WAGO I/O-SYSTEM 750 User manual

Pos:2/Dokumentationallgemein/Einband/EinbandHandbuch- D e c kbl at t ohne Varia nt en fel d(S ta n dar d)@ 9\mod_1285229289866_0.docx @ 64941 @ @ 1
Manual
WAGO-I/O-SYSTEM 750
4DO 24V DC 0.5A/ 2-conductor
750-531(/xxx-xxx)
4-Channel Digital Output Module 24 VDC; 2-
Conductor Connection; Short-circuit-protected; High-
side Switching
Version 1.3.0
Pos: 3 /Al le Ser ie n ( All ge m ein e M od ul e) /Hi nw eis e z ur Doku m ent ati o n/I mpr es su m für Sta nd ard h and büc h er - al lg. Ang aben, A nschr iften, Tel efo nnummer n und E-Mai l-Adr es s e n @ 3\mod_1219151118203_21.docx@ 21060@ @ 1

2 WAGO-I/O-SYSTEM 750
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
© 2015 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]om
Web: http://www.wago.com
Technical Support
Phone: [phone] – 5 55
Fax: [phone] – 85 55
E-Mail: [email protected]om
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [e-mail]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
=== Ende d er List e f ür T e xtm ar ke E i nb a nd_ v orn e == =

WAGO-I/O-SYSTEM 750 Table of Contents 3
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
Pos: 5 /D o ku ment ati on allg em ein /V er zeic h nis se /I nhal ts ver z eic hni s - Ü b ersc hri ft oG u nd V er zei ch nis @ 3\mod_1219151230875_21.docx@21063 @ @ 1
Table of Contents
1Notes about this Documentation................................................................. 5
1.1 Validity of this Documentation................................................................. 5
1.2 Copyright................................................................................................... 5
1.3 Symbols..................................................................................................... 6
1.4 Number Notation....................................................................................... 8
1.5 Font Conventions ...................................................................................... 8
2Important Notes ........................................................................................... 9
2.1 Legal Bases ............................................................................................... 9
2.1.1 Subject to Changes ............................................................................... 9
2.1.2 Personnel Qualifications....................................................................... 9
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying
Provisions ............................................................................................. 9
2.1.4 Technical Condition of Specified Devices......................................... 10
2.2 Safety Advice (Precautions).................................................................... 11
3Device Description ..................................................................................... 13
3.1 View ........................................................................................................ 15
3.2 Connectors............................................................................................... 16
3.2.1 Data Contacts/Internal Bus................................................................. 16
3.2.2 Power Jumper Contacts/Field Supply ................................................ 17
3.2.3 CAGE CLAMP®Connectors ............................................................. 19
3.3 Display Elements .................................................................................... 20
3.4 Operating Elements................................................................................. 20
3.5 Schematic Diagram ................................................................................. 21
3.6 Technical Data ........................................................................................ 22
3.6.1 Device Data ........................................................................................ 22
3.6.2 Power Supply...................................................................................... 22
3.6.3 Communication .................................................................................. 22
3.6.4 Outputs ............................................................................................... 22
3.6.5 Connection Type ................................................................................ 22
3.6.6 Climatic Environmental Conditions................................................... 23
3.7 Approvals ................................................................................................ 24
3.8 Standards and Guidelines........................................................................ 26
4Mounting..................................................................................................... 27
4.1 Mounting Sequence................................................................................. 27
4.2 Inserting and Removing Devices ............................................................ 28
4.2.1 Inserting the I/O Module .................................................................... 28
4.2.2 Removing the I/O Module.................................................................. 29
5Connect Devices ......................................................................................... 30
5.1 Connecting a Conductor to the CAGE CLAMP®................................... 30
5.2 Connection Example ............................................................................... 31
5.2.1 2-Conductor Connection .................................................................... 31
6Process Image ............................................................................................. 32
7Using Interference-Free Variants of I/O Modules in Safety Related
Applications................................................................................................ 33

4 Table of Contents WAGO-I/O-SYSTEM 750
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
7.1 Important Notes....................................................................................... 34
7.2 Connecting the IO Module to Safety Switching Devices or Safety
Modules................................................................................................... 35
7.2.1 General Structure................................................................................ 35
7.2.2 Examples of Connection..................................................................... 36
8Use in Hazardous Environments .............................................................. 38
8.1 Marking Configuration Examples........................................................... 39
8.1.1 Marking for Europe According to ATEX and IEC-Ex ...................... 39
8.1.2 Marking for America According to NEC 500.................................... 44
8.2 Installation Regulations........................................................................... 45
8.2.1 Special Conditions for Safe Use (ATEX Certificate TÜV 07 ATEX
554086 X)........................................................................................... 46
8.2.2 Special Conditions for Safe Use (ATEX Certificate TÜV 12 ATEX
106032 X)........................................................................................... 47
8.2.3 Special Conditions for Safe Use (IEC-Ex Certificate TUN 09.0001 X)48
8.2.4 Special Conditions for Safe Use (IEC-Ex Certificate IECEx TUN
12.0039 X).......................................................................................... 49
8.2.5 Special Conditions for Safe Use According to ANSI/ISA 12.12.01.. 50
List of Figures ...................................................................................................... 51
List of Tables........................................................................................................ 52
=== En de der Lis te für T extmar ke Verz eich nis_vor ne == =

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
Pos: 7 /Al le Seri en ( All ge mei ne M od ul e)/ Üb ersc hr ift en f ür al l e S eri en/H i nwei se zur D o ku ment ati on /Hi nw eise zu dies er D o kum ent atio n - Ü b er sc hri f t 1@ 4\mod_1237987661750_21.docx@ 29029 @ 1@ 1
1 Notes about this Documentation
Pos: 8 /Al le Ser ie n ( All ge m ein e M od ul e) /Hi nw eis e z ur Doku m ent ati o n/Hi n weis e/H i n weis : D o kum ent ati on auf be wahr e n @ 4\mod_1237987339812_21.docx@ 29026 @ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation is
included, if necessary.
