safe Use According to ANSI/ISA 12.12.01.. 47
List of Figures ...................................................................................................... 48
List of Tables........................................................................................................ 49
=== En de der Lis te für T extmar ke Verz eich nis_vor ne == =

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5
753-540 4DO 230 V AC
Manual
Version 1.1.0
Pos: 7 / All e S eri e n ( All ge mei n e M od ul e) /Üb ers c hri ft en/ Ebe n e 1/H in w eis e z u dies er D o ku me nt ati on - Ü ber sc hr ift 1 @ 4\mod_1237987661750_21.docx@ 29029@ 1 @ 1
1 Notes about this Documentation
Pos: 8 /Al le S eri en ( Allg em ein e Mod ul e)/Si cher h eits- unds onstige Hinweise/Hinweis/Hinweis:Dokumentationaufbewahren@ 4\mod_1237987339812_21.docx @ 29026@ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation is
included, if necessary.
Pos: 9 / All e S er i en ( All g e mei n e M od ul e) /Üb er sc hr i ft en/ E be ne 2/G ülti g kei t sb erei c h - Üb er sc hr ift 2 @ 12\mod_1338912448776_21.docx@ 96469@ 2 @ 1
1.1 Validity of this Documentation
Pos: 10 /S er ie 75 0 ( WA GO -I/O-S YS T EM )/H i n weis e z ur D o kum ent at i on/ G ül tig kei ts b er eic h/G ült igkeitsbereichDokumentationBusklemme750-xxxx, ohne V aria ntena ngabe @ 14\mod_1358944037947_21.docx@109346@ @ 1
This documentation is only applicable to the I/O module 753-540
(4DO 230 V AC).
Pos: 11 /S erie750 (WAGO-I/O-SYST EM )/H i nweis e z ur Do kum ent ati on/H i nw eise /Ac ht ung : H in wei s z ur D o ku ment ati on B us kl emm en 750-xxxx @ 4\mod_1237986979656_21.docx @ 29023@ @ 1
The I/O module 753-540 shall only be installed and operated according to the
instructions in this manual and in the manual for the used fieldbus
coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
Pos: 12.1 /All e Seri en ( Al lg emei ne M o dul e)/Ü ber sc hri fte n/ Ebe ne 2/Ur h eber sc hutz - Über sc hr ift 2 @ 23\mod_1435647042188_21.docx @ 184808@ 2@ 1
1.2 Copyright
Pos: 12.2 /All e Seri en ( Al lg emei ne Mo d ule) /R ec htli ch es , A llg e mei nes /U rh eb ersc hu tz aus führ li ch @ 4\mod_1235565145234_21.docx@ 27691@ @ 1
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos:12.3/Dokumentati on allg e mei n/ Gl i eder ung s el em en te /---Sei t e nwe chs el --- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750
753-540 4DO 230 V AC
Manual
Version 1.1.0
Pos: 12.4 /All e Seri en ( Al lg emei ne M o dul e)/Ü ber sc hri fte n/ Ebe ne 2/S ymbol e - Ü b ers chr if t 2 @ 13\mod_1351068042408_21.docx @ 105270@ 2 @ 1
1.3 Symbols
Pos: 12.5 .1 /All e Serie n( Allg emeine M odul e)/Si cherh eits- und sons t ig e Hi n weis e/ Ge fa hr /G ef a hr: _War nu ng vor P er s on en sch ä de n allg e mei n _ - Er läu ter ung @ 13 \mod_1343309450020_21.docx@ 101029@ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12 .5.2 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti ge H i n weis e/ Gef ahr /G ef ahr : _War nu ng vor P ers on en sch ä de n d urc h el e ktri sc he n St ro m_ - Erläuterung@ 13\mod_1343309694914_21.docx@ 101030@ @ 1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12 .5.3 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons tig e H i n weis e/ W ar nung / W ar nung : _W ar nu ng vor Per sonens chäd en allg emei n_ -Erläuterung@ 13\mod_1343309877041_21.docx@ 101035@ @ 1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos: 12 .5.4 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti g e Hi n weis e/ Vors ic ht /V ors ic ht: _War n ung vor Per s one nsc hä d en al lg em ein _ - Erläuterung@ 13\mod_1343310028762_21.docx@ 101038@ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos: 