Waldorf GP8910E User manual

Installation and Operation Manual
GP8910E
GP8910EC
Electric Griddle Ranges
Date Purchased
Serial Number
Dealer
Service Provider
230379-8
For use in GB & IE
GPL8910E
GPL8910EC
GPB8910E
GPB8910EC
GPLB8910E
GPLB8910EC

The reproduction or copying of any part of this manual by any means whatsoever is strictly forbidden unless authorized previously in
writing by the manufacturer.
In line with policy to continually develop and improve its products, Moffat Ltd. reserves the right to change the specifications and
design without prior notice.
© Copyright Moffat Ltd. November 2014.
MANUFACTURED BY
Moffat Limited
Rolleston 7675
New Zealand
INTERNATIONAL CONTACTS
AUSTRALIA
Moffat Pty Limited
Web: www.moffat.com.au
E.Mail: [email protected]
Main Office: (tel) [phone]
(fax) [phone]
Service: (tel): 1800 622 216
Spares: (tel): 1800 337 963
Customer Service: (tel): 1800 335 315
(fax): 1800 350 281
CANADA
Serve Canada
Web: www.servecanada.com
E.Mail: [email protected]
Sales: (tel): 800 551 8795 (Toll Free)
Service: (tel): 800 263 1455 (Toll Free)
NEW ZEALAND
Moffat Limited
Web: www.moffat.co.nz
E.Mail: [email protected]
Main Office: (tel): 0800 663328
UNITED KINGDOM
Blue Seal
Web: www.blue-seal.co.uk
E.Mail: [email protected]
Sales: (tel): [phone]
(fax): [phone]
Spares: (tel): [phone]
(fax): [phone]
Service: (tel): [phone]
(fax): [phone]
UNITED STATES
Moffat
Web: www.moffat.com
Sales: (tel): 800 551 8795 (Toll Free)
(tel): [phone]
(fax): [phone]
Service: (tel): 800 858 4477 (Toll Free)
(tel): [phone]
(fax): [phone]
REST OF WORLD
Moffat Limited
Web: www.moffat.co.nz
E.Mail: [email protected]

Contents
Waldorf Electric Griddle
GP(L)(B)8910E Electric Griddle Range, Static Oven 900mm.
GP(L)(B)8910EC Electric Griddle Range, Convection Oven 900mm.
Introduction ............................................................................................. 2
Specifications ........................................................................................... 3
Model Numbers Covered in this Specification
General
Electrical Supply Requirements
Electrical Connection
Dimensions
Installation ................................................................................................ 5
Installation Requirements
Unpacking
Location
Clearances
Assembly
Electrical Connection
Commissioning
Operation................................................................................................... 8
Operation Guide
Description of Controls
Griddle
Oven
Cleaning and Maintenance ...................................................................... 10
General
After Each Use
Daily Cleaning
Weekly Cleaning
Periodic Maintenance
Fault Finding............................................................................................ 13
Circuit Schematics................................................................................... 14
Replacement Parts List ........................................................................... 17

2
Introduction
We are confident that you will be delighted with your WALDORF Electric Griddle Range, Static / Convection
Ovens and they will become a most valued appliance in your commercial kitchen.
To ensure you receive the utmost benefit from your new WALDORF appliance, there are two important
things you can do.
Firstly:
Please read the instruction book carefully and follow the directions given. The time taken will be well
spent.
Secondly:
If you are unsure of any aspect of the installation, instructions or performance of your appliance,
contact your WALDORF dealer promptly. In many cases a phone call could answer your question.
CE Only:
These instructions are only valid if the country code appears on the appliance. If the code does not
appear on the appliance, refer to the supplier of this appliance to obtain the technical instructions for
adapting the appliance to the conditions for use in that country.
WARNING:
IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY
DAMAGE, INJURY OR DEATH. READ THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS
THOROUGHLY BEFORE INSTALLING OR SERVICING THIS APPLIANCE.
WARNING:
GREAT CARE MUST BE TAKEN BY THE OPERATOR TO USE THE EQUIPMENT SAFELY TO GUARD IT AGAINST RISK
OF FIRE.
 THE APPLIANCE MUST NOT BE LEFT ON UNATTENDED.
 ITIS RECOMMENDED THAT AREGULAR INSPECTION IS MADE BY ACOMPETENT SERVICEMAN TO ENSURE
CORRECT AND SAFE OPERATION OF YOUR APPLIANCE IS MAINTAINED.
 DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPOURS OR LIQUIDS IN THE VICINITY OF
THIS OR ANY OTHER APPLIANCE.
 DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.
C AUTION :
This appliance is;
 For professional use and is to be used by suitably qualified / trained
persons only.
 Only authorised service persons are to carry out installation, servicing and
gas conversion operations.
 Components having adjustments protected (e.g. paint sealed) by the
manufacturer should not be adjusted by the user / operator.
 DO NOT operate the appliance without the legs supplied fitted.

