Walkera VOYAGER 4 User manual

www.walkera.com
DEVO F18 Remote Controller
QUICK START GUIDE
Oct. 18th 2018
V1.1

-2-
4
3
7
7-8
8
9-10
6
10
11
18
21
10
11
5
6
6
1.0 Get to know your aircraft
2.0 Get to know your Remote Controller
3.0 Specifications
4.0 Attention Before Flight
5.0 Check Battery Levels
6.0 Charge the Batteries
7.0 Download and install the software APP
8.0 APP Main Screen Instructions
9.0 Prepare the Remote Controller
10.0 Prepare the VOYAGER 4
11.0 Ready to fly
12-17
17
10
18
18
19
20
20
11.1 Starting the aircraft / Get binding
11.2 Connect to APP Software
11.3 GPS indicator light
11.4 Motor Unlock / Lock
12.0 Operation Instruction
13.0 End flight
14.0 Additional remarks
14.1 Introduction for FCS-V4 Main Flight Controller
14.2 Compass Calibration
14.3 Remote Controller stick mode switch and stick calibration
14.4 Introduction for DEVO-RX715 receiver
14.5 Brushless ESC and Brushless Motor connection diagram
15.0 Intelligent Flight Battery Safety Guidelines
Contents

-3-
Modular design for electronic parts enable convenient connections and easy assembles.
Newly designing of new generation flight controller system ensure stabilized and reliable flight performance.
GPS and GLONASS dual navigation system ensure more accurate and safer flight experience.
Adopting new 4G communication image transmission technology.
Adopting 18X optical zoom/ 4K HD camera to obtain much clearer image and easier operating experience.
1.0 Get to know your aircraft
Travel Mode
Flight Mode
Landing Gear DownLanding Gear Up
Landing Mode
1. Gimbal and Camera
2. Landing Gear
3. Front LEDS ( Blue )
4. Rear LEDS ( Red )
5. CW motor
6. CCW motor
7. CW propeller( )
8. CCW propeller( )
9. Aircraft Status Indicators
10. Power Button
11. Battery Level Indicators
12. 4G SIM card port
13. Idle port
14. USB upgrade slot
15. 4G communication antenna
16. Camera memory card port
* 1) 4G communication cards for aircraft and mobile devices are purchased and installed by buyers.
2) The Maximum flight time of 20 minutes was obtained under test environment.
3) To avoid property loss and personal injury caused by wrong operation, please read the manual carefully and
watch the tutorial videos at www.walkera.com before flight.
Quick Start Guide

-4-
100
50
2510
2.0 Get to know your Remote Controller
DEVO-F18 with the built-in Bluetooth Module. Equipped with function like manual mode / GPS hold mode /
Return To Home, camera & Gimbal controlling, the VOYAGER 4 is easier to control.
(You can select the suitable flight mode according to your flying skill.)
14. Battery Level LEDs
15. Charging Indicator
16. Bluetooth blue LED
17. Charger socket
18. Power Button
19. Return To Home
20. AUX3
21. AUX2
22. Motion Mode(Common)
23. Beginner Mode
24. Antenna
25. Data transfer port
26. Upgrade port
27. Left Gimbal Dial
28. Right Gimbal Dial
29. Stop button
30. Skid landing comtrol button
31. Photo button
32. Video button
33. Training port
34. Enter key
1. Mobile Device Holder
2. AUTO Landing
3. AUTO Takeoff
4. Manual Mode
5. GPS Mode
6. Left stick
7. Right stick
8. Follow me mode
9. Circle flight
10. IOC
11. AUX4
12. Gimbal control stick
13. Status LED
Folded
The default setting is Mode 2. The left stick controls the aircraft's altitude and heading, while the right stick
controls its forward, backward, left and right movements.
Left Stick
Up
Down
Turn
Left
Turn
Right
Right Stick
Forward
Backward
Left Right
* Maximum transmission distance about 1.5km as measured under the experimental environment, for reference purpose only.
Quick Start Guide