12 .5.5 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti g e Hi n weis e/ Ac htu ng/ Ac htu ng : _War nu ng vor Sachs c häd en allg e mei n_ - Erläuterung@ 13\mod_1343310134623_21.docx@ 101041@ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12 .5.6 /Al le Seri e n ( Al lg e mei ne Mod ul e)/ Si ch er h eits - u nd so ns ti ge H i n weis e/ Ac htu ng/ Ach tu ng : _ War nu ng vor Sac hsc h äden dur c h el ek tros t atis ch e Aufl adu ng _ - Er l äut er ung @ 13\mod_1343310227702_21.docx@ 101044@ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12 .5.7 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sonstige Hi nweise/Hinweis/Hinweis:_Wichtiger Hin weis allg em ein _ - Erläuterung@ 13\mod_1343310326906_21.docx@ 101047@ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos: 12 .5.8 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und so ns ti g e H i n weis e/ I nf or ma tio n/I nf or ma tio n: _W eit er e I nf or ma ti o n al lg e mei n_ - Erl äu ter ung @ 13 \mod_1343310439814_21.docx@ 101051@ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7
753-540 4DO 230 V AC
Manual
Version 1.1.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos:12.6/Dokumentationallgemein/Gliederungselemente/---Seite nwe chs el--- @ 3\mod_1221108045078_0.docx @ 21810@ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750
753-540 4DO 230 V AC
Manual
Version 1.1.0
Pos: 12.7 /All e Seri en ( Al lg emei ne M o dul e)/Ü ber sc hri fte n/ Ebe ne 2/Dar st ell ung der Z a hle ns yst em e - Ü bers c hri ft 2 @ 23\mod_1435647128078_21.d ocx @ 184 811 @ 2@ 1
1.4 Number Notation
Pos: 12.8 /All e Seri en ( Al lg emei ne Mo d ule) /R ec htli ch es , A llg e mei nes /Z ahl ens y st e me @ 3\mod_1221059454015_21.docx@ 21711@ @ 1
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated with
dots (.)
Pos: 12.9 /All e Seri en ( Al lg emei ne M o dul e)/Ü ber sc hri fte n/ Ebe ne 2/Sc hri ft ko nvent i one n - Ü ber sc hri ft 2 @ 23\mod_1435647186005_21.docx@ 18481 4 @ 2@ 1
1.5 Font Conventions
Pos: 12.1 0 / All e Seri e n ( Al lg e m ein e M o dul e) /R e ch tl ich es , A ll ge m ein es / Sc hr ift k onv e nti on en @ 3 \mod_1221059521437_21.docx@ 21714@ @1
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.: Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]
Pos: 13 /D o ku me nt ati o n al lg e mei n/ Gl ie der ung s ele m e nte /---Seit e n we chs el --- @ 3\mod_1221108045078 _0.doc x@ 2 1810 @ @1

WAGO-I/O-SYSTEM 750 Important Notes 9
753-540 4DO 230 V AC
Manual
Version 1.1.0
Pos: 14 /A ll e Ser i en ( All ge mei ne M od ule) /Ü b ersc hrif te n/ Ebe ne 1/ Wic hti ge Erl äu ter ung en - Ü ber sc hr ift 1 @ 4 \mod_1241428899156_21.docx @ 32170@ 1 @ 1
2 Important Notes
Pos: 15.1 /All e Seri en ( Al lg emei ne M o dul e)/R ec htl ich es , All ge m ei nes/ Wic htig e Er l äut er ung en - Ei nlei t u ng @ 3\mod_1221059818031_21.docx@ 21717@ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 15 .2 /All e Seri en( Allg emeine M odul e)/Ü berschr ifte n/Ebe ne 2/Rec htlic he Gr undlag en - Über sc hr ift 2 @ 3\mod_1221060626343_21.docx@ 21726@ 2 @ 1
2.1 Legal Bases
Pos: 15.3 /All e Seri en ( Al lg emei ne Mo d ule) /R ec htli ch es , A llg e mei nes /Ä nd er ung s vorb eh alt - Üb erschr ift 3 und In halt @ 3\mod_1221060036484_21.docx@ 21720 @ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications that serve to increase the efficiency of technical
progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from
the granting of patents or from the legal protection of utility patents. Third-party
products are always mentioned without any reference to patent rights. Thus, the
existence of such rights cannot be excluded.
