WAGO 750-482/000-001 User manual

Manual
WAGO I/O System 750
750-482/000-001
2AI 4
-20mA HART NAMUR NE43
2
-Channel Analog Input; 4 mA … 20 mA HART;
NAMUR NE43
Version 1.0.2

2 WAGO I/O System 750
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
© 2020 WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]
Web: www.wago.com
Technical Support
Phone: [phone] – 4 45 55
Fax: [phone] – 84 45 55
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [email protected]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.

WAGO I/O System 750 Table of Contents 3
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
Table of Contents
1Notes about this Documentation .............................................................5
1.1 Validity of this Documentation.................................................................5
1.2 Copyright................................................................................................5
1.3 Symbols .................................................................................................6
1.4 Number Notation ....................................................................................8
1.5 Font Conventions ...................................................................................8
2Important Notes ........................................................................................9
2.1 Legal Bases............................................................................................9
2.1.1 Subject to Changes............................................................................9
2.1.2 Personnel Qualifications ....................................................................9
2.1.3 Use of the 750 Series in Compliance with Underlying Provisions.......9
2.1.4 Technical Condition of Specified Devices.........................................10
2.1.4.1 Disposal ......................................................................................10
2.1.4.1.1 Electrical and Electronic Equipment........................................10
2.1.4.1.2 Packaging...............................................................................11
2.2 Safety Advice (Precautions) .................................................................12
3Device Description..................................................................................15
3.1 View .....................................................................................................18
3.2 Connectors...........................................................................................19
3.2.1 Data Contacts/Local Bus..................................................................19
3.2.2 Power Jumper Contacts/Field Supply ..............................................20
3.2.3 CAGE CLAMP®Connectors.............................................................21
3.3 Display Elements..................................................................................22
3.4 Operating Elements..............................................................................22
3.5 Schematic Diagram ..............................................................................23
3.6 Technical Data .....................................................................................24
3.6.1Device Data .....................................................................................24
3.6.2 Supply..............................................................................................24
3.6.3 Communication................................................................................24
3.6.4 Inputs...............................................................................................24
3.6.5 Connection Type..............................................................................25
3.6.6 Climatic Environmental Conditions...................................................26
3.7 Approvals .............................................................................................27
3.8 Standards and Guidelines ....................................................................28
4Process Image.........................................................................................29
4.1 6 Byte Mailbox......................................................................................30
4.2 1 HART Variable per Channel ..............................................................33
4.3 2 HART Variables per Channel.............................................................34
4.4 3 HART Variables per Channel.............................................................35
4.5 4 HART Variables per Channel.............................................................36
4.6 Acyclic PROFIBUS Services ................................................................37
5Mounting..................................................................................................40
5.1 Mounting Sequence..............................................................................41
5.2 Inserting and Removing Devices ..........................................................41