Pos: 9 /Al le S eri en ( Allg em eine M od ul e)/Ü bers chr ift en für all e S erie n/Hi n weis e zur Do ku ment ation /G ültig kei tsb erei ch - Ü b ers chr if t 2 @ 12\mod_1338912448776_21.docx@ 96469@ 2 @ 1
1.1 Validity of this Documentation
Pos: 10 / S eri e 750 ( WA GO-I/ O-SYST EM )/ Hi n weis e z ur Do kum e ntat i on/ Gül ti gk eits b erei c h/G ülti g k eits ber ei ch Dok um ent ati o n Bus kl e mme 750-x xxx, Sta n dar d versi on und aufg eli st et e V ari a nt e n @ 14\mod_1358944038682_21.docx @ 109354@ @ 1
This documentation is only applicable to the I/O module 750-531 (4DO 24V DC
0.5A/ 2-conductor) and the variants listed in the table below.
Pos: 11 / S eri e 750 ( WA GO-I/ O-SYST EM) /Hi n weis e z ur D o kum e nt ati on/ G ül ti gk eits b erei c h/ Var ia nt e nli st en/ V ar ia nt enl is t e - 7 50-xxx - Standardversion undVariante/000-800 (rüc k wir kung sfr ei) @ 1 0\mod_1302671594038_21.docx@ 71910@ @ 1
Table 1: Variants
Item Number/Variant
Designation
750-531
4DO 24V DC 0.5A/ 2-conductor
750-531/000-800
4DO 24V DC 0.5A/ 2-conductor/R
Pos: 12 /Al l e Ser i en ( All ge mei ne M od ule) /Hi n weis e zur D o ku ment ati on/ Hin wei se /Hi nw eis: Gül tig keit der Angaben füraufgelisteteVarianten@ 9\mod_1281520778141_21.docx@ 63085@ @ 1
Documentation Validity for Variants
Unless otherwise indicated, the information given in this documentation applies to
listed variants.
Pos: 13 / S eri e 750 ( WA GO-I/ O-SYST EM )/H i nweis e z ur D o kum ent ati on/H i nw eise /Ac ht ung : H in wei s z ur D o ku ment ati on B us kl emm en 750-xxxx @ 4\mod_1237986979656_21.docx @ 29023@ @ 1
The I/O module 750-531 shall only be installed and operated according to the
instructions in this manual and in the manual for the used fieldbus
coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
Pos: 14.1 /All e S eri en ( Al lg emei ne Mod ule) /Hi n weis e z ur D o ku ment ati on /Ur heb ers c hutz ausf ühr lic h @ 4\mod_1235565145234_21.docx@ 27691@ 2 @ 1
1.2 Copyright
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos:14.2/Dokumentationallgemein/Gliederungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
Pos: 14.3 /All e S eri en ( Al lg emei ne Mod ule) /Ü bers chr ift e n f ür alle S er ie n/Hi nw eis e z ur D ok um enta tio n/ Sy mbol e - Ü ber sc hr if t 2 @ 1 3\mod_1351068042408_21.docx @ 105270@ 2@ 1
1.3 Symbols
Pos: 14.4 .1 / All e Serie n ( Al l ge mei ne Mod ul e) / Wic hti g e Er l äut er u ng e n/ Sic her h eit s- und sonstigeHinweise/Gefahr/Gefahr:_WarnungvorPersonenschädenallgemein_- Er l äuter ung @ 13 \mod_1343309450020_21.docx@ 101029@ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 14 .4.2 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so ns ti ge H in wei s e/ Gef ahr /G ef ahr : _War nung vor Pers on en sch ä den durc h el e ktr isc he n Strom _ - Erläuterung@ 13\mod_1343309694914_21.docx@ 101030@ @ 1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 14 .4.3 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- undsonstigeHinweise/W ar n ung/ W ar n ung: _W arn u ng vor P er so ne nsc h äd e n al l ge m ei n_ - Erläuterung@ 13\mod_1343309877041_21.docx@ 101035@ @ 1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos: 14 .4.4 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so ns ti ge H in wei s e/ Vors ic ht /V ors ich t: _War nu ng vor P ers on e nsc hä den allg e mei n_ - Erläuterung@ 13\mod_1343310028762_21.docx@ 101038@ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos: 14 .4.5 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- undsonstigeHinweise/Achtung/Achtung:_Warnung vorSachschäden allgemein_- Erläuterung@ 13\mod_1343310134623_21.docx@ 101041@ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 14 .4.6 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so ns ti ge H in wei s e/ Ach tu ng/ Ach tu ng : _ War nu ng vor S ac hsc hä d en d urc h elektr os t atis c he Aufla du ng _ - Erläuterung@ 13\mod_1343310227702_21.docx@ 101044@ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 14 .4.7 /Al le Seri en (All gemei ne Mod ul e) / Wic hti g e Er l äut er u ng e n/ Sic her h eit s- und so nstige Hinweise/Hinweis/Hinweis:_ WichtigerHi nweis allgemein_ - Erläuterung@ 13\mod_1343310326906_21.docx@ 101047@ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos: 14 .4.8 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so ns t ig e Hi n wei s e/I nf or mat io n/I nf or mat io n: _Wei ter e I nf or ma tio n allg e mei n_ - Er l äu ter ung @ 13 \mod_1343310439814_21.docx@ 101051@ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos:14.5/Dokumentationall ge mei n/ G li e der ung s el em en te /---Sei t en we chs el --- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