3
Specifications
Model Numbers Covered in this Specification
GP[1]8910E Electric Griddle Range, Static Oven 900 mm wide.
GP[1]8910EC Electric Griddle Range, Convection Oven 900 mm wide.
NOTE:
[1]: - Model Options;
- - Standard.
L - Low Back.
B - Bold Front.
LB - Low Back and Bold Front.
General
A commercial heavy duty, 900mm wide, Electric Griddle Range, designed for modular kitchens and
constructed in an easy clean stainless steel external finish. The griddle elements are constructed
using stainless steel sheathed heating elements with dual thermostatic control zones.
The Griddle uses a 20mm thick griddle plate with the option of either ribbed or chromed mirror plate
options.
The range can be equipped with either an electric 6.5kW convection or static oven, 900mm wide.
Electrical Supply Requirements
Electrical Connection
Electrical supply connection point is located at the rear of the appliance, approximately 80 mm from
the right hand side and 467 mm from the rear and 150 mm from the floor.
When connecting a Waldorf electric appliance to the main supply, ensure that the following is carried
out:-
 An isolating switch is fitted within 2 m of the appliance, but not on the appliance and in
such a position that the user does not have to reach across the cooking surface.
 Supply cord shall be oil-resistant, sheathed flexible cable and not lighter than ordinary pol-
ychloroprene or other equivalent synthetic elastomer sheathed cord (as per AS / NZS 3191
part 2.10.11. or IEC 60245-IEC-57) e.g. H05 RN-F Type.
 The branch supply line shall be individually overload protected to the correct current rating
and the supply chord shall be protected against any mechanical or thermal damage.
 A grommet is fitted around the wiring entry hole into the appliance.
 All wiring connections must be tight.
Refer to the appropriate wiring standards for the size of cable that is to be supplied to an appliance
for the current drawn on that line.
MODEL Fan Motor
GP8910E 18.5 kW
L1 - 24.6 Amps
L2 - 25.6 Amps
L3 - 25.6 Amps
---------
GP8910EC 18.9 kW
L1 - 25.9 Amps
L2 - 25.6 Amps
L3 - 25.6 Amps
100W
3-Phase Connection
3P+N+E
400-415V, 50/60Hz
WARNING:
THIS APPLIANCE MUST BE EARTHED. IFTHE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY ASUITABLY
QUALIFIED PERSON IN ORDER TO AVOID AHAZARD.

