WAGO I/O System 750 750-622 User manual

Fieldbus Independent
I/O Modules
Binary Spacer Module
750-622
Manual
Version 1.0.2

ii • General
WAGO-I/O-SYSTEM 750
I/O Modules
Copyright ©2006 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]
Web: http://www.wago.com
Technical Support
Phone: [phone] – 5 55
Fax: [phone] – 85 55
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the correctness and com-
pleteness of this documentation. However, as errors can never be fully ex-
cluded, we would appreciate any information or ideas at any time.
E-Mail: [email protected]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally trademark or patent protected.

Content •iii
WAGO-I/O-SYSTEM 750
I/O Modules
CONTENT
1Important Comments ................................................................................. 4
1.1 Legal Principles........................................................................................4
1.1.1 Copyright............................................................................................. 4
1.1.2 Personnel Qualification .......................................................................4
1.1.3 Intended Use ........................................................................................4
1.2 Symbols....................................................................................................5
1.3 Number Notation......................................................................................5
1.4 Safety Notes .............................................................................................6
1.5 Scope ........................................................................................................6
2I/O Modules ................................................................................................. 7
2.1 System Modules .......................................................................................7
2.1.1 750-622 [Binary Spacer Module]........................................................7
2.1.1.1 View................................................................................................7
2.1.1.2 Description......................................................................................7
2.1.1.3 Display Elements ............................................................................8
2.1.1.4 Schematic Diagram.........................................................................9
2.1.1.5 Technical Data ................................................................................9

4 •Important Comments
Legal Principles
WAGO-I/O-SYSTEM 750
I/O Modules
1 Important Comments
To ensure fast installation and start-up of the units described in this manual,
we strongly recommend that the following information and explanations are
carefully read and abided by.
1.1 Legal Principles
1.1.1 Copyright
This manual is copyrighted, together with all figures and illustrations
contained therein. Any use of this manual which infringes the copyright
provisions stipulated herein, is not permitted. Reproduction, translation and
electronic and photo-technical archiving and amendments require the written
consent of WAGO Kontakttechnik GmbH & Co. KG. Non-observance will
entail the right of claims for damages.
WAGO Kontakttechnik GmbH & Co. KG reserves the right to perform
modifications allowed by technical progress. In case of grant of a patent or
legal protection of utility patents all rights are reserved by WAGO
Kontakttechnik GmbH & Co. KG. Products of other manufacturers are always
named without referring to patent rights. The existence of such rights can
therefore not be ruled out.
1.1.2 Personnel Qualification
The use of the product detailed in this manual is exclusively geared to
specialists having qualifications in PLC programming, electrical specialists or
persons instructed by electrical specialists who are also familiar with the valid
standards. WAGO Kontakttechnik GmbH & Co. KG declines all liability
resulting from improper action and damage to WAGO products and third party
products due to non-observance of the information contained in this manual.
1.1.3 Intended Use
For each individual application, the components supplied are to work with a
dedicated hardware and software configuration. Modifications are only
permitted within the framework of the possibilities documented in the
manuals. All other changes to the hardware and/or software and the non-
conforming use of the components entail the exclusion of liability on part of
WAGO Kontakttechnik GmbH & Co. KG.
Please direct any requirements pertaining to a modified and/or new hardware
or software configuration directly to WAGO Kontakttechnik GmbH & Co.
KG.

Important Comments •5
Symbols
WAGO-I/O-SYSTEM 750
I/O Modules
1.2 Symbols
Danger
Always abide by this information to protect persons from injury.
Warning
Always abide by this information to prevent damage to the device.
Attention
Marginal conditions must always be observed to ensure smooth operation.
ESD (Electrostatic Discharge)
Warning of damage to the components by electrostatic discharge. Observe
the precautionary measure for handling components at risk.
Note
Routines or advice for efficient use of the device and software optimization.
More information
References on additional literature, manuals, data sheets and INTERNET
pages
1.3 Number Notation
Number Code Example Note
Decimal 100 normal notation
Hexadecimal 0x64 C notation
Binary '100'
'0110.0100'
Within ',
Nibble separated with dots