Pos: 14.6 /All e S eri en ( Al lg emei ne Mod ule) /Hi n weis e z ur D o ku ment ati on /Za hle ns yst eme @ 3\mod_1221059454015_21.docx@ 21711@ 2 @ 1
1.4 Number Notation
Table 2: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated with
dots (.)
Pos: 14.7 /All e S eri en ( Al lg emei ne Mod ule) /Hi n weis e z ur D okumentation/Schriftkonventionen@ 3\mod_1221059521437_21.docx@ 21714@ 2@ 1
1.5 Font Conventions
Table 3: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.: Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]
Pos: 15 / D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx @ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 9
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
Pos: 16 /Al l e Ser i en ( All ge mei ne M od ule) /Ü b ersc hri fte n f ür all e S er i en/ Wi ch ti g e Er lä ut er u ng en/ Wi ch ti g e Er l äut er u ng en - Ü ber sc hr ift 1 @ 4\mod_1241428899156_21.docx@ 32170@ 1 @ 1
2 Important Notes
Pos: 17 .1 /All e Seri en( Allg emeine D okum ente) ( Allg emeine M odule) /Wic htige Er läut erung en/Ei nleit ung Wic htige E rläut erung en @ 3\mod_1221059818031_21.docx@ 21717@ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 17 .2 /All e Seri en( Allg emeine M odul e)/Ü berschr ifte nf ür alle S erie n/Wich tige Er läuter ung enRec htlic he Grun dlag en -Ü ber sc hr ift 2 @ 3\mod_1221060626343_21.docx@ 21726@ 2 @ 1
2.1 Legal Bases
Pos:17.3/AlleSerien(AllgemeineDokumente) (AllgemeineModule)/WichtigeErläuterungen/Änderungsvorbehalt- Über schr ift 3 und In halt @ 3\mod_1221060036484_21.docx@ 21720@ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications that serve to increase the efficiency of technical
progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from
the granting of patents or from the legal protection of utility patents. Third-party
products are always mentioned without any reference to patent rights. Thus, the
existence of such rights cannot be excluded.
Pos:17.4/Serie750(WAGO-I/O-S YST EM )/ Wi c hti g e Er lä ut er u ng en/ Per s on al q ual if i kat io nP ers on alq u ali fi ka ti on 750- xxxx - Ü ber sc hri ft 3 u nd Inhal t @ 3\mod_1224061208046_21.docx@ 24063@ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos:17.5/Serie750(WAGO-I/O-SYSTEM)/WichtigeErläuterungen/Bestimmungsgemäße VerwendungBestimmungsgemäßeVerwendung750-xxxx - Ü b ers chr if t 3 un d I n hal t @ 3\mod_1224064151234_21.docx@ 24070 @3 @ 1
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions
Fieldbus couplers, fieldbus controllers and I/O modules found in the modular
WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and
transmit them to actuators or higher-level control systems. Using programmable
controllers, the signals can also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO-I/O-SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information
in the section “Device Description” > “Standards and Guidelines” in the manual
for the used fieldbus coupler/controller.

10 Important Notes WAGO-I/O-SYSTEM 750
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-
SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
Pos: 17 .6 /All e Seri en( Allg emeine D okum ente) ( Allg emeine M odule) /Wic htige Er läut erung en/T echnis cher Z ustan d der Ger äte - Übers chri ft 3 und Inh alt @ 3\mod_1221060446109_21.docx@ 21723@ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. WAGO
Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of
changes in hardware or software as well as to non-compliant usage of devices.