-5-
465mm
382mm
465mm 352mm
3.0 Specifications
Aircraft
Gimbal
Camera
382mm
465 x 465 x 352mm
3250g(Battery included)
DEVO F18
FCS-V4
DEVO-RX715
WK-WS-42-002A
Voyager 4 (R/B)
22.2V 4500mAh 10C(6S) LiPo
About 20mins
-10℃~ +40℃
Main Rotor Dia.:
Overall (L x W x H):
Weight:
Remote Controller:
Main Controller:
Receiver:
Brushless Motor:
Brushless ESC:
Battery:
Flight Time:
Working Temperature:
Control accuracy:
Control range:
Remote Controller
Overall (L x W x H):
Working frequency:
Signal range:
Built-in battery:
165 x 174 x 62mm
2.4G
About 1.5KM (open without shelter, no electromagnetic interference)
7.4V 3000mAh Li-po 2S
Static: ±0.008°; Motion: ±0.08°; Shake-proof: ±0.008°
Pitch rotation -90°~ +45°; Horizontal ±150°
Sensor:
ISO Range:
Video Resolution:
Photo Resolution:
Focal Length:
Zoom Ratio:
Zoom Speed:
Horizontal View:
Close-shot Distance:
Video Storage Maximum:
Compress Standard:
Files Format:
Support Micro-SD:
1/2.3 SONY IMX117 CMOS
100-3200(Video) / 100-1600(Image)
4K 30fps
4608 x 3456
6.7-134.5mm
18x optical zoom
About 2.0s
59.8°- 3.0°(Wide Angle-Telescopic)
10 - 1500mm(Wide Angle-Telescopic)
32Kbps - 16Mbps
H.264 / H.265
JPG/MP4
SD/SDHC Card(MAX128G)
Quick Start Guide
62mm
165mm
174mm

-6-
100
50
2510
100
50
2510
A
A
B
B
1) This product is suitable for people who has flight experience of hobby model and ages 14 .
2) Do not fly in bad weather, such as windy, snowy, foggy etc..
3) Select the open, no-tall-buildings area. Extensive steel-used buildings will affect the compass,
blocking the GPS signal, causing worse on the aircraft positioning or even not able to locate.
4) Please keep away from highly spining parts(such as propellers and motors).
5) Please keep away from obstacles, people, water and so on.
6) Do not fly it in where there is high-voltage lines, communication base stations or radio towers, in order to
avoid signal interference.
7) Don’t fly in no-fly zone according to the local laws and regulations.
8) Flight performance will be effected with environment when flying above 4500m of sea levels,
as the battery and gravity system will be influenced.
4.0 Attention Before Flight
5.0 Check Battery Levels
Turn on the remote controller and intelligent flight Battery to check the battery level.
Be sure the battery was fully charged at the first use.
1) Long press the power button for 2~3 seconds to turn on the remote controller.
2) Long press the power button for 3~5 seconds to turn on Intelligent Flight Battery.
(Repeat above operation to turn off the intelligent flight battery and remote controller)
Low High
Low
High
1) Connect the charger to the AC power (100 ~ 240v 50/60hz).
2) Only use the walkera charger for your Intelligent Flight Battery and remote controller.
Please turn off the intelligent flight battery and remote controller before charging.
3) The Level indicator of intelligent flight battery light off means charging finished completely;
The charging indicator of remote controller turns green means remote controller charging finished completely.
6.0 Charge the Batteries
Power Outlet
100~240V
Quick Start Guide
+

-7-
8.0 APP Main Screen Instructions
In the interface, HD video and photographs can be real-time previewed, as well as the dynamic setting
parameters, such as aircraft, remote controller, Gimbal and battery.
Connected
Pos-Hold
GPS
GPS Available
4. Equipment connection status:
Connected or Disconnected.
3. Return [ ]: Return to last step.
6. The aircraft model: Display aircraft flight mode.
5. The flight time [ ] : Aircraft flight time.
7. Number of aircraft satellite [ ]:
Displays the received satellites of aircraft.
9. The remote controller signal strength [ ]:
Displays the signal level between remote controller and aircraft.
10. Camera signal [ ]
11. Battery Levels [ ]: Real-time display the
current Flight Battery remaining levels.
1. Auto Takeoff [ ]:
Click the button, the aircraft take off automatically.
2. Battery Levels return [ ]:
The remaining battery power of intelligent
flight reaches this point , the aircraft will
automatically return.
8. 4G signal [ ]: Displays the 4G communication signal strength.
Quick Start Guide
7.0 Downloading and Installing APP
Google Play
Android download Android download
APP software supports Android 5.1 and above systems iOS 9.0 and above,
Android system please download at Walkera official website (www.walkera.com) or go to Google play to search
for Walker Drone or scan the QR code to download and install;
iOS system please go to the APP Store to search for Walker Aircraft or scan the QR code to download and install.
iOS download

