WAGO I/O-SYSTEM 750 User manual

Fieldbus Independent
I/O Modules
2 AO 0-10V DC 10Bit 10mA 24V
750-560
Manual
Version 1.0.3

ii • General
WAGO-I/O-SYSTEM 750
I/O Modules
Copyright 2007 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]
Web: http://www.wago.com
Technical Support
Phone: [phone] – 5 55
Fax: [phone] – 85 55
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the correctness and com-
pleteness of this documentation. However, as errors can never be fully ex-
cluded, we would appreciate any information or ideas at any time.
E-Mail: [email protected]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally trademark or patent protected.

Content • iii
WAGO-I/O-SYSTEM 750
I/O Modules
Content
1Important Comments ................................................................................. 4
1.1 Legal Principles........................................................................................4
1.1.1 Copyright ............................................................................................. 4
1.1.2 Personnel Qualification ....................................................................... 4
1.1.3 Intended Use ........................................................................................ 4
1.2 Symbols .................................................................................................... 5
1.3 Number Notation...................................................................................... 5
1.4 Safety Notes ............................................................................................. 6
1.5 Scope ........................................................................................................ 6
2I/O Modules ................................................................................................. 7
2.1 Analog Output Modules ........................................................................... 7
2.1.1 750-560 [2 AO 0-10V DC 10Bit 10mA 24V] ..................................... 7
2.1.1.1 View................................................................................................ 7
2.1.1.2 Description...................................................................................... 7
2.1.1.3 Display Elements ............................................................................ 8
2.1.1.4 Schematic Diagram......................................................................... 9
2.1.1.5 Technical Data .............................................................................. 10
2.1.1.6 Process Image ...............................................................................11
2.1.1.6.1 Standard Format ....................................................................... 11

4 •Important Comments
Legal Principles
WAGO-I/O-SYSTEM 750
I/O Modules
1 Important Comments
To ensure fast installation and start-up of the units described in this manual,
we strongly recommend that the following information and explanations are
carefully read and abided by.
1.1 Legal Principles
1.1.1 Copyright
This manual is copyrighted, together with all figures and illustrations
contained therein. Any use of this manual which infringes the copyright
provisions stipulated herein, is not permitted. Reproduction, translation and
electronic and photo-technical archiving and amendments require the written
consent of WAGO Kontakttechnik GmbH & Co. KG. Non-observance will
entail the right of claims for damages.
WAGO Kontakttechnik GmbH & Co. KG reserves the right to perform
modifications allowed by technical progress. In case of grant of a patent or
legal protection of utility patents all rights are reserved by WAGO
Kontakttechnik GmbH & Co. KG. Products of other manufacturers are always
named without referring to patent rights. The existence of such rights can
therefore not be ruled out.
1.1.2 Personnel Qualification
The use of the product detailed in this manual is exclusively geared to
specialists having qualifications in PLC programming, electrical specialists or
persons instructed by electrical specialists who are also familiar with the valid
standards. WAGO Kontakttechnik GmbH & Co. KG declines all liability
resulting from improper action and damage to WAGO products and third party
products due to non-observance of the information contained in this manual.
1.1.3 Intended Use
For each individual application, the components supplied are to work with a
dedicated hardware and software configuration. Modifications are only
permitted within the framework of the possibilities documented in the
manuals. All other changes to the hardware and/or software and the non-
conforming use of the components entail the exclusion of liability on part of
WAGO Kontakttechnik GmbH & Co. KG.
Please direct any requirements pertaining to a modified and/or new hardware
or software configuration directly to WAGO Kontakttechnik GmbH & Co.
KG.

Important Comments •5
Symbols
WAGO-I/O-SYSTEM 750
I/O Modules
1.2 Symbols
Danger
Always abide by this information to protect persons from injury.
Warning
Always abide by this information to prevent damage to the device.
Attention
Marginal conditions must always be observed to ensure smooth operation.
ESD (Electrostatic Discharge)
Warning of damage to the components by electrostatic discharge. Observe
the precautionary measure for handling components at risk.
Note
Routines or advice for efficient use of the device and software optimization.
More information
References on additional literature, manuals, data sheets and INTERNET
pages
1.3 Number Notation
Number Code Example Note
Decimal 100 normal notation
Hexadecimal 0x64 C notation
Binary '100'
'0110.0100'
Within ',
Nibble separated with dots

6 •Important Comments
Safety Notes
WAGO-I/O-SYSTEM 750
I/O Modules
1.4 Safety Notes
Warning
Switch off the system prior to working on bus modules!
In the event of deformed contacts, the module in question is to be replaced, as
its functionality can no longer be ensured on a long-term basis.
The components are not resistant against materials having seeping and
insulating properties. Belonging to this group of materials is: e.g. aerosols,
silicones, triglycerides (found in some hand creams).
If it cannot be ruled out that these materials appear in the component
environment, then additional measures are to be taken:
- installation of the components into an appropriate enclosure
- handling of the components only with clean tools and materials.
Attention
Cleaning of soiled contacts may only be done with ethyl alcohol and leather
cloths. Thereby, the ESD information is to be regarded.
Do not use any contact spray. The spray may impair the functioning of the
contact area.
The WAGO-I/O-SYSTEM 750 and its components are an open system. It
must only be assembled in housings, cabinets or in electrical operation
rooms. Access must only be given via a key or tool to authorized qualified
personnel.
The relevant valid and applicable standards and guidelines concerning the
installation of switch boxes are to be observed.
ESD (Electrostatic Discharge)
The modules are equipped with electronic components that may be destroyed
by electrostatic discharge. When handling the modules, ensure that the
environment (persons, workplace and packing) is well grounded. Avoid
touching conductive components, e.g. gold contacts.
1.5 Scope
This manual describes the Analog Output Module 750-560
2 AO 0-10V DC 10Bit 10mA 24V of the modular WAGO-I/O-SYSTEM 750.
Handling, assembly and start-up are described in the manual of the Fieldbus
Coupler. Therefore this documentation is valid only in the connection with the
appropriate manual.