4
Dimensions
GP(L)8910E / EC

5
Installation Requirements
NOTE:
 It is most important that this appliance is installed correctly and that operation is correct
before use. Installation shall comply with local electrical and health and safety
requirements.
 This appliance shall be installed with sufficient ventilation to prevent the occurrence of
unacceptable concentrations of health harmful substances in the room, the appliance is
installed in.
Waldorf Electric Griddle Ranges Electric Static / Convection Oven are designed to provide years of
satisfactory service and correct installation is essential to achieve the best performance, efficiency and
trouble-free operation.
This appliance must be installed in accordance with National installation codes and in addition, in
accordance with relevant National / Local codes covering electrical, fire and health and safety.
Australia / New Zealand AS / NZS3000 - Wiring Rules.
United Kingdom: BS 7671 - Requirements for Electrical Installations.
Installations must be carried out by authorised persons only. Failure to install equipment to
the relevant codes and manufacturer’s specifications shown in this section will void the
warranty.
Components having adjustments protected (e.g. paint sealed) by the manufacturer are only
to be adjusted by an authorised service agent. They are not to be adjusted by the installation
person.
Unpacking
 Remove all packaging and transit protection from the appliance including all protective plastic
coating from the exterior stainless steel panels.
 Check equipment and parts for damage. Report any damage immediately to the carrier and
distributor.
 Ensure that the adjustable feet / castors are securely fitted.
 Report any deficiencies to the distributor who supplied the appliance.
 Check that the available electrical supply is correct to that shown on the rating plate (Refer to the
dimension drawings for rating plate location).
Location
1. Installation must include adequate clearance and ventilation, to prevent dangerous build up of
combustion products.
2. Never directly connect a ventilation system to the appliance flue outlet.
3. Position the appliance in its approximate working position.
4. The legs / castors must always be fitted to the base of the appliance.
5. Components having adjustments protected (e.g. paint sealed) by the manufacturer are only to be
adjusted by an authorised service agent. They are not to be adjusted by the installation person.
NOTE: Do not obstruct or block the appliances flue. Never directly connect a ventilation system to
the appliance flue outlet.
Clearances
NOTE: Only non-combustible materials can be used in close proximity to this appliance.
Installation
Combustible Surface Non Combustible Surface
Left / Right Hand Side 250 mm 0 mm
Rear 50 mm 0 mm

6
Assembly
All Models
All models come pre-assembled.
NOTE: This appliance is fitted with adjustable feet / castors to enable the unit to be positioned
securely and level. This should be carried out on completion of the electrical connection.
Refer to the 'Electrical Connection' section.
Optional Accessories (Refer to Replacement Parts List)
 Plinth Kit. For installation details, refer to the instructions supplied with each kit.
Electrical Connection
NOTE: ALL ELECTRICAL CONNECTIONS MUST ONLY BE CARRIED OUT BY AN AUTHORISED
PERSON.
Each appliance should be connected to an adequately protected power supply and isolation switch mounted
adjacent to, but not behind the appliance. This switch must be clearly marked and readily accessible in
case of fire.
1. Check that the electricity supply is correct as shown on the Rating
Plate. (Refer to the dimension drawings for rating plate location).
2. The supply terminal connections are located at the rear of the the
appliance. Refer to ‘Electrical Connections’ in the ‘Specifications’
section of the manual.
3. Remove the control panel to allow connection access for the
electrical supply.
4. Bring the supply cable up through the grommet at the back of the
appliance and through the compression type gland provided on
the rear of the main electrical switchgear panel.
5. Connect the mains supply to L1, L2 and L3 fuse carrier
connections for 3 phase.
6. Connect neutral and earth conductors to neutral stud and earth
stud respectively.
7. For all connections ensure that conductors are secure and
appropriately terminated.
8. Tighten the cable gland to secure against tension on the cable.
NOTE:
 This appliance must be grounded / earthed.
 Fixed wiring installations must incorporate an all-pole disconnection switch.
9. Correctly locate the appliance into its final operating position and using a spirit level, adjust the legs
so that the appliance is level and at the correct height.
10. Connect the power supply to the appliance.
11. Check that the electrical supply is as shown in the 'Specifications' section.
Installation
C AUTION :
 This appliance is for professional use and is to be used by suitably
qualified / trained persons only.
 Only qualified service persons are to carry out installation and servicing of
this appliance.
WARNING:
THIS APPLIANCE MUST BE EARTHED. IFTHE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY ASUITABLY
QUALIFIED PERSON IN ORDER TO AVOID AHAZARD.
Fig 1
Rating Plate
Location