Please send your request for modified and new hardware or software
configurations directly to WAGO Kontakttechnik GmbH & Co. KG.
Pos:17.7/Dokumentationall ge mei n/ G li e der ung s el em en te /---Sei t en we chs el --- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
Pos: 17.8 /All e S eri en ( Al lg emei ne Mod ule) /Ü bers chr ift e n f ür alle S er ie n/Wi ch tig e E rlä uter u ngen Sic her hei t shi nwei s e - Üb ers c hri ft 2 @ 6 \mod_1260180299987_21.docx@ 4 6724 @ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 17.9 /All e S eri en ( Al lg emei ne Doku m ente) (Al lg emei ne Mod ule) /Wi c htig e Er lä ut eru nge n/ Sich erh eits hi n weis e/ Einl ei tung Sic her hei ts hi nw eis e H ar dw are @ 6\mod_1260180170493_21.docx @ 46720 @ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 17.1 0. 1 / Al l e S er ie n ( All g em ei ne D o ku ment e) (All g em ei ne M o dul e) / Wich ti g e E rl ä uter u ng en /Sic h erh ei ts hi nw eis e /G ef ahr /G ef ahr : Nich t an G erät e n un ter Spa nnung ar beit en! @ 6\mod_1260180365327_21.docx@ 46727@ @ 1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: 17.1 0. 2 / S er ie 750 ( W AG O-I/O-SY ST EM)/ Wic htig e Er läu ter ung en/S ic herhei ts - und s o nsti g e H i n w eise /G ef ahr / Ge fa hr : Einb au 0 7 50-xx xx nur i n Geh äus en, Sc hrä nke n o der el ektr isc he n Betri ebs rä u men! @ 6\mod_1260180556692_21.docx @ 46731@ @ 1
Install the device only in appropriate housings, cabinets or in electrical
operation rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Pos: 17.1 0. 3 / Al l e S er ie n ( All g em ei ne D o ku ment e) (All g em ei ne M o dul e) / Wich ti g e E rl ä uter u ng en /Sic h erh ei ts hi nw eis e /G ef ahr /G ef ahr : Unfal l v erh üt ung s v ors c hri ftenbeachten!@ 6\mod_1260180657000_21.docx@ 46735@ @ 1
Pos: 17.1 0. 4 / Al l e S er ie n ( All g em ei ne D o ku ment e) (All g em ei ne M o dul e) / Wich ti g e E rl ä uter u ng en /Sic h erh ei ts hi nw eis e /G ef ahr /G ef ahr : Auf normg erec ht e n A ns c hlu ss ac ht en! @ 6\mod_1260180753479_21.docx @ 46739@ @ 1
Pos: 17.1 1. 1 / Al l e S er ie n ( All g em ei ne D o ku ment e) (All g em ei ne M o dul e) / Wich ti g e E rl ä uter u ng en /Sic h erh ei ts hi nw eis e /Ac ht u ng /Ac ht u ng : De fe k t e od er besc h ädig t e Gerät e austa us c h en! @ 6\mod_1260180857358_21.docx @ 46743@ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Pos: 17.1 1. 2 / Al l e S er ie n ( All g em ei ne D o ku ment e) (All g em ei ne M o dul e) / Wich ti g e E rl ä uter u ng en /Sic h erh ei ts hi nw eis e /Ac ht u ng /Ac ht u ng : G erä te vor kriec he nde n und i s ol ier e nden Sto ff en schüt z en! @ 6\mod_1260181036216_21.docx@ 46747 @ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for handling
devices/modules.
Pos: 17.1 1. 3 / Al l e S er ie n ( All g em ei ne D o ku ment e) (All g em ei ne M o dul e) / Wich ti g e E rl ä uter u ng en /Sic h erh ei ts hi nw eis e /Ac ht u ng /Ac ht u ng : Rei nig u ng nur mit zul äss ig e n M at er ial ie n! @ 6\mod_1260181203293_21.docx @ 46751@ @ 1
Clean only with permitted materials!
Clean soiled contacts using oil-free compressed air or with ethyl alcohol and
leather cloths.