-8-
12. Setting [ ]: Click the icon to open the Setting menu, Normal setting, aircraft, remote controller, gimbal and battery can be charged.
18. Return to Home[ ]：
Click the button, the aircraft stop waypoint flying,
and return back automatically.
19. A thumbnail map icon:
Click on the thumbnail icon quickly switch to the map interface.
15. The camera zoom control: divided into wide Angle (W) and telescopic (T).
14. Photography and video switch [ ] :
Photo: photo button is used to trigger the camera take pictures. While this function also supported in the remote controller.
Video: video button to start/stop video. It can also press the video button on the remote controller for video.
17. Flight status parameters:
Distance: aircraft with returning point horizontal distance.
Height: aircraft with returning point vertical distance.
Horizontal velocity: the speed of vehicle in a horizontal direction.
Vertical speed: speed of aircraft in the vertical direction.
13. Camera Settings [ ]:
Touch icons it has preview settings, recording settings and so on. Under identical Video Size, the larger the stream Rate,
the better the picture quality, anyway, the video transmission distance is shortened accordingly.
16. GPS positing: GPS connected successfully displays “GPS Available”, GPS didn’t connect displays “GPS Unavailable”.
Map lock Map switch
Waypoint
Circle Fly
Waypoints
Connected
Pos-Hold
GPS
GPS Available
Unfold
Press the button to
release the clamp.
Place your mobile device and
adjust the clamp to secure.
Phone block
When you install the phone,
just open the phone block,
other operations the same
as 2, 3.
9.0 Prepare the Remote Controller
Strong
* Ensure that the aircraft is flying within the optimal transmission zone. To achieve the best transmission performance,
maintain the appropriate relationship between the operator and the aircraft.
Weak
Quick Start Guide

-9-
10.0 Prepare the VOYAGER 4
The factory default of the aircraft is Travel Mode. Before flying, connect to power, transform the aircraft
to Landing Mode, please don't use the outside force.
Travel Mode
Landing Mode
Transform the aircraft to landing mode, please hold the aircraft so as not to damage the Landing Gear.
If the red and blue lights are flashing alternately, it indicates the aircraft is not normal,
see the APP indications.
Attention:
Gimbal Lock
Positioning Column
Gimbal Console
Lock
Location Hole
Screw Hole
Position
Rotate the Gimbal Lock to the locked position
following to the direction of the arrow.
Tighten M3x3 screws to fix the Gimbal.
Install Gimbal and Camera
Remove gimbal cover.
Aim the gimbal positioning column to upper location hole ,
and rotate the white line of Gimbal lock to unlocked position,
align the white lines and insert the gimbal.
Insert the battery.
Power on the remote controller and the aircraft.
The red LED light flashes until goes out, indicating that
IMU preheating is complete and the code binding is successful.
(Automatically transform the aircraft to Landing Mode.)
Please turn off the remote controller and aircraft after finishing.
Quick Start Guide

-10-
Voyager 4-4G-4K
Voyager 4-WIFI-1080P
Voyager 4-WIFI-4K
Install propellers
Fix the CW propeller( ) onto the CW motor according to the
direction of blue arrow, and fix the CCW propeller( ) onto
the CCW motor according to the direction of orange arrow.
Tighten the propellers manually and make sure the propeller
is installed in proper way and fastened.
CW propeller
( )
CW propeller
( )
Front CCW propeller
( )
CCW propeller
( )
11.0 Ready to fly
Place the aircraft in a wide open space, with the rear facing you. (This position is known as “TAIL IN”)
11.1 Starting the aircraft / Get binding
Power on the remote controller.
Put the aircraft to the horizontal place and power on the aircraft.
The red LED light flashes until goes out, indicating that IMU preheating is complete and
the code binding is successful.
(If the red and blue lights are flashing alternately, it indicates the aircraft is not normal, see the APP indications.)
Open Bluetooth and Cellular Data for mobile device.
11.2 Connect to APP Software
1. Click the icon
on mobile device
The APP icon
2. Click “Select Model”,
select “Voyager 4-4G-4K”,
and then click “Go to Connect”.
3. Select remote controller(RC) ,
click “Connect”.
4. Remote control serial
number will pop up
automatically, click "serial
number and connect”.
5. Select the aircraft serial
number item, click “Setting”.
6. Click "Add", it will
pop up the input box.
7. Enter the serial number
of the aircraft, and note
the name, click "OK."
8. Click "Connect" to enter
the main interface.
Quick Start Guide