7
Installation
Commissioning
1. Before leaving the new installation;
a. Check the following functions in accordance with the operating instructions specified in the
'Operation' section of this manual.
 Check the current draw and loading for the equipment. Refer to the 'Specification' section
for the correct electrical requirements.
 Check that all the connections are correct and that all cover panels have been re-fitted.
 Check that the appliance functions in accordance with the operating instructions.
 Ensure that this instruction manual is left with the appliance.
 Ensure that all the relevant details and contacts have been added to the front of this
manual.
b. Ensure that the operator has been instructed in the areas of correct operation and shutdown
procedure for the appliance.
2. This manual must be kept by the owner for future reference and as a record of
Date of Purchase,
Date of Installation and Serial Number of Unit recorded and kept with this manual. (These
details can be found on the Rating Plate. (Refer to the dimension drawings for rating
plate location).
NOTE:
 If for some reason it is not possible to get the appliance to operate correctly, turn off the
electrical power supply and contact a qualified service person. The supplier of this
appliance will be able to recommend a suitable person.
 Make sure that the electrical supply is turned off before any service or maintenance work
is carried out.

8
Operation
Operation Guide
1. Waldorf Electric Griddle Range, Electric Static / Convection Oven have been designed to provide
simplicity of operation and 100% safety protection.
2. Improper operation is therefore almost impossible, however bad operating practices can reduce the
life of the griddle and produce a poor quality product. To use this appliance correctly please read
the following sections carefully:-
 Griddle.
 Oven.
Description of Controls
Griddle Control
Knob
With temperature
Gradient of 50°C to
320°C
Heating Indicator
Lamps (Amber)
Power Indicator
Lamps (Green)
C AUTION :
 This appliance is for professional use and is only to be used by suitably qual-
ified / trained persons.
 Only qualified service persons are to carry out installation and servicing of
this appliance.
Oven Thermostat
Control Knob
๐OFF Position
50°C to 300°C
Temperature
Graduations
Oven Top Heat Control
๐OFF Position
LOW Position
1Position
2Position
3Position
4Position
HIGH Position
Fig 2
Power Indicator
Lamp (Green)
Heating Indicator
Lamps (Amber)
for Top &
Bottom Elements

9
Operation
Griddle
1. Turn 'ON' the power at the mains supply, the green neon will illuminate.
2. Turn the thermostat control knob to the desired temperature. When the amber neon goes out, the
desired temperature has been reached and the griddle is ready for use.
NOTE: Turning the control to a higher setting than required will not shorten the heat up time.
3. To turn 'OFF' the griddle, turn the thermostat control knob to the lowest setting and turn 'OFF' the
mains power to the griddle.
4. Both the amber and green neons should not be illuminated.
Oven
The oven is fitted with top and bottom elements. The thermostat maintains the overall oven
temperature. The top element is further controlled by the oven top heat control. Convection ovens
(GP8910E / EC) are fitted with a circulation fan.
NOTE: The Thermostat on the oven provides overall control of the temperature within the oven by
controlling both elements, where as the Oven Top Heat Control provides a means of
balancing the distribution of heat between the top and bottom of the oven.
Place oven racks in desired position.
Preheat:
Preheat the oven by selecting the desired temperature, and turning the oven top heat control (Refer
to Fig 5 on the previous page) to a maximum of 2. When the desired temperature is reached, the
amber neon will go out.
Cooking:
When the desired temperature has been reached, load the oven with product and set the oven top
heat control to the desired setting.
NOTE: When the oven top heat control is set to a high setting, proportionally more heat is
produced at the top of the oven. (This can be used for browning, etc, during the cooking
operation). With the oven top heat control set on a low setting, less heat is produced from
the top oven elements. (This mode is used for general baking purposes to prevent cakes,
etc, from getting too brown and crisp on the top, but allow the cake to cook through).
To obtain more top heat during cooking, turn the oven top heat control to a higher position. (The
higher the setting, the more top heat).
Turning ‘OFF’ the Oven:
a. Turn the oven top heat control to the ‘O’ off position. The top heating will be turned ‘OFF’ and
the upper heating indicator lamp (Amber) will extinguish.
b. Turn the thermostat control knob to the ‘O’ off position and the lower heating indicator lamp
(Amber) will extinguish. The oven is now turned ‘OFF’.
! IMPORTANT DO NOT USE aluminium foil or trays directly on the cast iron sole plate(s).
NEVER block or cover the openings on each side of the sole plate(s).
! IMPORTANT DO NOT USE aluminium foil or trays directly on the cast iron sole plate(s).
NEVER block or cover the openings on each side of the sole plate(s).