4 Table of Contents WAGO I/O System 750
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
5.2.1 Inserting the I/O Module...................................................................41
5.2.2 Removing the I/O Module ................................................................43
6Connect Devices .....................................................................................44
6.1 Connecting a Conductor to the CAGE CLAMP®...................................44
6.2 Power Supply Concept .........................................................................45
6.3 Connection Example ............................................................................46
7Function Description ..............................................................................47
8Operating Modes.....................................................................................49
8.1 Setting the Operating Mode Parameters...............................................50
8.1.1 Setting Up using WAGO-I/O-CHECK ...............................................51
8.1.2 Settings via GSD..............................................................................53
8.2 FDT/DTM Concept ...............................................................................56
8.3 HART on PROFIBUS ...........................................................................58
9Commissioning .......................................................................................59
9.1 With PLC Library on All Compatible 75x-xxx Fieldbus
Couplers/Controllers.............................................................................59
9.1.1 Communication on 75x-xxx via PLC Library.....................................60
9.1.2 Startup on the 75x-xxx via PLC Library ............................................61
9.2 With HART Dynamic Variables on PROFIBUS DP/V1 750-333 and
750-833 ................................................................................................62
9.2.1 Communication on the 750-333, -833 with Dynamic Variables.........64
9.2.2 Commissioning on the 750-333, -833 with Dynamic Variables .........64
9.3 FDT/DTM with the PROFIBUS DP/V1 750-333, 750-833 .....................66
9.3.1 Communication on 750-333, -833 via FDT/DTM ..............................67
9.3.2 Commissioning on a 750-333, -833 via FDT/DTM............................68
10 Use in Hazardous Environments ...........................................................76
10.1 Marking Configuration Examples ..........................................................77
10.1.1 Marking for Europe According to ATEX and IECEx..........................77
10.1.2 Marking for the United States of America (NEC) and Canada
(CEC)...............................................................................................81
10.2 Installation Regulations.........................................................................84
10.2.1 Special Notes including Explosion Protection...................................84
10.2.2Special Notes Regarding UL Hazardous Location............................86
11 Appendix .................................................................................................87
11.1 Information for Hart Library...................................................................87
11.1.1 CODESYS Library ...........................................................................87
11.1.2 PROFIBUS Gateway........................................................................87
List of Figures ..................................................................................................88
List of Tables....................................................................................................89

WAGO I/O System 750 Notes about this Documentation 5
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
1 Notes about this Documentation
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation
is included, if necessary.
1.1 Validity of this Documentation
This documentation is only applicable to the I/O module 750-482/000-001
(2AI 4-20mA HART NAMUR NE43).
The I/O module 750-482/000-001 shall only be installed and operated according
to the instructions in this manual and in the manual for the used fieldbus coupler
or controller.
Consider power layout of the WAGO I/O System 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler or controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
1.2 Copyright
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.

6 Notes about this Documentation WAGO I/O System 750
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
1.3 Symbols
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.

WAGO I/O System 750 Notes about this Documentation 7
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).

8 Notes about this Documentation WAGO I/O System 750
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
1.4 Number Notation
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated
with dots (.)
1.5 Font Conventions
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.: Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under
Start of measurement range
.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]

WAGO I/O System 750 Important Notes 9
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
2 Important Notes
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
2.1 Legal Bases
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all
rights arising from the granting of patents or from the legal protection of utility
patents. Third-party products are always mentioned without any reference to
patent rights. Thus, the existence of such rights cannot be excluded.
2.1.2 Personnel Qualifications
All sequences implemented on WAGO I/O System 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
2.1.3 Use of the 750 Series in Compliance with Underlying
Provisions
Fieldbus couplers, controllers and I/O modules found in the modular WAGO I/O
System 750 receive digital and analog signals from sensors and transmit them to
actuators or higher-level control systems. Using controllers, the signals can also
be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO I/O System 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information in
the section “Device Description” > “Standards and Guidelines” in the manual for
the used device.
Appropriate housing (per 2014/34/EU) is required when operating the WAGO I/O
System 750 in hazardous environments. Please observe the installation

10 Important Notes WAGO I/O System 750
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
regulations! Please note that a prototype test certificate must be obtained that
confirms the correct installation of the system in a housing or switch cabinet.
The implementation of safety functions such as EMERGENCY STOP or safety
door monitoring must only be performed by the F I/O modules within the modular
WAGO I/O System 750. Only these safe F I/O modules ensure functional safety
in accordance with the latest international standards. WAGO's interference-free
output modules can be controlled by the safety function.
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. These
modules contain no parts that can be serviced or repaired by the user. The
following actions will result in the exclusion of liability on the part of WAGO
Kontakttechnik GmbH & Co. KG:
• Repairs,
• Changes to the hardware or software that are not described in the
operating instructions,
• Improper use of the components.
Further details are given in the contractual agreements. Please send your
request for modified and new hardware or software configurations directly to
WAGO Kontakttechnik GmbH & Co. KG.
2.1.4.1 Disposal
2.1.4.1.1 Electrical and Electronic Equipment
Electrical and electronic equipment may not be disposed of
with household waste. This also applies to products without
this symbol.
Electrical and electronic equipment contain materials and substances that can be
harmful to the environment and health. Electrical and electronic equipment must
be disposed of properly after use.
WEEE 2012/19/EU applies throughout Europe. Directives and laws may vary
nationally.
Environmentally friendly disposal benefits health and protects
the environment from harmful substances in electrical and
electronic equipment.