Pos:15.4/Serie750(WAGO-I/O-S YST EM )/ Wi c hti g e Er lä ut er u ng en/ Per s on al q ual if i kat io n/ Per s o nalq u ali fi k ati on 750- xxxx - Ü bers chrift 3 u ndI nhalt @ 3\mod_1224061208046_21.docx@ 24063@ 3@ 1
2.1.2 Personnel Qualifications
All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos: 15.5 /Serie750(WAGO-I/O-SYST EM )/ Wi c ht ig e Erlä ut er u ng e n/ Bes ti m mu ng s ge mäß e V er w end ung / B es ti m mu ng sg e m äß e V er we n du ng 75 0- xxxx - Ü bersc hrift 3 u nd Inh alt @ 3\mod_1224064151234_21.docx@ 24070@ 3 @ 1
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions
Fieldbus couplers, fieldbus controllers and I/O modules found in the modular
WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and
transmit them to actuators or higher-level control systems. Using programmable
controllers, the signals can also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO-I/O-SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information
in the section “Device Description” > “Standards and Guidelines” in the manual
for the used fieldbus coupler/controller.

10 Important Notes WAGO-I/O-SYSTEM 750
753-540 4DO 230 V AC
Manual
Version 1.1.0
Appropriate housing (per 2014/34/EU) is required when operating the WAGO-
I/O-SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
Pos: 15.6 /All e Seri en ( Al lg e mei ne M od ule) /R ec htl ic hes , A llg e mei nes /T ec hni sc her Z us t and der Ger ät e - Ü bersc hrift 3 u nd Inh alt @ 3\mod_1221060446109_21.docx@ 21723@ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. WAGO
Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of
changes in hardware or software as well as to non-compliant usage of devices.
Please send your request for modified and new hardware or software
configurations directly to WAGO Kontakttechnik GmbH & Co. KG.
Pos:15.7/Dokumentationallgemein/Gliederungselemente/---Seite nwe chs el--- @ 3\mod_1221108045078_0.docx @ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11
753-540 4DO 230 V AC
Manual
Version 1.1.0
Pos: 15.8 /All e Seri en ( Al lg emei ne M o dul e)/Ü ber sc hri fte n/ Ebe ne 2/Si cher hei t shi nwei s e - Üb ers c hri ft 2 @ 6 \mod_1260180299987_21.docx@ 46724@ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 15.9 /All e Seri en ( Al lg emei ne M o dul e)/ Sich er hei ts- u nd s ons ti ge H i n weis e/ Einl ei t ung Sich er hei ts hin wei s e H ar d war e @ 6\mod_1260180170493_21.docx@ 46720@ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 15.1 0.1 / All e S eri en (Al lg em eine M o dul e)/Si ch erh eits- un d s o nsti g e H in w eis e /G ef a hr/G ef ahr : Nic ht an G er ät e n un ter S pa nnu ng ar bei te n! @ 6\mod_1260180365327_21.docx @ 46727 @ @ 1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: 15.1 0. 2 / S eri e 750 ( W AG O-I/O-SY ST EM)/ Wic htig e Erl äu ter ung en/Si c herhei ts - und s o nsti g e H i n wei se /G ef ahr / Ge fa hr : E i nb au 0 7 50-xx xx nur i n Geh äus en, Sc hrä n ken o der el e ktris c hen Betr ie bsr ä ume n! @ 6\mod_1260180556692_21.docx@ 46731@ @ 1
Install the device only in appropriate housings, cabinets or in electrical
operation rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Pos: 15.1 0.3 / All e S eri en (Al lg em eine M o dul e)/Si ch erh eits- un d s o nsti g e H in w eis e /G ef a hr/G ef ahr : Unf all ver h üt ungs vorschriftenbeachten!@ 6\mod_1260180657000_21.docx@ 46735@ @ 1
Pos: 15.1 0.4 / All e S eri en (Al lg em eine M o dul e)/Si ch erh eits- un d s o nsti g e H in w eis e /G ef a hr/G ef ahr : Auf nor mg er ec ht e n A ns c hl us s acht en! @ 6 \mod_1260180753479_21.docx@ 46739@ @ 1
Pos: 15.1 1.1 / All e S eri en (Al lg em eine M o dul e)/Si ch erh eits- un d s o nsti g e H in w eis e /A cht u ng /Ac ht u ng : D ef e kte oder bes ch ädi gt e Ger ät e austa us c h en! @ 6\mod_1260180857358_21.docx@ 46743 @ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Pos: 15.1 1.2 / All e S eri en (Al lg em eine M o dul e)/Si ch erh eits- un d s o nsti g e H in w eis e /A cht u ng /Ac ht u ng : G erä te vor kri ec he n den und isol i er end en Sto ff en sc hüt ze n! @ 6\mod_1260181036216_21.docx @ 46747 @ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for handling
devices/modules.