10
Cleaning and Maintenance
General
Clean the griddle regularly. A clean appliance looks better, will last longer and will perform better.
Carbonised grease on the surface or on the griddle plate will hinder the transfer of heat from the
cooking surface to the food. This will result in loss of cooking efficiency.
NOTE: Each Heavy Duty Griddle is supplied with a scraper tool and a pack of blades for cleaning
the griddle surface.
- 1 Flat Blade (pack) - 1 Ribbed Blade (pack) and 2 handles for Ribbed Heavy Duty Griddle.
- 1 Flat Blade (pack) and I handle for Smooth Heavy Duty Griddle.
NEVER use the ribbed scraper blade on the flat chrome surfaced griddle plate.
Replacement blades and handles can be purchased separately. Refer to the 'Replacement
Parts List' at the rear of the manual.
DO NOT use water on the griddle plate while this item is still hot as warping and
cracking may occur. Allow the griddle plate to cool down before cleaning.
NOTE:
 DO NOT use abrasive detergents, strong solvents or caustic detergents as they could
corrode or damage the range.
 In order to prevent the forming of rust on the griddle plate (Steel Plate), ensure that any
detergent or cleaning material has been completely removed after each cleaning. The
appliance should be switched on briefly to ensure the griddle plate becomes dry. Oil or
grease should be spread over the griddle surface in order to form a thin protective greasy
film.
To keep your griddle clean and operating at peak efficiency, follow the procedures shown below:-
After Each Use
1. Clean the griddle with the scraper tool to remove any food debris.
2. Always ensure that the scraper tool blades are changed regularly to ensure that the scraper tool
works efficiently and prevents damage to the griddle plate surface.
C AUTION :
Always turn off the electrical supply at the mains before cleaning.
This appliance is not water proof.
Do Not use water jet spray to clean interior or exterior of this appliance.
WARNING:
THE BLADES FITTED TO THE SCRAPER TOOL ARE EXTREMELY SHARP AND ARE TO BE USED WITH CARE.
C AUTION :
Always ensure that an even pressure is applied over the whole surface of the
scraper tool when using on the flat chromed surface of the griddle, to prevent
scoring of the surface.
NEVER bang the sharp edge of the scraper tool on the flat chromed surface of
the griddle as this will damage the chrome finish and invalidate the warranty.

11
Cleaning and Maintenance
Daily Cleaning
1. The grease drawer should be checked and emptied frequently to prevent overflow and spillage.
Remove the grease drawer while still warm so that the grease is in a liquid state. Empty any grease
from the drawer and wash thoroughly in the same manner as any cooking utensil.
2. Clean the Control Panel with a damp cloth lightly moistened with a solution of mild detergent and
water.
3. Thoroughly clean the splash back, the interior and exterior surfaces of the range with hot water, a
detergent solution and a soft scrubbing brush.
4. Brush the griddle surface with a soft bristled brush. Any carbon deposits should be removed using
the supplied scraper tool followed by wiping with a cloth to prevent accumulation of food
deposits.
5. Dry the griddle thoroughly with a dry cloth and polish with a soft dry cloth.
NOTE: Chrome Griddle Plate; DO NOT use abrasive detergents, strong solvents or caustic
detergents as they could corrode or damage the chrome plate.
Weekly Cleaning
NOTE:
 If the Range usage is very high, we recommend that the weekly cleaning procedure is
carried out on a more frequent basis.
 Ensure that protective gloves are worn during the cleaning process.
 DO NOT use harsh abrasive detergents, strong solvents or caustic detergents as they will
damage the range and burners.
 DO NOT use water on the griddle plates while they are still hot as warping may occur.
Allow these items castings to cool and remove for cleaning.
Griddle - Steel Plate
NOTE: In order to prevent the forming of rust on the griddle plate, ensure that all detergent and
cleaning material has been entirely removed after each cleaning process. The appliance
should be switched on briefly to ensure the griddle plate becomes dry. Oil or grease should
be spread over the griddle surface in order to form a thin protective greasy film.
a. Remove and clean the grease collection drawer frequently to prevent over spills.
b. Clean the griddle surface thoroughly with a scraper tool or a wire brush. If necessary use a
griddle stone or a scotch bright pad on the griddle surface for the removal of stubborn or
accumulated carbon deposits.
c. Occasionally bleach the griddle plate with vinegar when the plate is cold.
d. Clean with hot water, a mild detergent solution and a scrubbing brush. Dry all components
thoroughly with a dry cloth.
e. The griddle should be switched on briefly to ensure that the griddle plate becomes dry. A thin
smear of cooking oil should be spread over the griddle in order to form a protective film.
Griddle - Chrome Plate
NOTE: In order to maintain the finish on the chrome griddle plate, ensure that all detergent and
cleaning material has been entirely removed after each cleaning process. The appliance
should be switched on briefly to ensure the griddle plate becomes dry.
C AUTION :
Always ensure that an even pressure is applied over the whole surface of the
scraper tool when using on the flat chromed surface of the griddle, to prevent
scoring of the surface.
NEVER bang the sharp edge of the scraper tool on the flat chromed surface of
the griddle as this will damage the chrome finish and invalidate the warranty.