WAGO I/O System 750 Important Notes 11
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
• Observe national and local regulations for the disposal of electrical and
electronic equipment.
• Clear any data stored on the electrical and electronic equipment.
• Remove any added battery or memory card in the electrical and
electronic equipment.
• Have the electrical and electronic equipment sent to your local
collection point.
Improper disposal of electrical and electronic equipment can be harmful to the
environment and human health.
2.1.4.1.2 Packaging
Packaging contains materials that can be reused.
PPWD 94/62/EU and 2004/12/EU packaging guidelines apply throughout
Europe. Directives and laws may vary nationally.
Environmentally friendly disposal of the packaging protects the environment and
allows sustainable and efficient use of resources.
• Observe national and local regulations for the disposal of packaging.
• Dispose of packaging of all types that allows a high level of recovery,
reuse and recycling.
Improper disposal of packaging can be harmful to the environment and wastes
valuable resources.

12 Important Notes WAGO I/O System 750
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
2.2 Safety Advice (Precautions)
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Install device in only one suitable enclosure!
The device is an open system. Install the device in a suitable enclosure. This
enclosure must:
• Guarantee that the max. permissible degree of pollution is not exceeded.
• Offer adequate protection against contact.
• Prevent fire from spreading outside of the enclosure.
• Offer adequate protection against UV irradiation.
• Guarantee mechanical stability
• Restrict access to authorized personnel and may only be opened with tools
Ensure disconnect and overcurrent protection!
The device is intended for installation in automation technology systems.
Disconnect protection is not integrated. Connected systems must be protected by
a fuse.
Provide suitable disconnect and overcurrent protection on the system side!
Ensure a standard connection!
To minimize any hazardous situations resulting in personal injury or to avoid
failures in your system, the data and power supply lines shall be installed
according to standards, with careful attention given to ensuring the correct
terminal assignment. Always adhere to the EMC directives applicable to your
application.

WAGO I/O System 750 Important Notes 13
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
Power from SELV/PELV power supply only!
All field signals and field supplies connected to this I/O module (750-482/000-
001) must be powered from SELV/PELV power supply(s)!
Ensuring Immunity to Interference
Place a field-side power supply filter (surge) (750-624/020-001) before the HART
I/O module to ensure immunity to interference!
Ensure proper contact with the DIN-rail!
Proper electrical contact between the DIN-rail and device is necessary to
maintain the EMC characteristics and function of the device.
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts).
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for
handling devices/modules.
Clean only with permitted materials!
Clean housing and soiled contacts with propanol.
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.