Pos: 15.1 1.3 / All e S eri en (Al lg em eine M o dul e)/Si ch erh eits- un d s o nsti g e H in w eis e /A cht u ng /Ac ht u ng : R ei nig u ng n ur mit zul äss ig e n M at er ial i en! @ 6\mod_1260181203293_21.docx@ 46751@ @ 1
Clean only with permitted materials!
Clean soiled contacts using oil-free compressed air or with ethyl alcohol and
leather cloths.
Pos: 15.1 1.4 / All e S eri en (Al lg em eine M o dul e)/Si ch erh eits- unds onstigeHinweise/Achtung/Achtung:KeinKontaktspray verwenden! @ 6\mod_1260181290808_21.docx@ 46755@ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750
753-540 4DO 230 V AC
Manual
Version 1.1.0
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos: 15.1 1.5 / All e S eri en (Al lg em eine M o dul e)/Si ch erh eits- un d s o nst ig e Hin w eis e /A cht u ng /Ac ht u ng : V er pol ung en der Dat en- un d Ver sor g u ng sl eit u ng en ver m eid e n! @ 6\mod_1260184045744_21.docx@ 46767 @ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos: 15.1 1.6 / All e S eri en (Al lg em eine M o dul e)/Si ch erh eits- un d s o nsti g e H in w eis e /A cht u ng /Ac ht u ng : El e ktr os t atis c h e En tl a du ng verm ei de n! @ 6\mod_1260181364729_21.docx@ 46759 @ @ 1
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
Pos: 16 /D o ku me nt ati o n al lg e mei n/ Gl ie der ung s ele m e nte /---Seit e n we chs el --- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 13
753-540 4DO 230 V AC
Manual
Version 1.1.0
Pos: 17 /Al l e Seri en (All g emei n e M o d ule) /Ü b er schr i f te n/ Eb ene 1/G er ät e bes chr eib ung - Ü ber sc hri f t 1 @ 3\mod_1233756084656_21.docx@ 27096 @ 1 @ 1
3 Device Description
Pos:18.1/Serie750(WAGO-I/O-S YST EM) /Ger äte b esc hrei bu ng/E i nlei tu ng/A n wen dung /D O/A n wen dung 7 50-x5xxD O @ 3\mod_1233764594468_21.docx@ 27120@ @ 1
The 753-540 (4DO 230 V AC) Digital Output Module transmits binary control
signals from the automation device to the connected actuators (e.g., solenoid
valves, contactors, transmitters, relays or other electrical loads).
Pos:18.2/Serie750(WAGO-I/O-SYSTE M)/ Ger ät eb esc hrei bu ng /Ei nlei tu ng/ I/O -Bes c hrei bu ng /DO / I /O -Besc hr ei b ung 750-05xx 4 D O 2-Leit er ( D O u n d N) @ 17\mod_1380188858999_21.docx@ 132837@ @ 1
The module has four output channels. Four 2-conductor actuators may be directly
connected to the module. The actuators can be connected using connection DO 1
and N … DO 4 and N.
Pos:18.3/Serie750(WAGO-I/O-S YST EM) /Ger äte b esc hrei bu ng/E i nlei tu ng/I /O-B es c hr ei bu ng / Al lg em ei n/V er wei s auf Ka pit el "A nsc hl üss e" @ 8\mod_1276775378035_21.docx @ 57956 @ @ 1
The assignment of the connections is described in the “Connectors” section.