-11-
11.3 GPS indicator light
When the blue LED light (GPS) begin to flash,
you can work GPS function.
Method 2: Push the left stick and right stick down and move outward and hold for more than 2 seconds.
You will see the red LED light turns off, indicating that motors are locked.
Method 1: When the aircraft has landed, push and hold the throttle stick down.
The motors will stop after 5 seconds.
There are two methods to lock the motors.
Motor Lock
Method 1 Method 2
Circle
Motion
GPS
Manual
Motor Unlock
Attention:
11.4 Motor Unlock / Lock
When it has GPS signal, you can unlock under the GPS mode (GPS) or Manual mode or Motion mode.
Without the GPS signal, you can only unlock motors under Manual Mode.
After unlock the motor, if the flight does not start after 5 seconds,
the motor will automatically enter the locked state.
Push the switch to GPS mode or Manual mode or Motion mode, and push the left stick and right stick
down and move outward and hold for more than 2 seconds.
You will see the red LED light keeps on, indicating that motors are unlocked.
Motors will start rotating after unlocked, please release the stick.
Blue LED light
Quick Start Guide

-12-
Take
off
Landing
GPS
Manual
Take
off
Landing
GPS
Manual
Manual Manual
Take
off
Landing
GPS
Take
off
Landing
GPS
Manual
Take
off
Landing
GPS
Manual
Take
off
Landing
GPS
12.0 Operation Instruction
2) When the status indication on the top of the APP is shown as “Connected”,
the you can use the App to control the aircraft.
1) Make sure that the received GPS signal (Blue LED light blinks)
AUTO Takeoff (remote controller or APP operation)
Please unlock the motor before take off. (Unlocking method, please refer to 11)
Attention:
AUTO takeoff default height is 3m, when it need to manual control the throttle,
the throttle stick must be pushed to the midpoint or more, that it can remove AUTO takeoff mode.
Please click the icon in the APP
main interface, then the aircraft
will take off automatically.
Switch to “Take off”
position
Short press the Enter key,
aircraft will take off
automatically.
AUTO Landing (remote controller operation)
Ground
3m
Ground
Ground
Switch to “Landing”
position
Short press the Enter key,
aircraft will land
automatically.
1) When you used the function of “AUTO landing”, the landing gear of aircraft will be extended.
2) During the landing, you can operate the aircraft be forward and backward or right and left.
Attention:
GPS hold mode (Remote controller operation)
Switch to “GPS”
position
Short press the Enter key to
enter the GPS hold mode
Throttle stick
return neutral
Attention:
1) The first flight default to GPS Mode after each power on.
2) In the GPS mode, there are Altitude hold, fixed point, brake function, the flight speed is slower (≤5m/s).
3) If the GPS signal is poor or no signal, can only be Altitude hold, but not fixed point.
4) Switch to manual mode can not be fixed point.
Quick Start Guide

-13-
AUX3
Common
Beginner
AUX2
AUX3
Common
Beginner
AUX2
AUX4
IOC
Circle
flight
Follow me
AUX4
IOC
Circle
flight
Follow me
Ground
Motion mode (Remote controller operation)
Switch to “Common”
position
Short press the Enter key to
enter the Motion mode
Attention:
Attention:
1) In the Motion mode, there are Altitude hold, fixed point, brake function, the flight speed is faster (≤8m/s).
2) If the GPS signal is poor or no signal, can only be Altitude hold, but not fixed point.
3) Switch to manual mode can not be fixed point.
Circle flight (remote controller or APP operation)
Aircraft in
GPS hold mode
Switch to “Circle flight”
position
Short press the Enter key to
enter the circle flight mode
Please click the icon in the APP
interface, then the aircraft enter
circle flight mode.
1) The aircraft is under quiescent state when it enters auto-circling. The circling function can only work after you set circle speed
and direction by toggling aileron stick left or right (-5m/s to +5m/s speed changeable, Default is 0m/s).
Dial to the left,
Clockwise circles
Dial to the right,
Counterclockwise circles.
Speed: The larger volatility toggling and longer holding time,
the faster circling. The slower the contrary.
2) Dial elevator stick up or down to change circle radius
(5m-50m radius changeable, Default is 5m)
Dial up, Circle radius turns small
Dial down, Circle radius turns large
Quick Start Guide