14 Important Notes WAGO I/O System 750
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.

WAGO I/O System 750 Device Description 15
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
3 Device Description
The Analog Input Module 750-482/000-001 (2AI 4-20mA HART NAMUR NE43)
processes analog signals with the norm value of 4 mA ... 20 mA.
The I/O module also enables digital communication to be carried out with HART-
enabled field devices (Highway Addressable Remote Transducer).
The I/O module has 2 input channels and enables field signals to be received via
the +HART 1 and −HART 1 and +HART 2 and −HART 2 connections. Typically,
the current values are measured at these connections, but at the same time the
HART signals can also be coupled and decoupled.
The channels have a common reference potential and a shield connection.
The shield connection is fed directly to the carrier rail and contact is made
automatically by snapping the module onto the rail.
The channels are not electrically isolated from one another.
Dabei
Two-conductor transducers, which do not have their own power supply, such as
adjustable resistances, pressure, flow and level meters, can be connected
directly.
The transducers are directly supplied from the I/O module.
In order to connect the 0 V line when using 3-conductor transducers, a 75x-604
or –614 Field Side Connection Module must be plugged in next to the HART I/O
module, providing the 0 V potential for the field level.
The input signal is electrically isolated and is transmitted with a resolution of
12 bits.
Simple parameterization of the HART I/O module for 6 different operating modes
enables the I/O module to be used optimally for 3 different types of application.
Table 3: Types of Application
Types of Application for the HART I/O Module
1
Programmable fieldbus controllers can communicate with HART devices
from IEC61131-3 programs using the “WagoLibHART_0x.lib” PLC library.
2
Up to 4 HART dynamic variables (PV, SV, TV, QV) can be incorporated in
the cyclic process image of the 750-333 PROFIBUS Coupler or 750-833
PROFIBUS Controller by parameterization via GSD (device master data) or
WAGO-I/O-CHECK.
3
When using the 750-333 PROFIBUS DP/V1 Coupler or 750-833
PROFIBUS Controller and the 759-360 PROFIBUS/HART Gateway DTM,
FDT tool routing is possible to the DTM of the connected HART device.
The operating status of the channels is indicated by a green status LED per
channel.
A red error LED per channel indicates a wire break, a short circuit or that the
signal is outside the measuring range.

16 Device Description WAGO I/O System 750
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
The meaning of the LEDs is described in the “Display Elements” section.
Ensuring Immunity to Interference
Place a field-side power supply filter (surge) (750-624/020-001) before the HART
I/O module to ensure immunity to interference!
The I/O module 750-482/000-001 (2AI 4-20mA HART NAMUR NE43) receives
the 24 V power supply and 0 V potential for the field level from the upstream
field-side power supply filter (surge) (750-624/020-001) via the power jumper
contacts designed as blade contacts. It then provides the potential to subsequent
I/O modules via power jumper contacts designed as spring contacts.
Use supply modules for ground (earth)!
The I/O module has no power jumper contacts for receiving and transmitting the
earth potential. Use a supply module when an earth potential is needed for the
subsequent I/O modules.
Do not exceed maximum values via power contacts!
The maximum current that can flow through the power jumper contacts is 10 A.
The power jumper contacts can be damaged and the permissible operating
temperature can be exceeded by higher current values.
When configuring the system, do not exceed the permissible maximum current
value. If there is a higher power requirement, you must use an additional supply
module to provide the field voltage.
Avoid short circuit
A short circuit between the "HART+" connectors and ground can destroy the
module. Therefore, make sure that no grounded part of the field device housing
comes into contact with the "HART+" connector, for example, during installation.
The HART I/O module can be used with all couplers and controllers of the
WAGO-I/O-SYSTEM 750 listed in the following table “Compatibility List”.