Pos: 17.1 1. 4 / Al l e S er ie n ( All g em ei ne D o ku ment e) (All g em ei ne M o dul e) / Wich ti g e E rl ä uter u ng en /Sic h erh ei ts hi nw eis e /Ac ht u ng /Ac ht u ng : K ei n K o nt akts pr a y verwe nd e n! @ 6\mod_1260181290808_21.docx@ 46755@ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos: 17.1 1. 5 / Al l e S er ie n ( All g em ei ne D o ku ment e) (All g em ei ne M o dul e) / Wich ti g e E rl ä uter u ng en /Sic h erh ei ts hi nw eis e /Ac ht u ng /Ac ht u ng : V erp ol ung ver mei de n! @ 6\mod_1260184045744_21.docx @ 46767@ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos: 17.1 1.6 / All e S erie n (Al lge mei ne D o kume nte) (Allg em ein e M odul e)/ Wic ht ig e Er lä uter u ng en /Sic h erh ei ts hin wei se /Ac ht u ng/A c htu ng : El e ktr ost atis c he Entl adu ng ver mei de n! @ 6\mod_1260181364729_21.docx@ 46759 @ @ 1
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
Pos: 18 / D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx @ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Device Description 13
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
Pos: 19 /A lle Ser ien (Al lge meine Mo dule)/ Über schrif ten für all e Serie n/Gerä teb eschrei bung /Gerä tebes chrei bung - Üb er sc hr ift 1 @ 3\mod_1233756084656_21.docx@ 27096@ 1 @ 1
3 Device Description
Pos:20.1/Serie750(WAGO-I/O-S YST EM) /Ger äte b esc hrei bu ng/E i nlei tu ng/A n wen dung /D O/A n wen dung 750-x5 xx D O @ 3\mod_1233764594468_21.docx@ 27120@ @ 1
The 750-531 (4DO 24V DC 0.5A/ 2-conductor) Digital Output Module transmits
binary control signals from the automation device to the connected actuators (e.g.,
solenoid valves, contactors, transmitters, relays or other electrical loads).
Pos:20.2/Serie750(WAGO-I/O-S YST EM) /Ger äte b esc hrei bu ng/E i nlei tu ng/I /O-B es c hrei bu ng /DO / I/ O-B esc hrei bu ng 750-0 5xx 4 D O 2-Leiter(DO und0 V) @ 5\mod_1246611623218_21.docx@ 36565@ @ 1
The module has four output channels. Four 2-conductor actuators may be directly
connected to the module.
The actuators can be connected using connection DO 1 or DO 2, DO 3, DO 4 and
0 V.
Pos:20.3/Serie750(WAGO-I/O-S YST EM) /Ger äte b esc hrei bu ng/E i nlei tu ng/I /O-B es c hr ei bu ng / Al lg em ei n/V er wei s auf K a pi tel "A nsc hl üs s e" @ 8\mod_1276775378035_21.docx@ 57956 @ @ 1
The assignment of the connections is described in the “Connectors” section.
Pos:20.4/Serie750(WAGO-I/O-S YST EM) /Ger äte b esc hrei bu ng/E i nlei tu ng/I /O-B es c hr ei bu ng / Al lg em ei n/V er wei s auf K a pi tel "G er ät e a ns chl i eß en" > "A nsc hlus s bei s piel (e) " @ 5\mod_1246015203281_21.docx@ 36298@ @ 1
Connection examples are shown in section “Connecting Devices” > … >
“Connection Example(s)”.
Pos:20.5/Serie750(WAGO-I/O-SYST EM) / Wic hti g e Er lä ut er ung e n/ Sich er hei ts hin w eis e/H in wei sH i nwei s : D O P ot e ntial v er viel fäl tig u ng s mod ule für A kt or ver sorg u ng eins etz e n @ 3 \mod_1233765481250_21.docx@ 27140 @ @ 1
Use field side connection modules!
Where required, use the appropriate field side connection modules for power
supply to the actuators.
Pos:20.6/Serie750(WAGO-I/O-S YST EM )/ Wi c hti g e Er lä ut er u ng en/ Si ch er h eits - und sonstigeHinweise/AchtungAchtung:DOI nduktionsspannungsbegrenzungElektronik @ 3\mod_1233815757507_21.docx@ 27153@ @ 1
Limit all induced voltage!
The electronic components of the I/O module can be damaged by the induced
voltage produced when inductive loads are de-activated.
An appropriate protection circuit, e.g., a recovery diode, must be installed in
parallel to the load to limit this induced voltage.
Pos:20.7/Serie750(WAGO-I/O-SYST EM) / Ger ät eb esc hrei bu ng /Ei nlei tu ng/ I/O -Bes c hrei bu ng /DO /I / O-B esc hr ei bu ng 750-05 xxDO kurzsc hlussfest @ 3\mod_1233817429086_21.docx@ 27167@ @ 1
The output channels are electrically short-circuit-protected.
Pos:20.8/Serie750(WAGO-I/O-S YST EM ) / Ger äte b esc hr ei bu ng /Ei nlei tu ng/I/ O-B esc hr ei bu ng /D O /I/ O-B es c hr ei bu ng 750-x5 xx D O H SS / pos i ti vsc halt end (24 V) @ 3\mod_1233816955742_21.docx@ 27160@ @ 1
The I/O module outputs provide high-side switching. If the signal status of an
output channel is at “high” the 24 V potential for field power will be switched to
the appropriate output connection.
Pos:20.9/Serie750(WAGO-I/O-S YST EM) /Ger äte b esc hrei bu ng/E i nlei tu ng/I /O-B es c hrei bu ng /DO / I/ O-B esc hrei bu ng 750-05xx LeistungskontaktdurchEinspeiseklemme@ 5\mod_1246856959993_21.docx @ 3659 0 @ @ 1
The supply voltage for the field side is derived from an adjacent supply module by
means of power jumper contacts.