12
Cleaning and Maintenance
a. Remove and clean the grease collection drawer frequently to prevent over spills.
b. Clean the griddle surface thoroughly with the supplied scraper tool.
c. Allow the plate to cool, then clean the plate with a scrubbing brush, a mild non-abrasive
detergent and water.
d. Occasionally bleach the plate with vinegar when cold.
e. Dry the griddle thoroughly with a dry cloth and polish with a soft dry cloth.
f. The griddle should be switched on briefly to ensure that the griddle plate becomes dry.
Griddle Cooking Area
a. Clean the griddle cooking area with a soft cloth and a mild detergent and hot water solution.
b. Baked on deposits or discolouration may require a good quality stainless steel cleaner or stainless
steel wool. Always apply cleaner when the appliance is cold and rub in the direction of the grain.
c. Remove the grease drawer and clean with a mild anti bacterial detergent and hot water solution
using a soft bristled brush. Dry the grease drawer thoroughly with a dry cloth.
Oven Interior
a. Do not use wire brushes, steel wool or other abrasive materials to clean the oven interior.
b. Clean the oven regularly with a good quality domestic oven cleaner.
c. Once a week, remove and clean any built up of grease etc. from the oven racks and the bottom
spill over cover.
Stainless Steel Surfaces
a. Clean the exterior surfaces of the griddle with hot water, a mild detergent solution and a soft
scrubbing brush. Note that the control knobs are a push fit onto the spindles and can be
removed to allow cleaning of the front control panel.
b. Baked on deposits or discolouration may require a good quality stainless steel cleaner or stainless
steel wool. Always apply cleaner when the appliance is cold and rub in the direction of the grain.
c. To remove any discolouration, use an approved stainless steel cleaner or stainless steel wool.
Always rub in the direction of the grain.
d. Remove the grease tray and clean with a mild anti bacterial detergent and hot water solution
using a soft bristled brush.
e. Dry the grease tray thoroughly with a dry cloth.
f. Dry all components thoroughly with a dry cloth and polish with a soft dry cloth.
Periodic Maintenance
To achieve the best results, cleaning must be regular and thorough and all controls and mechanical
parts should be checked and adjusted periodically by a competent serviceman. If any small faults
occur, have them attended to promptly. Don't wait until they cause a complete breakdown. It is
recommended that the appliance is serviced every 6 months.