WAGO I/O System 750 Device Description 17
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
Table 4: Compatibility List
Bus System Fieldbus Coupler/
Controller Item No.
Hard-
ware
Version
Soft-
ware
Version
Max. Number
of Modules Function*)
ETHERNET
TCP/IP
Programmable
Fieldbus Controllers
750-841
03
07
8
(1), (5)
750-842
04
12
8
(1), (5)
750-871
01
01
8
(1), (5)
750-872
01
01
8
(1), (5)
750-872/
020-000
01 07 8 (1), (5)
750-873
01
01
8
(1), (5)
750-880
06
03
8
(1), (5)
750-881
06
03
8
(1), (5)
750-882
06
03
8
(1), (5)
750-885
06
03
8
(1), (5)
PFC100
750-8100
xx
from 11
40
(1), (5)
750-8101
xx
from 11
40
(1), (5)
750-8102
xx
from 11
40
(1), (5)
PFC200 750-8202 xx from 01 40 (1), (5)
CANopen
Programmable
Fieldbus Controllers
750-837
07
12
8
(1)
750-838
02
12
8
(1)
PFC200
750-8203
xx
from 01
40
(1), (5)
750-8204
xx
from 01
40
(1), (5)
DeviceNet
Programmable
Fieldbus Controllers
750-806 04 09 8 (1)
LON
Programmable
Fieldbus Controllers
750-819 xx 09 8 (1)
PROFIBUS
Fieldbus Coupler
750-333
12
from 13
8
(2), (3), (4)
Programmable
Fieldbus Controllers
750-833 12 from 10 8
(1), (2), (3),
(4)
PFC200
750-8206
xx
from 01
40
(1), (5)
750-8208
xx
from 01
40
(1), (5)
PROFINET Fieldbus Coupler
750-375
01
03
8
(6)
750-377
01
03
8
(6)
BACnet Programmable
Fieldbus Controllers
750-829
01
07
8
(1)
750-830
01
01
8
(1)
750-831
01
07
8
(1)
KNX
Programmable
Fieldbus Controllers
750-849
xx
from 01
8
(1)
750-889
01
07
8
(1)
Other Fieldbus Coupler/Controller on request.
*)
Functions:
(1)
WAGO-I/O-PRO CAA (CODESYS) PLC library „WagoLibHART_0x.lib“
(2)
Cyclic Profibus communication with HART dynamic variables
(3)
Acyclic Profibus communication with HART Toolrouting FDT/DTM or eddl/SimaticPDM
(4)
PROFIBUS/HART Gateway DTM 759-360
(5)
ModbusTCP/HART Gateway DTM 759-359
(6)
Cyclic Profinet communication with HART dynamic variables

18 Device Description WAGO I/O System 750
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
3.1 View
Figure 1: View
Table 5: Legend for Figure “View”
Pos.
Description
Details See Section
1
Marking possibility with Mini-
WSB
---
2
Status LEDs
“Device Description” > “Display Elements”
3
Data contacts
“Device Description” > “Connectors”
4
CAGE CLAMP®connectors
“Device Description” > “Connectors”
5
Power jumper contacts
“Device Description” > “Connectors”
6
Release tab
“Mounting” > “Inserting and Removing
Devices”

WAGO I/O System 750 Device Description 19
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
3.2 Connectors
3.2.1 Data Contacts/Local Bus
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the local bus. The
contacting for the local bus consists of 6 data contacts, which are available as
self-cleaning gold spring contacts.
Figure 2: Data Contacts
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pay attention to potential equalization from the environment!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, please ensure that
environmental factors (personnel, work space and packaging) are properly
equalized. Do not touch any conducting parts, e.g., data contacts.

20 Device Description WAGO I/O System 750
750-482/000-001 2AI 4-20mA HART NAMUR NE43
Manual
Version 1.0.2
3.2.2 Power Jumper Contacts/Field Supply
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury. Do not touch the blade contacts.
The I/O module 750-482/000-001 has 2 self-cleaning power jumper contacts that
supply and transmit power for the field side. The contacts on the left side of the
I/O module are designed as blade contacts and those on the right side as spring
contacts.
Figure 3: Power Jumper Contacts
Table 6: Legend for Figure “Power Jumper Contacts”
Contact
Type
Function
1
Spring contact
Potential transmission (U
v
) for field supply
2
Spring contact
Potential transmission (0 V) for field supply
3
Blade contact
Potential feed-in (0 V) for field supply
4
Blade contact
Potential feed-in (Uv) for field supply
Do not exceed maximum values via power contacts!
The maximum current that can flow through the power jumper contacts is 10 A.
The power jumper contacts can be damaged and the permissible operating
temperature can be exceeded by higher current values.
When configuring the system, do not exceed the permissible maximum current
value. If there is a higher power requirement, you must use an additional supply
module to provide the field voltage.