Pos:18.4/Dokumentationallgemein/Gliederungselemente/---Leerabs at z-(2Z)--- @ 3 \mod_1224662755687_0.docx@ 24460@ @ 1
Pos:18.5/Serie750(WAGO-I/O-SYST EM) / Ger ät eb esc hrei bu ng /Ei nlei tu ng/ I/O -Bes c hrei bu ng /DO /I / O-B esc hr ei bu ng 750-x5 xx D O H SS / pos i ti vschal t end (120 /2 30 V) @ 17\mod_1380190889078_21.docx@ 132841@ @ 1
The I/O module outputs provide high-side switching. If the signal status of an
output channel is at "high" the 120 (230) V potential for field power will be
switched to the appropriate output connection.
Pos:18.6/Serie750(WAGO-I/O-S YST EM) /Ger äte b esc hrei bu ng/E i nlei tu ng/L ED-A nz eig e/ LED Zu st an d Sig nal @ 3\mod_1233755258578_21.docx @ 27087@ @ 1
A green LED indicates the switched status of each channel.
Pos:18.7/Serie750(WAGO-I/O-S YST EM) /Ger äte b esc hrei bu ng/E i nlei tu ng/L ED-A nz eig e/ Ver w eis auf Kapi t el "Anz ei g e ele m en te" @ 5\mod_1246010525000_21.docx@ 36194@ @ 1
The meaning of the LEDs is described in the “Display Elements” section.
Pos:18.8/Serie750(WAGO-I/O-S YST EM )/ Wi c hti g e Er lä ut er u ng en/ Si ch er h eits - u nd so nst ig e H in wei s e/Hi n wei s/Hi n wei s: Eins pei se kl em me f ür die Ver sor gu ng mit AC 12 0 ( 23 0) V s etz e n! @ 20\mod_1412677533928_21.docx@ 165323 @ @ 1
A supply module must be added for operation with 120 VAC or 230 VAC!
Use an additional supply module to operate the I/O module 753-540 with 120
VAC / 230 VAC. Place the supply module immediately before the I/O module
753-540.
Pos:18.9/Serie750(WAGO-I/O-S YST EM )/ G er äte b esc hr ei bu ng /Ei nlei tu ng /V er s org ung / Ver s or gu ng AC 1 20 /2 3 0 V üb er Leis t ung s ko nt a kte @ 16 \mod_1379941216895_21.docx@ 132504@ @ 1
The I/O module receives the 120 V/230 V potential for field power and the N
potential for the field level from an upstream power supply module via the power
contacts used as blade contacts. It then provides this potential to subsequent I/O
modules via the power contacts used as spring contacts.
Pos: 18.1 0 / S eri e 750 ( W AG O-I/ O-SYST EM) /Wi chtig e Er l äuter ung en /Sic her hei ts- und s o nsti g e H in wei se /Ac ht ung /Ac ht ung : Maxi m aler Str o m Lei s tu ngs ko nt ak te 1 0 A @ 3\mod_1226499143500_21.docx@ 25029 @ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos: 18.1 1 / S eri e 750 ( W AG O-I/ O-SYST EM) /Wi chtig e Er l äuter ung en /Sic her hei ts- und s o nsti g e H in wei se /Ac ht ung /Ac ht ung : DO Ü ber las t sc hut z - Einpeiseklemmemit Sicherung@ 3\mod_1233814881117_21.docx@ 27150@ @ 1
Provide for overload protection!
Overloading can damage the electronic components of the I/O module.
A fused supply module (750-601) must be installed upstream of the I/O module to
protect it against overloading!
Pos: 18.1 2 / S eri e 750 ( W AG O-I/ O-SYST EM) /Wi chtig e Er l äuter ung en /Sic her hei ts- und s o nsti g e H in wei se /Hi nw eis /Hi n weis : P ot e nti alei n sp eis e kle mm e f ür Erd e ei ns etz e n! ( kei ne LK f ür Er de) @ 3\mod_1226499037468_21.docx@ 25023@ @ 1

14 Device Description WAGO-I/O-SYSTEM 750
753-540 4DO 230 V AC
Manual
Version 1.1.0
Use supply modules for ground (earth)!