-14-
25m
Long press this key(3-5 seconds)
on the remote controller and the
aircraft will return automatically
Click this key in the APP
interface and the aircraft
will return automatically
RETURN TO HOME (Remote controller or APP operation)
Aircraft with Home point horizontal distance > 30m
a. If the flight altitude is higher than 25m, the aircraft
will keep the current altitude and return above the
Home Point then descend vertically.
b. When the flight altitude is lower than 25m, the
aircraft will elevate automatically to 25m high
then fly back above the Home Point and land
vertically.
Aircraft with Home point horizontal distance < 30m
a. If the flight altitude is higher than 25m, the aircraft
will keep the current altitude and return above the
Home Point then descend vertically.
b. If the flight altitude is lower than 25m, the aircraft
will keep the current altitude and return above the
Home Point then descend vertically.
Attention:
1) To enter a key return, please don't move the other switches and buttons.
2) When the aircraft lost the remote controller signal, it will automatically enter Failsafe RTH.
3) When the aircraft battery voltage is too low, and aircraft with Home point horizontal distance is greater than 30m,
aircraft will automatically turn back. If the aircraft with the Home point horizontal distance less than 30m,
aircraft will decrease automatically from the current position and land.
4) GPS signal is not normal or GPS does not work, can not achieve the auto return, but will land automatically.
Height over HP＞25m
Height over HP＞25m
Height over HP＜25m
Height over HP＜25m
Elevate to 25m
Home Point
Home Point
Quick Start Guide

-15-
HOME
Hyper IOC Mode
IOC or Intelligent Orientation Control mode means that the aircraft’s flight direction is only relative to the
orignal take-off point (where you armed the motors). REGARDLESS of the actual aircraft headding, in this
mode you can fly past something and pan the aircraft to frame your shot, without having to worry what
direction the aircraft is facing.
1) During flying, the drone will enter hyper IOC mode when the distance between the flight position of drone
and the initial position where the GPS signal has been received is more than 10m.
2) When under hyper IOC mode, you can make the drone return to the initial position only by holding the stick backwards.
Attention:
Start
Exit
Add
Clear
Start
Exit
Add
Waypoints Flight (APP operation)
Waypoint Flight (APP operation)
Click the icon to enter the Waypoint Flight interface.
Click the icon to enter the Waypoints Flight interface.
AUX4
IOC
Circle
flight
Follow me
AUX4
IOC
Circle
flight
Follow me
Switch to “IOC”
position
Short press the Enter key to
enter the Hyper IOC mode
Mode2 (Throttle
stick on the left)
Quick Start Guide

-16-
0°
+150°
-150°
+45°
-90°
0°
Three-axis stabilization gimbal makes the camera steady so that it can shoot stable photos even fly
with hight altitude. And you can control pitch and horizontal angle of the gimbal by Gimbal stick
on Remote Controller or APP Software.
Control the gimbal (remote controller or APP operation)
Angle of Pitch
Angle of horizontal
Gimbal Stick
up or down.
In APP image interface
swipe up or down.
Gimbal Stick
Left or Right.
In APP image interface
swipe left or right.
Lock mode
Gimbal pointing stay
unchanged when
aircraft nose move
Attention:
1) You must select the mode first and then adjust the angle. In follow me mode, the horizontal angle (YAW) is not adjustable.
2) Gimbal stick position determines the rate of change of the gimbal: when the stick located at the midpoint the velocity is zero,
the greater the offset of the stick gimbal changes faster, whereas the slower.
Follow me mode
Gimbal pointing move with
aircraft nose direction
Switch to GREEN ARROW to Lock mode.
Switch to PURPLE ARROW to Follow me mode.
Connected
Pos-Hold
GPS
Connected
Pos-Hold
GPS
DownCenter
Quick Start Guide

-17-
Ｖideo
Photo
Remote Controller Operation
Take photo by
short pressing
the button of
Remote Controller
Video by short pressing the button
of Remote Controller
Quick Start Guide
Landing gear
Attention:
Landing gear Extended and Retracted (remote controller operation)
Extend landing gear Retract landing gear
1) Make sure the landing gear retracted after the aircraft takes off.
2) When the aircraft lands manually, extend the landing gear.
3) In the “RETURN TO HOME” Mode, the landing gear will extend automatically till the flight end.
Retract or Extend the
landing gear by short pressing
the button of Remote Controller.
Video and photo (remote controller or APP operation)
APP Operation
Slide downward:
adjust the telescope of zoom camera
Slide upward:
adjust the panorama of zoom camera
1) Choose working mode: photo or video
2) Touch the Photo or video icon to take photo or video
Photo or video icon
Working mode
T end: adjust the telescope of zoom camera
13.0 End flight
Manual landing or return to home function landing.
First, Power off the aircraft, then turn off the Remote Controller.
Finally, remove the battery from the aircraft.
W end: adjust the wide Angle of zoom camera
Left Gimbal Dial
Camera Settings