Pos: 20.1 0 / S er ie 750 ( W AG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en /Sic her hei ts- un d s o nsti ge Hin wei se /Ac ht u ngAc ht ung : D O Ü b erl asts c hutz - Ei np eis e klem m e mit Sic her u ng @ 3\mod_1233814881117_21.docx@ 27150@ @ 1
Provide for overload protection!
Overloading can damage the electronic components of the I/O module.
A fused supply module (750-601) must be installed upstream of the I/O module to
protect it against overloading!
Pos: 20.1 1 / S er ie 750 ( W AG O-I/ O-SYST EM) /G er ät e be schr eib u ng /Ei nlei t ung / L ED-A nz eig e/L ED Zus ta nd Sign al @ 3\mod_1233755258578_21.docx@ 27087@ @ 1
A green LED indicates the switched status of each channel.
Pos: 20.1 2 / S er ie 750 ( W AG O-I/ O-SYST EM) /G er ät e be schr eib u ng /Ei nlei t ung / L ED-A nz eig e/V er weis auf Kapi tel "A nzei g eel e me nt e" @ 5\mod_1246010525000_21.docx @ 36194@ @ 1
The meaning of the LEDs is described in the “Display Elements” section.
Pos: 20.1 3 / S er ie 750 ( W AG O-I/ O-SYST EM) /G er ät e be schr eib u ng /Ei nlei t ung / V ers org u ng /V ers org ung 24 V , 0 V ü b er Leist u ng s kont a kt e S t and ar d @ 3\mod _1226498974531_21.docx @ 25020@ @ 1

14 Device Description WAGO-I/O-SYSTEM 750
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
The I/O module 750-531 (4DO 24V DC 0.5A/ 2-conductor) receives the 24 V
voltage supply for the field level from an upstream I/O module or from the
fieldbus coupler/controller via blade-formed power jumper contacts. It then
provides these potentials to subsequent I/O modules via spring-formed power
jumper contacts.
Pos: 20.1 4 / S er ie 750 ( W AG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en /Sic her hei ts- un d s o nsti ge Hin wei se /Ac ht u ng/Ac ht ung : Maxi m aler StromLeistungskontakte10 A @ 3\mod_1226499143500_21.docx@ 25029 @ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos: 20.1 5 / S er ie 750 ( W AG O-I/ O-SYST EM) /G er ät e be schr eib u ng /Ei nlei t ung / V ers org u ng /G al v anis c h e T re n nu ng F eld /S ys te m @ 3\mod_1233756478750_21.docx@ 27102@ @ 1
The field voltage and the system voltage are electrically isolated from each other.
Pos: 20.1 6 / S er ie 750 ( W AG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en /Sic her hei ts- un d s o nsti ge Hin w eise /W ar nu ngW ar n ung : Ei ns atz Var ia nt e / xx x-8xx in s ic h erh ei tsg er icht et e n Anwen d ung en @ 5\mod_1246882860453_21.docx@ 36680@ @ 1
Using in safety related applications!
When using the I/O module ( 750-531 ) in safety-related applications, the
instructions and connection examples in Section “Using Interference-Free
Variants of I/O Modules in Safety Related Applications” are to be observed!
Pos: 20.1 7 /S eri e 7 50 (W AG O-I/ O-SYST E M) /G er ät ebe s chr ei b u ng/ Ei nl eit ung / V er sor gu ng /A n or dnu ng bei Eins a tz in sic her heit s g eri ch te te n Anwe nd ung en bloc kw eis e @ 5\mod_1246876694406_21.docx@ 36674 @ @ 1
Any configuration of the output modules is possible when designing the fieldbus
node. Grouping of module types is not necessary.
Pos: 20.1 8 / S er ie 750 ( W AG O-I/ O-SYST EM) /G er ät e be schr eib u ng /Ei nlei t ung / Ein s at zb erei c h/ Ei n sa tzb er eic h 750-xx xx alle K op pler /C ontr oll er ohne Eins c hrä nk ung @ 3\mod_1232541691906_21.docx @ 26522@ @ 1
The I/O module 750-531 can be used with all fieldbus couplers/controllers of the
WAGO-I/O-SYSTEM 750.
Pos: 21 / D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx @ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
Pos: 22 /Al l e Ser i en ( All g e mei n e M o dul e) /Ü b er schr i f te n f ür all e S er ie n/G er ä te b esc hr eib u ng /A nsi c ht - Ü b er sc hri f t 2@ 4\mod_1240984217343_21.docx@ 31958 @ 2@ 1
3.1 View
Pos: 23 / S eri e 750 ( WA GO-I/ O-SYST EM ) / Ger ät eb es c hrei bu ng /A nsi c ht /D ig it ala usg a ng s kl em me n/ Ansi c ht 75 0-053 1 - Abb. @ 1 0\mod_1298370507089_21.docx@ 69791@ @ 1
Figure 1: View
Pos: 24 / S eri e 750 ( WA GO-I/ O-SYST E M) / Ger ät eb esc hrei bu ng /A nsi c ht /A ns ic ht C ag eC l a mp® _ Leg en de mitLEDs@ 15\mod_1370867188922_21.docx@ 122225@ @ 1
Table 4: Legend for Figure “View”
Pos.