The I/O module has no power jumper contacts for receiving and transmitting the
earth potential. Use a supply module when an earth potential is needed for the
subsequent I/O modules.
Pos: 18.1 3 / S eri e 750 ( W AG O-I/ O-SYST EM ) /G erät e be sc hr ei b ung /E i nl eit ung / V ers org u ng /G al v anis c h e T re n nu ng F eld/System@ 3\mod_1233756478750_21.docx@ 27102@ @ 1
The field voltage and the system voltage are electrically isolated from each other.
Pos: 18.1 4 / S eri e 750 ( W AG O-I/ O-SYST EM ) /G erät e be sc hr ei b ung /E i nl eit ung / V ers org u ng /A n ord nu ng unt er Ber üc ksi c htig u ng der Lei st ung s k ont ak t e b el ie bi g @ 3\mod_1233756233468_21.docx@ 27099 @ @ 1
With consideration of the power jumper contacts, the individual modules can be
arranged in any combination when configuring the fieldbus node. An arrangement
in groups within the group of potentials is not necessary.
Pos: 18.1 5 / S eri e 750 ( W AG O-I/ O-SYST EM ) /G erät e be sc hr ei b ung /E i nl eit ung / Ei ns a tzb er eic h/ Ei n sa tzb er eic h 7 50-x xxx alle Kop pler /C ont roll er oh ne Ei ns chr ä nkung @ 3\mod_1232541691906_21.docx@ 26522 @ @ 1
The I/O module 753-540 can be used with all fieldbus couplers/controllers of the
WAGO-I/O-SYSTEM 750.
Pos: 19 /D o ku me nt ati o n al lg e mei n/ Gl ie der ung s ele m e nte /---Seit e n we chs el --- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15
753-540 4DO 230 V AC
Manual
Version 1.1.0
Pos: 20 /A lle Ser ien (Al lg e mei n e M od ul e)/ Ü b ers chr if t en/ Eb e ne 2/A nsi c ht - Ü b er sc hri f t 2 @ 4\mod_1240984217343_21.docx@ 31958@ 2@ 1
3.1 View
Pos: 21 /S er ie 75 3 ( WA GO -I/O-S YS T EM )/ Ger ät eb esc hr ei bu ng /A ns ic ht /D i gi tal aus g ang s kl em m en/ A nsic ht 75 3-054 0 @ 17\mod_1380195681747_21.docx@ 132845@ @ 1
Figure 1: View
Pos: 22 /S er ie 75 3 ( WA GO -I/O-S Y ST EM ) / Ger ät ebes c hr ei bu ng /A ns ic ht /A nsi c ht – Leg en d e mi t Leis t ungs kon ta kt en _ mit Kodi er ung , K a bel be fe st ig u ng u nd Pr üf öff n ung en @ 20 \mod_1411031302199_21.docx @ 163871@ @ 1
Table 3: Legend for Figure “View”
Pos.
Description
Details See Section
1
Marking possibility with Mini-
WSB
---
2
Status-LEDs
“Device Description” > “Display
Elements”
3
Data contacts
“Device Description” > “Connectors”
4
CAGE CLAMP®connectors
“Device Description” > “Connectors”
5
Pull tab
“Mounting” > “I/O Modules with
Pluggable Wiring Level (Series 753)”
6
Coding possibility with coding
fingers
“Mounting” > “Coding”
7
Power jumper contacts
“Device Description” > “Connectors”
8
Test port
---
9
Fixing lug for cable ties
“Mounting” > “I/O Modules with
Pluggable Wiring Level (Series 753)”
Pos: 23 /D o ku me nt ati o n al lg e mei n/ Gl ie der ung s ele m e nte /---Seit e n we chs el --- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

16 Device Description WAGO-I/O-SYSTEM 750
753-540 4DO 230 V AC
Manual
Version 1.1.0
Pos: 24 /A ll e Ser i en ( All ge mei ne M od ule) /Ü b ersc hrif te n/ Ebe ne 2/ A nsc hlüs se - Ü ber sc hr ift 2 @ 4 \mod_1240984262656_21.docx @31961 @ 2@ 1
3.2 Connectors
Pos: 25 /S er ie 75 0 ( WA GO -I/O-S YS T EM )/ Ger ät eb esc hr ei bu ng /A ns c hl üss e/D at en k ont ak t e/Kl e m men bu s - Ü ber sc hr ift 3 @ 6\mod_1256294684083_21.docx@ 43660@ 3 @ 1
3.2.1 Data Contacts/Internal Bus
Pos:26.1/Serie750(WAGO-I/O-S YST EM ) / Ger äte b esc hr ei bu ng /A ns c hl üss e/ Da te n k ont a kt e - F el dbu s kop pler /-c on tr ol l er , A b bil d ung und Bes c hr ei bu ng @ 3 \mod_1231771259187_21.docx@ 26002@ @1
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the internal bus. It
is comprised of 6 data contacts, which are available as self-cleaning gold spring
contacts.