6 •Important Comments
Safety Notes
WAGO-I/O-SYSTEM 750
I/O Modules
1.4 Safety Notes
Warning
Switch off the system prior to working on bus modules!
In the event of deformed contacts, the module in question is to be replaced, as
its functionality can no longer be ensured on a long-term basis.
The components are not resistant against materials having seeping and
insulating properties. Belonging to this group of materials is: e.g. aerosols,
silicones, triglycerides (found in some hand creams).
If it cannot be ruled out that these materials appear in the component
environment, then additional measures are to be taken:
- installation of the components into an appropriate enclosure
- handling of the components only with clean tools and materials.
Attention
Cleaning of soiled contacts may only be done with ethyl alcohol and leather
cloths. Thereby, the ESD information is to be regarded.
Do not use any contact spray. The spray may impair the functioning of the
contact area.
The WAGO-I/O-SYSTEM 750 and its components are an open system. It
must only be assembled in housings, cabinets or in electrical operation
rooms. Access must only be given via a key or tool to authorized qualified
personnel.
The relevant valid and applicable standards and guidelines concerning the
installation of switch boxes are to be observed.
ESD (Electrostatic Discharge)
The modules are equipped with electronic components that may be destroyed
by electrostatic discharge. When handling the modules, ensure that the
environment (persons, workplace and packing) is well grounded. Avoid
touching conductive components, e.g. gold contacts.
1.5 Scope
This manual describes the Digital Input Module 750-622 Binary Spacer
Module of the modular WAGO-I/O-SYSTEM 750.
Handling, assembly and start-up are described in the manual of the Fieldbus
Coupler. Therefore this documentation is valid only in the connection with the
appropriate manual.

750-622 [Binary Spacer Module] •7
View
WAGO-I/O-SYSTEM 750
I/O Modules
2 I/O Modules
2.1 System Modules
2.1.1 750-622 [Binary Spacer Module]
Binary Spacer Module, with power supply
2.1.1.1 View
++
--
13 14
C
D
B
A
750-622
0V
Power jumper contacts
Data width
Supply via power
jumper contacts
24V
Data contacts
Operating mode
Input/
output
Fig. 2.1.1-1: Binary Spacer Module 750-622 g062200e
2.1.1.2 Description
The binary spacer module reserves digital addresses in the WAGO buscoupler.
The number of inputs or outputs can be selected by two DIP switches. 2, 4, 6
or 8 bits are possible (equivalent to 1, 2, 3 or 4 two-channel modules). A third
DIP Switch selects inputs or outputs.
The configuration is indicated by means of 3 LEDs, which are lit, even if there
is no voltage applied.
The binary spacer module also works as a 24 V supply module. Power must be
connected to supply the modules following the binary spacer.
Warning
The maximum current of the binary spacer module is 10 A. When configuring
the system it is important not to exceed the maximum/sum current. However,
if such a case should occur, another supply module must be added.
The binary spacer module 750-622 can be used with all couplers/controllers of
the WAGO-I/O-SYSTEM 750.

8 • 750-622 [Binary Spacer Module]
Display Elements
WAGO-I/O-SYSTEM 750
I/O Modules
Note
The spacer module 750-622 is represented as 1, 2, 3 or 4 two-channel modules
in the process image of couplers / controllers that require the number of
connected modules in order to be addressed.
The DIP switches are used as follows:
Fig. 2.1.1-2: Switch Settings Binary Spacer Module 750-622 g062202e
2.1.1.3 Display Elements
LED Designation State Function
A off
C off 2 bits (1 x 2 bits)
A on
C off 4 bits (2 x 2 bits)
A off
C on 6 bits (3 x 2 bits)
A, C
green data width
A on
C on 8 bits (4 x 2 bits)
off input
Fig. 2.1.1-3: Display
Elements g062203x
B
green
operating
mode on output

750-622 [Binary Spacer Module] •9
Schematic Diagram
WAGO-I/O-SYSTEM 750
I/O Modules
2.1.1.4 Schematic Diagram
Operating
mode
Data width
DIP 5
Logic
DIP 4
DIP 3
DIP 2
DIP 1
0V
24V
1
2
3
4
5
6
7
8
750-622
Fig. 2.1.1-4: Binary Spacer Module 750-622 g062201e
2.1.1.5 Technical Data
Module Specific Data
Number of Inputs/Outputs 2, 4, 6 or 8
Voltage via power jumper contacts DC 24 V (-15% ... +20%)
Current via power jumper contacts max. 10 A
Current consumption (internal) 10 mA
Isolation 500 V (System/Supply)
Internal bit width 2, 4, 6 or 8 Bit
Dimensions (mm) W x H x L 12 x 64* x 100
* from upper edge of 35 DIN rail
Weight ca. 40 g
Standards and Regulations (cf. Chapter 2.2 of the Coupler/Controller Manual)
EMC-Immunity to interference (CE) acc. to EN 50082-2 (1996)
EMC-Emission of interference (CE) acc. to EN 50081-1 (1993)
Approvals (cf. Chapter 2.2 of the Coupler/Controller Manual)
CULUS (UL508)
CULUS (UL1604) Class I Div2 ABCD T4A
KEMA II 3 G EEx nA II T4
Conformity Marking

10 • 750-622 [Binary Spacer Module]
Technical Data
WAGO-I/O-SYSTEM 750
I/O Modules
More Information
Detailed references to the approvals are listed in the document "Overview
Approvals WAGO-I/O-SYSTEM 750", which you can find on the CD ROM
ELECTRONICC Tools and Docs (Item-No.: 0888-0412)
or in the internet under:
www.wago.com !Documentation !WAGO-I/O-SYSTEM 750 !
System Description