Description
Details See Section
1
Marking possibility with Mini-
WSB
---
2
Status LEDs
“Device Description” > “Display Elements”
3
Data contacts
“Device Description” > “Connectors”
4
CAGE CLAMP®connectors
“Device Description” > “Connectors”
5
Power jumper contacts
“Device Description” > “Connectors”
6
Release tab
“Mounting” > “Inserting and Removing
Devices”
Pos: 25 /D oku ment ation all g emei n/ Gli e der ung s el e me nte /---Sei t e n wechs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

16 Device Description WAGO-I/O-SYSTEM 750
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
Pos: 26 /A lle Ser ien (Al lge meine Mo dule)/ Über schrif ten für all e Serie n/Gerä teb eschrei bung /Ansc hlüss e -Ü ber sc hr ift 2 @ 4\mod_1240984262656_21.docx@ 31961@ 2 @ 1
3.2 Connectors
Pos: 27 / S eri e 750 ( WA GO-I/ O-SYST EM ) / Ger ät eb es c hrei bu ng /A nsc hl üss e/ Da te n ko nta kt e/K l e mme n bu s - Ü ber sc hri ft 3 @ 6\mod_1256294684083_21.docx@ 43660@ 3 @ 1
3.2.1 Data Contacts/Internal Bus
Pos:28.1/Serie750(WAGO-I/O-S YST EM ) / Ger äte b esc hr ei bu ng /A nschlüsse/Datenkontakte- F eld bu s kop pler /-c on tr oll er, A b bi ld ung u nd B es c hr ei bu ng @ 3 \mod_1231771259187_21.docx@ 26002@ @1
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the internal bus. It
is comprised of 6 data contacts, which are available as self-cleaning gold spring
contacts.
Figure 2: Data Contacts
Pos:28.2/Serie750(WAGO-I/O-S YST EM )/ Wi c hti g e Er lä ut er u ng en/ Si ch er h eits - und sons tig e Hi n wei s e/ Ac ht ung /A c ht ung : Buskl e m men nic ht auf G ol df e der kon ta k t e l eg en! @ 7 \mod_1266318463636_21.docx@ 50695 @ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos:28.3/Serie750(WAGO-I/O-S YST EM )/ Wi c hti g e Er lä ut er u ng en/ Si ch er h eits - u nd so nstig e Hinweise/Achtung/Achtung:ESD- A uf g ut e E rd ung der Umg eb ung acht e n! @ 7\mod_1266318538667_21.docx@ 50708@ @ 1
Ensure that the environment is well grounded!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, ensure that the environment
(persons, workplace and packing) is well grounded. Avoid touching conductive
components, e.g. data contacts.
Pos: 29 / D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\ mod_1221108045078_0.docx@ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
Pos: 30 / S eri e 750 ( WA GO-I/ O-SYST EM ) / Ger ät eb es c hrei bu ng /A nsc hl üss e/ Lei st u ng s kont a kt e/F el d vers or gu ng - Über sc hr ift 3 @ 6\mod_1256294692864_21.docx@ 43664@ 3 @ 1
3.2.2 Power Jumper Contacts/Field Supply
Pos: 31 .1 /S erie 750(WAGO-I/O-SYST EM )/ Wi c hti ge Erlä ut er u nge n/ Si ch er h eits - u nd so nst ig e H in wei s e/ Vors ic ht/ V ors ich t: Verl etz ung sg e fahr durc h s ch ar f kan tig e M es s er kont a kte! @ 6\mod_1256193279401_21.docx @ 43414@ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
Pos:31.2/Serie750(WAGO-I/O-S YST EM) / Ger äte b esc hr ei bung /A nsc hl üs se /L eist u ng s kont akt e 2 LK ( M ess er/ Lei s tu ngs k onta kt e 2 LK ( Me ss er /Fe d er) - Einl eit ung @ 15\mod_1371721641099_21.docx@ 123714@ @ 1
The I/O module 750-531 has 2 self-cleaning power jumper contacts that supply
and transmit power for the field side. The contacts on the left side of the I/O
module are designed as blade contacts and those on the right side as spring
contacts.