Figure 2: Data Contacts
Pos:26.2/Serie750(WAGO-I/O-SYST EM) / Wic ht ig e Erlä ut er u nge n/ Si ch er hei ts - und sons ti g e H in wei s e/ Ac ht ung /A c h tu ng: Bus kl em m en ni c ht auf Gol df e der kon ta k t e l eg en! @ 7 \mod_1266318463636_21.docx@ 50695 @ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos:26.3/Serie750(WAGO-I/O-S YST EM )/ Wi c hti g e Er lä ut er u ng en/ Si ch er h eits - und sonstigeHinweise/Achtung/Achtung:ESD- A uf g ut e Erd ung der Umg eb u ng ac ht e n! @ 7\mod_1266318538667_21.docx@ 50708@ @ 1
Ensure that the environment is well grounded!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, ensure that the environment
(persons, workplace and packing) is well grounded. Avoid touching conductive
components, e.g. data contacts.
Pos: 27 /D o ku me nt ati o n al lg e mei n/ Gl ie der ung s ele m e nte /---Seit e n we chs el --- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17
753-540 4DO 230 V AC
Manual
Version 1.1.0
Pos: 28 /S er ie 75 0 ( WA GO -I/O-S YS T EM )/ Ger ät eb esc hr ei bu ng /A ns c hl üss e/L eis t u ngs kont a kte/ F el d vers or g u ng - Ü b ersc hr if t 3 @ 6\mod_1256294692864_21. doc x@ 43 664 @ 3 @ 1
3.2.2 Power Jumper Contacts/Field Supply
Pos:29.1/Serie750(WAGO-I/O-S YST EM )/ Wi c hti g e Er lä ut er u ng en/ Si ch er h eits - u nd so nst ig e H in wei s e/ Vors ic ht/ V ors ich t: Verl etz ung sg e fa hr durc h s c har f kan tig e M ess er kont a kte! @ 6\ mod_1256193279401_21.docx@ 43414@ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
Pos:29.2/Serie750(WAGO-I/O-S YST EM )/ G er äte b esc hr ei bu ng /A nsc hl üs se /L eis t u ngs kont a kte 2 LK (Mes s er/ F e der) - Einl eitu ng @ 1 5\mod_1371721641099_21.docx@ 123714@ @ 1
The I/O module 753-540 has 2 self-cleaning power jumper contacts that supply
and transmit power for the field side. The contacts on the left side of the I/O
module are designed as blade contacts and those on the right side as spring
contacts.