-18-
If there is circles or drift in flying, please calibrate the compass.
(the motor must be locked and rear red LED light turn off )
Please calibration outdoors and far away from strong electromagnetic interference.
Attention:
14.2 Compass Calibration
The compass calibration steps are as follows:
Do this by moving both sticks DOWN and to the
middle position at the same time about 5 seconds,
the aircraft red LED light flash quickly.
Rotate the aircraft 360 degrees in the horizontal
direction .
Rotate the aircraft in the vertical direction (aircraft head down) 360 degrees
until red LED light turn off, which Indicates that the calibration is successful,
and then the aircraft is still in the horizontal position.
If calibration is not successful, please re calibrate it according the above methods.
Ground
Head
vertical
down
14.0 Additional remarks
14.1 Introduction for FCS-V4 Main Flight Controller
Flexible flat cable connection
The metal surface of flexible flat cable
plug should be inserted upward to main
controller port properly.
The metal surface of flexible flat cable
plug should be inserted downward to
power board port properly.
1. GPS Port: connect GPS module
2. Micro SD: Micro SD card slot
3. UART Port: not used
4. USB port: used for upgrading
5. Connection port: used to connect flexible flat cable
Port introduction
Upgrading
Please upgrade online via
Walkera official website
USB Cable
USB port
www.walkera.com
Quick Start Guide

-19-
Stick Calibration:
Attention:
Long press " " button for 3 to 5 seconds, four lights flash alternately to enter stick calibration.
Operate the stick several times within mechanical tuning range and then back in the middle. Long press
the " " button for 3 to 5 seconds again, four indicator lights turn on, then exit stick calibration.
When you exit if vibrate alert, then the calibration fails, please recalibrate.
Tip:
14.3 Remote Controller stick mode switch and stick calibration
DEVO F18 stick mode and stick calibration has been set up before out of factory,
if you need to switch and calibration, please refer to the following methods.
It must be operated under power off or motors are locked well.
※Customization also supported in APP software.
Landing gear
Landing gear
Quick Start Guide
When power indicate lights up, exit the stick mode switch.
Choose MODE 1、MODE 2
ＭＯＤＥ １
2510
ＭＯＤＥ ２
Stick Mode Switch
Enter stick
Mode
switch
Exit stick
Mode
switch
1. Long press “ ” 3~5 sec
3. Long press “ ” 3~5 sec
2. Short press “ ”
ＭＯＤＥ ２
Rudder
Throttle Elevator
Aileron
MODE 2 is left-hand throttle
ＭＯＤＥ １
Elevator
Rudder
Throttle
Aileron
MODE 1 is right-hand throttle
When power indicate lights off, enter the stick mode switch.
power indicate lights
match the stick mode
IOC
IOC
IOC

-20-
W
V
U
W
V
U
W
V
U
W
V
U
14.5 Brushless ESC and Brushless Motor connection diagram
Brushless
ESC
Brushless
motor(CCW)
Brushless
motor(CCW)
Brushless
ESC
Brushless
ESC
Brushless
ESC
Brushless
motor(CW)
Brushless
motor(CW)
Head
Front
Attention:
The red, blue and black wires of the brushless motors must be soldering to the brushless ESC
according to the illustration.
14.4 Introduction for DEVO-RX715 receiver
Video
Video
DEVO F18 Remote Controller customize Fixed ID
Long-press “ ” button for 3-5 seconds, when the “drop” sound
to set the fixed ID. (for the first time to set fixed ID code, Battery Level indicator flashes
from left to right and then all the light solid.)
Long-press “ ” button 3-5 seconds again, when the “drop drop” sound to clear the fixed ID.
Flexible flat cable connection
The metal surface of flexible flat
cable plug should be inserted
upward to receiver port properly.
The metal surface of flexible flat cable
plug should be inserted downward to
power board port properly.
Port introduction
1. Idle port: Not used
2. Connection port: used to connect flexible flat cable
Quick Start Guide