Wali GSDM003S User manual

INSTALLATION MANUAL
[email protected]
75x75/100x100 30"
MAX (1~7kg)x3
(2. 2~15.4lbs ) x3
R AT E D
GSDM003S
Monitor Desk Mount

2

Supplied Parts List
3
Arm
A(x1)
Pole
B(x1)
Base
C(x1)
VESA Plate
E(x3)
Support Plate
K(x1)
C-Clamp Brace
F(x1)
C-Clamp
G(x1)
Décor Cover
H(x1)
Bolt
J(x2)
ARM
I(x1)
Clip Holder
D(x1)
Allen Key 4mm
P(x1)
Support Plate
L(x2)
Washer
M(x2)
Nut
N(x2)
Anti-skid Pad
O(x4)
M6x16 Bolt
U(x3)
Allen Key 6mm
Q(x1)
Wrench
R(x1)
M6x10 Bolt
S(x4)
M6x12 Bolt
T(x4)
X 3
M4x12 Bolt
M-A(x4)
M4x16 Bolt
M-B(x4)
M5x12 Bolt
M-C(x4)
M5x16 Bolt
M-D(x4)
D5 Washer
M-E(x4)
Spacer
M-F(x4)

4
Step 1
Step 2
1. Place the Pole Bonto the top hole of Base C,connect Pole B and Base Cfrom the bottom using M6x16 Bolt U
and tighten with Allen Key 4mm P; Connect C-Clamp Brace Fto Base Cfrom the bottom using M6x12 Bolt Tand
tighten with Allen Key 4mm P.Tear off the protect paper to attach Anti-Skid Pad Oto the bottom designated
position of Base Cas image shown.
Fit clamp: 0.39”-3.3”
Grommet: 0.39”-3.1”
Option A Clamp Installation
B
C
U
O
P
P
O
T
B
CF
UP

5
Step 2
1.97"-3.3"
0.39"-2.17"
Option A
Clamp Installation
3. Put on the Décor Cover Hto cover the C-Clamp Brace F, rotate the knob clockwise to fasten for stability.
or
S
H
S
H
F
F
G
2. Select the preferred height firstly and connect C-Clamp Gto C-Clamp Brace Fusing M6x10 Bolt Sand tighten with
Allen Key 4mm P .
P

6
Step 2
Option B
Grommet Base Installation
1. Guide Support Plate K through Bolt Jand connect them to Base Cfrom the bottom using M6x12 Bolt Tand
tighten with Allen Key 4mm P. Tear off the protect paper to attach Anti-Skid Pad Oto the bottom designated
position of Base Cas image shown.
0.39”-3.1”
P
T
K
J
O
L
M
N
R
R
N
L
M
C
J
K
P
T
J
O
If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface and the hole diameter is
larger than 2.75" before installing the desk mount. Insert the assembled Pole through the desk hole, guide the Support
Plate L,Washer Mand Nut Nthrough the Bolt J, rotate the Nut Nclockwise to fasten for stability.
2a Existing Grommet Hole Installation
2.75“

7
Step 2
Step 3
L
M
N
R
P
N
A
D
B
Q
L
M
R
Option B
Grommet Base Installation
Mark the position of the two holes on your mounting surface.Drill the two 3/8"(10mm) diameter holes at the marked position
through the mounting surface.Insert the assembled Pole through the desk holes, guide the Support Plate L,Washer Mand
Nut Nthrough the Bolt J, rotate the Nut Nclockwise to fasten for stability.
2b Self-drilled Grommet Hole Installation
ø 10mm
(ø ") 3/8
Put the Clip Holder Dand Arm Athrough the Pole B, adjust the preferred height and tighten using Allen Key 6mm Q.
J
0.39”-3.1”

Grommet Base Installation
8
Step 4
Step 5
Step 5.1
Select TV Screws
Step 5.2
Select Spacers ( if needed )
Hand thread screws
into the threaded
inserts on the back of
your TV to determine
which screw diameter
(M4 or M5) to use.
M4 M5
I
Put the Arm Ithrough the Pole B, adjust the preferred height and tighten using Allen Key 6mm Q.
I
B
Q

9
Step 5
Step 6
12
A
Pull the buckle and put the assembled TV/Monitor onto the Arm Aand ensure the stability.
Step 5.3a Step 5.3b
Select M4x12 Bolt M-A or M5x12 Bolt M-C
according to your TV/Monitor,connect VESA Plate E
together with D5 Washer M-E into the mounting
holes on the back of TV/Monitor, tighten with
screwdriver.(Screwdriver needed but not included)
Select M4x16 Bolt M-B or M5x16 Bolt M-D
according to your TV/Monitor,connect VESA Plate E
together with D5 Washer M-E and Spacer M-F into
the mounting holes on the back of TV/Monitor,
tighten with screwdriver.(Screwdriver needed but not
included)
E
E
M-E
M-E
M-C
M-A
E
M-E
M-F
M-B
M-D
E

10
Step 7
Step 8
Pull the bottom two cable slot covers to the VESA direction to detach it off the arm, open the four corner button of the
top cable slot cover to detach it off.
Press the Arm Aon horizontal level as image shown, adjust gas spring tension to your personal preference using Allen
Key 6mm Q, adjust the tilt tension using Allen Key 6mm Q.
P
P
For Heavier Monitors
For Lighter Monitors
A
Q
Q

11
Step 9
Guide the cable through the cable slot and put the cover back to arm.
Step 10
Manually swivel,tilt or rotate the angle for the best operating environment; Store the Allen Key 4mm Pand Allen
Key 6mm Qin the holder of Décor Cover Dfor future convenience.
+90°
-90°
±90°
±90°
±180°
±180°
±135°
I
2
Q
P
D
1

1-844-SATTLER (18447288537) [email protected]
If you have any questions,please contact us.
  
We support the technology that brings your home to life.
We offer high quality products, professional customer service,
and extensive technical support.