Pos:29.3/Serie753(WAGO-I/O-S YST EM) / Ger äte b esc hr ei bung /A nsc hl üs se /L eist u ng s kont akt e/F el dv ers or gu ng 2 L K ( Mes s er/ F eder ) - Abbildung@ 17\mod_1381924880242_21.docx@ 134239@ @ 1
Figure 3: Power Jumper Contacts
Pos:29.4/Serie750(WAGO-I/O-S YST EM )/ G er äte b esc hr ei bu ng /A nsc hl üs se /L eis t u ngs kont a kte 2 LK (Mes s er/ F e der) - Leg end e @ 1 5\mod_1371721352500_21.docx@ 123710@ @ 1
Table 4: Legend for Figure “Power Jumper Contacts”
Contact
Type
Function
1
Spring contact
Potential transmission (Uv) for field supply
2
Spring contact
Potential transmission (0 V) for field supply
3
Blade contact
Potential feed-in (0 V) for field supply
4
Blade contact
Potential feed-in (Uv) for field supply
Pos:29.5/Serie750(WAGO-I/O-S YST EM )/ Wi c hti g e Er lä ut er u ng en/ Si ch er h eits - u nd s ons ti g e H in wei s e/ Ac ht ung /A c h tu ng: M a xi mal er S tr o m L ei st ung s kon ta k t e 10 A @ 3\mod_1226499143500_21.docx@ 25029@ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos:29.6/Serie750(WAGO-I/O-S YST EM )/ Wi c hti g e Er lä ut er u ng en/ Si ch er h eits - u nd s ons tig e H in wei s e/Hin wei s/H i nw eis: Pote nti al ei nspei s ekl e mme f ür E rd e ei ns etz en! ( keine LK für E rd e) @ 3\mod_1226499037468_21.docx@ 25023 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750
753-540 4DO 230 V AC
Manual
Version 1.1.0
Use supply modules for ground (earth)!
The I/O module has no power jumper contacts for receiving and transmitting the
earth potential. Use a supply module when an earth potential is needed for the
subsequent I/O modules.
Pos: 30 /D oku ment ation all g emei n/ Gli e der ung s el e me nte /---Sei t e n wechs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19
753-540 4DO 230 V AC
Manual
Version 1.1.0
Pos: 31 /S er ie 75 0 ( WA GO -I/O-S Y ST EM ) / Ger ät ebes c hr ei bu ng /A ns c hl üss e/ CA GE CL AM P-An schl üs s e - Ü b er sc hri f t 3@ 6\mod_1256296337770_21.docx@ 43674 @ 3 @ 1
3.2.3 CAGE CLAMP®Connectors
Pos: 32 /S er ie 75 3 ( WA GO -I/O-S YST E M) /G er ät ebes c hrei bu ng /A nsc hl üss e/ Di gi tal ausg ang s kl em men/ An sc hl üss e 753-0540@ 17\mod_1382014303471_21.docx@ 134384@ @ 1
Figure 4: CAGE CLAMP®Connectors
Table 5: Legend for Figure “CAGE CLAMP®Connectors”
Channel
Designation
Connector
Function
1
DO 1
1
Output DO 1: Signal voltage
-
N
2
Neutral wire
-
N
3
Neutral wire
3
DO 3
4
Output DO 3: Signal voltage
2
DO 2
5
Output DO 2: Signal voltage
-
N
6
Neutral wire
-
N
7
Neutral wire
4
DO 4
8
Output DO 4: Signal voltage
Pos: 33 /D o ku me nt ati o n al lg e mei n/ Gl ie der ung s ele m e nte /---Seit e n we chs el --- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750
753-540 4DO 230 V AC
Manual
Version 1.1.0
Pos: 34 /A ll e Ser i en ( All ge mei ne M od ule) /Ü b ersc hrif te n/ Ebe ne 2/ A nzeig eel e ment e - Ü b ers chr if t 2 @ 4\mod_1240984390875_21.docx@ 31964 @ 2@ 1
3.3 Display Elements
Pos: 35 /S er ie 75 0 ( WA GO -I/O-S Y ST EM ) / Ger ät ebes c hr ei bu ng /A nz eig e el e men te / Di g ital a usgangsklemmen/Anzeigeelemente750-05xx4DO@ 11\mod_1322035869631_21.docx@ 83554@ @ 1
Figure 5: Display Elements
Table 6: Legend for Figure “Display Elements”
Channel
Designation
LED
State
Function
1 Status DO 1 A
Off
Output DO 1: Signal voltage “0”
Green
Output DO 1: Signal voltage “1”
2 Status DO 2 C
Off
Output DO 2: Signal voltage “0”
Green
Output DO 2: Signal voltage “1”
3 Status DO 3 B
Off
Output DO 3: Signal voltage “0”
Green
Output DO 3: Signal voltage “1”
4 Status DO 4 D
Off
Output DO 4: Signal voltage “0”
Green
Output DO 4: Signal voltage “1”
Pos: 36 /D o ku me nt ati o n al lg e mei n/ Gl ie der ung s ele m e nte /---Seit e n we chs el --- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1