750-560 [2 AO 0-10V DC 10Bit 10mA 24V] • 7
View
WAGO-I/O-SYSTEM 750
I/O Modules
2 I/O Modules
2.1 Analog Output Modules
2.1.1 750-560 [2 AO 0-10V DC 10Bit 10mA 24V]
2-Channel Analog Output Module 0-10 V, 10 Bit, 10 mA
2.1.1.1 View
A1 A2
SS
13 14
C
D
B
A
750-560
MM
AO 2
Power jumper
contacts
Data contacts
24 V AC/DC
Function AO 1
AO 1
0V
Shield
(screen)
Function AO 2
Error AO 1 Error AO 2
Shield
(screen)
Fig. 2.1.1-1: 2- Channel Analog Output Module 750-560 g056000e
2.1.1.2 Description
The analog output module 750-560 creates a standardized signal of 0-10 V.
The module has two short circuit protected output channels and enables, for
example, the direct wiring of two 3-conductor actuators to the connections
AO 1, AC/DC 24 V and 0 V or AO 2, AC/DC 24 V and 0 V. The signals are
transmitted via AO 1 and AO 2.
The channels have a common ground and a common shield (screen) (S). The
shield (screen) is directly connected to the DIN rail. A capacitive connection
is made automatically when snapped onto the DIN rail.
The input signal is electrically isolated and will be transmitted with a
resolution of 10 bits.
The operational readiness and the trouble-free internal data bus
communication of the channels are indicated via a green function LED.
In addition, a red error LED will show if there are any overload ≥15 mA or a
short circuit to ground in either channel.

8 •750-560 [2 AO 0-10V DC 10Bit 10mA 24V]
Display Elements
WAGO-I/O-SYSTEM 750
I/O Modules
Any configuration of the output modules is possible when designing the
fieldbus node. Grouping of module types is not necessary.
The system supply and the field side supply voltage is used for the power
supply of the module.
The field side supply voltage of 0 V and 24 V to downstream I/O modules is
derived from adjacent I/O modules or from a supply module.The supply
voltage for the field side is made automatically through the individual I/O
modules by means of power jumper contacts.
Warning
The maximum current of the internal power jumper contacts is 10 A. When
configuring the system it is important not to exceed the maximum/sum
current. However, if such a case should occur, another supply module must be
added.
The analog output module 750-560 can be used with all couplers/controllers
of the WAGO-I/O-SYSTEM 750 (except for the economy types 750-320, -
323, -324 and -327).
2.1.1.3 Display Elements
LED Channel Designation State Function
off
No operational readiness or the
internal data bus
communication is interrupted
A
green
Function
AO 1
on
Operational readiness and
trouble-free internal data bus
communication
off Normal operation
B
red
1
Error
AO 1 on Short circuit to ground or
overload ≥15 mA
off
No operational readiness or the
internal data bus
communication is interrupted
C
green
Function
AO 2
on
Operational readiness and
trouble-free internal data bus
communication
off Normal operation
13 14
C
D
B
A
D
C
B
A
Fig. 2.1.1-2: Display
elements g056002x
D
red
2
Error
AO 2 on Short circuit to ground or
overload ≥15 mA

750-560 [2 AO 0-10V DC 10Bit 10mA 24V] • 9
Schematic Diagram
WAGO-I/O-SYSTEM 750
I/O Modules
2.1.1.4 Schematic Diagram
750-560
1
2
3
4
5
6
7
8
AO 1 AO 2
24 V
0V
Shield
(screen)
AO Logic
Function
270 pF
10 nF
Shield
(screen)
24 V
0V
10 nF
Error
Fig. 2.1.1-3: 2-Channel Analog Output Module 750-560 g056001e

10 •750-560 [2 AO 0-10V DC 10Bit 10mA 24V]
Technical Data
WAGO-I/O-SYSTEM 750
I/O Modules
2.1.1.5 Technical Data
Module Specific Data
Number of outputs 2
Voltage supply via Power Jumper Contacts
DC 24 V (-15 % ... +20 %)
AC 24 V (-15 % ... +10 %), 50 Hz ( -5 % ... +5 %)
Current consumption typ. (internal) 16 mA
Signal voltage 0 V ... 10 V
Load impedance > 1 kΩ
Resolution 10 Bit
Conversion time typ. 10 ms
Measuring error 25°C <±0.2 % of the full scale value
Temperature coefficient <±0.02 % /K of the full scale value
Isolation 500 V (Field/System)
Bit width 2 x 16 bits data
2 x 8 bits control/status (option)
Dimensions (mm) W x H x L 12 x 64* x 100
* from upper edge of 35 DIN rail
Weight ca. 55 g
Standards and Regulations (cf. Chapter 2.2 of the Coupler/Controller Manual)
EMC-Immunity to interference (CE) acc. to EN 50082-2 (96)
EMC-Emission of interference (CE) acc. to EN 50081-1 (93)
Approvals (cf. Chapter 2.2 of the Coupler/Controller Manual)
Conformity Marking
More Information
Detailed references to the approvals are listed in the document "Overview
Approvals WAGO-I/O-SYSTEM 750", which You can find on the CD ROM
ELECTRONICC Tools and Docs (Item-No.: 0888-0412-0001-0101) or in the
Internet under:
www.wago.com -> Service /Downloads /Documentation
/WAGO-I/O-SYSTEM 750/System Description/.