Pos:31.3/Serie750(WAGO-I/O-S YST EM) / Ger äte b esc hr ei bung /A nsc hl üs se /L eist u ng s kont akt e 2 LK ( M ess er/ Lei s tu ngs k onta kt e 2 LK ( Me ss er /Fe d er) - Abbil dung , ein fac h e Breit e - St an d ard @ 15 \mod_1367500700037_21.docx@ 118396@ @ 1
Figure 3: Power Jumper Contacts
Pos:31.4/Serie750(WAGO-I/O-S YST EM) / Ger äte b esc hr ei bung /A nsc hl üs se /L eist u ng s kont akt e 2 LK ( M ess er/ Lei s tu ngs k onta kt e 2 LK ( Me ss er /Fe d er) - Legende @ 15\mod_1371721352500_21.docx@ 123710@ @ 1
Table 5: Legend for Figure “Power Jumper Contacts”
Contact
Type
Function
1
Spring contact
Potential transmission (Uv) for field supply
2
Spring contact
Potential transmission (0 V) for field supply
3
Blade contact
Potential feed-in (0 V) for field supply
4
Blade contact
Potential feed-in (Uv) for field supply
Pos:31.5/Serie750(WAGO-I/O-S YST EM )/ Wi c hti g e Er lä ut er u ng en/ Si ch er h eits - und sonstige Hinweise/Achtung/Achtung:M aximalerS t ro m L ei st ung s k ont ak t e 10 A @ 3\mod_1226499143500_21.docx@ 25029@ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos:31.6/Serie750(WAGO-I/O-S YST EM )/ Wi c hti g e Er lä ut er u ng en/ Si ch er h eits - u nd s ons tig e H in wei s e/Hin wei s/H i nw eis: Pote nti alei ns pei s ekl emm e für Erd e ei ns etz en! (kei ne LK für Erd e) @ 3\mod_1226499037468_21.docx@ 25023 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
Use supply modules for ground (earth)!
The I/O module has no power jumper contacts for receiving and transmitting the
earth potential. Use a supply module when an earth potential is needed for the
subsequent I/O modules.
Pos: 32 / D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx @ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
Pos: 33 / S eri e 750 ( WA GO-I/ O-SYST E M) / Ger ät eb esc hrei bu ng /A nsc hl üss e/C A GE CLAM P-An schl üs s e - Ü b er sc hri f t 3@ 6\mod_1256296337770_21.doc x@ 436 74 @ 3 @ 1
3.2.3 CAGE CLAMP®Connectors
Pos: 34 / S eri e 750 ( WA GO-I/ O-SYST EM )/ Ger ät eb esc hrei bu ng/ Ans c hl üss e/D ig it al ausg ang s kl e mme n/ Ans chl üss e 750-05 31, 0532 C C @ 10\mod_1298374574196_21.docx@ 69891 @ @ 1
Figure 4: CAGE CLAMP®Connectors
Table 6: Legend for Figure „CAGE CLAMP®Connectors“
Channel
Designation
Connector
Function
1
DO 1 1 Output DO 1: Signal voltage
0V 2 Output DO 1: Field supply 0 V
2
DO 2 5 Output DO 2: Signal voltage
0V 6 Output DO 2: Field supply 0 V
3
0 V 3 Output DO 3: Field supply 0 V
DO 3 4 Output DO 3: Signal voltage
4
0 V 7 Output DO 4: Field supply 0 V
DO 4 8 Output DO 4: Signal voltage
Pos: 35 / D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx @ 21810@ @ 1

20 Device Description WAGO-I/O-SYSTEM 750
750-531 4DO 24V DC 0.5A/ 2-conductor
Manual
Version 1.3.0
Pos: 36 /Al l e Ser i en ( All ge mei ne M od ule) /Ü b ersc hri fte n f ür alle Seri e n/G er ä te b esc hr ei b u ng/ A nz ei geel e m ent e - Ü b ersc hr if t 2 @ 4\mod_1240984390875_21.docx@31964 @ 2@ 1
3.3 Display Elements
Pos: 37 / S eri e 750 ( WA GO-I/ O-SYSTEM)/Gerätebeschreibung/Anzeigeelemente/Digitalausgangsklemmen/Anzeigeelemente750-05xx4DO@ 11\mod_1322035869631_21.docx@ 83554@ @ 1
Figure 5: Display Elements
Table 7: Legend for Figure “Display Elements”
Channel
Designation
LED
State
Function
1 Status DO 1 A
Off
Output DO 1: Signal voltage “0”
Green
Output DO 1: Signal voltage “1”
2 Status DO 2 C
Off
Output DO 2: Signal voltage “0”
Green
Output DO 2: Signal voltage “1”
3 Status DO 3 B
Off
Output DO 3: Signal voltage “0”
Green
Output DO 3: Signal voltage “1”
4 Status DO 4 D
Off
Output DO 4: Signal voltage “0”
Green
Output DO 4: Signal voltage “1”
Pos: 38 /Al l e Ser i en ( All ge mei ne M od ule) /Ü b ersc hri fte n f ür alle Seri en/G er äte b esc hrei bu ng/ Be die nel eme nt e - Ü b ers chr if t 2 @ 4\mod_1239191655456_21.docx@ 30439@ 2 @ 1
3.4 Operating Elements
Pos: 39 / S eri e 750 ( WA GO-I/ O-SYST EM )/ Ger ät ebes c hrei bu ng/B e die nel em ente/ B edi enel em ent e Buskl em me 7 50-x xxx ni c ht vor han de n @ 4\mod_1236322031125_21.docx@ 28063@ @ 1
The I/O module 750-531 has no operating elements.
Pos:40/Dokumentation allg e mei n/ Gl ie der ung s ele m e nte /---Seit e n we chs el --- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1