13
Fault Finding
NOTE: Components having adjustments protected (e.g. paint sealed) by the manufacturer, are only
to be adjusted by an authorised service agent. They are not to be adjusted by an
unauthorised service person.
This section provides an easy reference guide to the more common problems that may occur during the
operation of your equipment. The fault finding guide in this section is intended to help you correct, or at
least accurately diagnose problems with your equipment.
Although this section covers the most common problems reported, you may encounter a problem not
covered in this section. In such instances, please contact your local authorised service agent who will
make every effort to help you identify and resolve the problem. Please note that the service agent will
require the following information:-
 The Model Trade Name and the Serial Number of the Appliance. (both can be found on the
Technical Data Plate located on the appliance. (Refer to the ‘Dimensions’ section).
Fault Possible Cause Remedy
Element does not work when
turned ‘ON’.
Check individual fuses located
behind the control panel.
Check for an electrical short by
checking that there is NO
continuity between any "phase
in" line and the metal appliance
body itself.
Check for the item failing
(element, control etc) by using a
multimeter as shown on following
pages.
Replace the blown fuse.
Call the service provider.
Complete power failure of the
appliance
Check fuse connection at the
mains supply.
Ensure that the fuse size is
correct to carry the load.
Check for an electrical short to
the appliance.
Replace the blown fuse.
Carry out a continuity and
resistance check on the appliance.
Call the service provider.

14
Circuit Schematics
GP8910E / GP8910EC Griddle Wiring Schematic
21
31 11
22
32 12
EARTH STUD M6
EARTH STUD
3/16"
EARTH
STUD M6
7
9
9
9
1
1
1
3
2
2
7
7
6
10
10
10
76
88
4
4
5
11
12
13
14
7
1
1
1
3
2
2
7
7
6
9
9
9
76
88
4
4
5
11
13
14
10
10
10
12
11
22
32 12
3P3
4P4
CONTROL PANEL
GRIDDLE PLATE
21
31 11
22
32 12
15
16
15
16
THERMOSTAT
229146
SWITCH
229145
2
1
P2
P1
NEON GREEN
227962
NEON
AMBER
227963
OVERTEMP
THERMOSTAT
229353
21
31
REAR SUPPLY ENTRY
THERMOSTAT
229146
SWITCH
229145
2
1
P2
P1
NEON GREEN
227962
NEON
AMBER
227963
OVERTEMP
THERMOSTAT
229353
21
31 11
22
32 12
3P3
4P4

15
Circuit Schematics
GP8910E (Static Oven) Wiring Schematic

16
Circuit Schematics
GP8910EC (Convection Oven) Wiring Schematic

17
Replacement Parts List
When ordering replacement parts, please quote the part number and the description as listed below.
If the part required is not listed below, request the part by description and quote model number and
serial number which is shown on the rating plate.
Griddle
227399 Control Knob - 50°C to 300°C.
229146 Thermostat - 50°C to 300°C.
229353 Overtemp 360°C, 3 Pole.
229145 Switch 4 Pole.
227962 Neon Green.
227963 Neon Amber.
228571 Index Mark Moulding.
229245 Element 2000W.
228400 Grease Drawer.
229224 Control Panel Hinge.
Griddle Plate Options
Oven
228082 Oven Top Element 2kW.
228059 Oven Bottom Element 4.5kW.
228704 Door Spring Kit.
026160 Terminal Block Mains.
227399 Control Knob - 50°C to 300°C.
229146 Thermostat - 50 - 300°C.
229145 Switch (4-pole).
227962 Neon Green.
227963 Neon Amber.
013989 Energy Regulator.
227398 Control Knob HI/LO Heat.
Convection Oven Only
228938 Oven Door Microswitch.
010909 Motor Capacitor 4µf.
228116 Fan.
019479 Motor.
Replacement Parts List
IMPORTANT:
Only genuine authorized replacement parts should be used for the servicing and
repair of this appliance. The instructions supplied with the parts should be followed
when replacing components.
For further information and servicing instructions, contact your nearest authorized
service branch (contact details are as shown on the reverse of the front cover of this
manual).
Griddle Plate Standard Chromed (-C) Ribbed
900 mm 229248 229270
ON REQUEST,
Various options (depending on ribbed
section width on LH or RH side).

18
General
227892 Side Rack LH.
227893 Side Rack RH.
227896 Oven Rack.
228571 Index Mark Moulding.
227850 Leg 150 mm (Adjustable).
Accessories
228566 Griddle Scraper Tool.
228567 Smooth Plate Scraper Blades (Pack of 5 blades).
233817 Ribbed Plate Scraper Blade (Individual Blade).
228799 900 mm Plinth Kit.
229674 Rear Roller Assy.
Replacement Parts List