wallas 4430 Manual

604398.ai 1 3.11.2011 13:38:19
4430
Remote Control System
en Installation, operation and service instructions

en
Contents
27 Technical information
27 Important notice
27 Package contents
28 Introduction
28 Operating
28 Technical information
29 Quick guide
30 Installation
30 General information
30 Subscriptions and SIM cards
30 Prepare the SIM card
31 Installing the SIM card
31 Installing the GSM aerial
31 Connecting of heaters 22 Dt, 30 Dt, 40 Dt, 26CC and 40CC
32 Connecting of heaters 1800 t and 2400 t
32 Connecting to the heater’s control panel
33 Relays
33 Data input
33 Power source
34 Preparing for start-up
34 Starting
34 GSM signals
35 Operation
35 Remote control via a web browser
35 Supported browsers
35 Registration
37 Settings
37 Heater settings
40 Panel settings
41 User settings
42 Use
43 Starting and stopping the heater
43 Adjusting heater temperature
44 Remote control by text messages
44 Controls
44 Control commands
44 “W” – Wallas heater control
45 Other commands
45 “S” status
45 Connections for a Wallas heater
45 Frequently Asked Questions
46 Resetting the factory settings (Reset)
47 Maintenance
47 Maintenance
47 Waste Electrical and Electronic Equipment
48 Disclaimer
48 Limited Warranty
D90020
- 2 -
4430
490538

4430
en
Technical information
Fastening screw 4,2 x 132 pcs
GSM/GPRS remote control
GSM/GPRS remote control aerial
Accessory bag
Connection cable
Mounting bracket, black
1 pcs
1 pcs
1 pcs
1 pcs
1 pcs
Installation, operation and maintenance instructions1 pcs
Package contents
Important notice
•Please read the instruction manual carefully.
•Make sure to observe all the warnings.
•Do not expose the unit to water or humidity.
•Clean the unit by wiping carefully with a dry cloth.
•Observe the installation instructions.
•Only use accessories, which have been recommended by Wallas-Marin Oy.
•Do not open the unit or try to repair it when any malfunction occurs. All repairs
must be performed by an authorised service provider. Additional information is
available from the equipment dealer.
DO NOT expose the unit to water or keep it in a humid room.
Water and other liquids can cause malfunctions. The warranty does
not cover such damages. The unit is intended for use indoors, and in
a dry environment.
Do not open the unit in the case of a malfunction. This will invalidate
the warranty.
The unit is remote-controlled and functions in a GSM and GPRS
network. The unit can be used if it is installed in an area with GSM
network coverage.
D80081
- 27 -
4430
490538

-20 - +40 °C
-30 - +50 °C
20 x 106 x 60 mm
5 A, 50 V
80 g
< 93 % RH
300-8011V16
en
Technical information
Introduction
The remote starter 4430 is intended for communicating data through a GPRS
network. The unit is intended for remote controlling of heating devices. The unit
can be used for starting and stopping the heater, for adjusting thermostat settings
(temperature), and for monitoring accumulator voltage and the temperature of the
premises being heated. Typical areas of application are ON/OFF switching of boat
and cottage heaters, and controlling of temperature and operating voltage. The
unit is controlled remotely by a PC via the most generally used web browsers, or
by smart phones. In an area with the GPRS network coverage the unit can also be
controlled by text messages in a GSM network.
Operating
The unit is controlled by a web browser programme (GPRS), or by text messages
(GSM). Controlling of the heater on a web browser the heater takes place in the
same way as in the control panel of the heater. In addition to signal lamps the vir-
tual panel on the browser displays the accumulator voltage and the room tempera-
ture (°C / F). By enquiring status data outside the GPRS network information about
all settings are communicated in a clear text message. The return text message is
in English.
In order to communicate data the remote starter requires at least GSM network
coverage. If the network coverage is poor we recommend using an external aerial.
The strength of the signal is displayed by the LED lights of the remote starter.
Green light means good signal, red lights means poor signal, and if there is no
signalthelightisoff.TheLEDlightashesonceeveryca7seconds.Ifatextcom-
mand is received the LED light stays green for 1–2 seconds.
Type
Average: 20 mA, 12 V DC
Relays: Each for 32 mA, 12 V DC
GSM with a direct MMCX connector
Class 4 (2 W), 850 / 900 MHz
Class 1 (1 W), 1800 / 1900 MHz
Operating voltage
Operating temperature
Maintenance temperature
Power consumption
Measurements
Weight
Aerial
Case
Relay
Humidity
Power
Technical information
push/push typeSIM card
Four frequency GSM / GPRS modem
(850, 900, 1800 and 1900 MHZ)
GSM / GPRS modem
7.5 -15.0 V DC
At least 1 A, operating output at least 1 W
IP class: IP20
D80071
- 28 -
4430
490538

en
Quick guide
1. Switch off the main power from the heater (disconnect the
accumulator cable)
2. On web page remote.wallas. check that the SIM card opera-
tor is included in the tested operator list.
3. Check that the PIN code request of the SIM card is disabled.
If necessary, disable it.
4. Install the SIM card in the remote control
5. Connect the remote control to the heater’s operating switch
GSM aerial interface
6. Install and connect the aerial
7. Switch of the heater’s main power
8. Ensure that the green LED light starts ashing with 7 sec
intervals
9. Register as a user on the web page remote.wallas. by using
the instructions on the screen
10.Save the control page as a bookmark (ask to conrm your
password), this facilitates the use of the remote control
D30081
- 29 -
4430
490538

1 2 3
5
4
en
Installation
General information
1) Data communication serial port
2) Power supply input (heaters 1800 t and 2400 t)
3) Relay output
4) Buttons and the LED light relays activation on the spot.
5) LED light indicating the GSM signal status.
Subscriptions and SIM cards
All data communication takes place in a GSM/GPRS network. In order to communi-
cate with the unit it is required to install a SIM card in it. The unit accepts SIM cards
of different operators, the list of approved/tested operators is available on the web
page remote.wallas.. Ask the unit dealer for more information concerning suitable
SIM cards, since there is a number of different SIM cards available.
Note:
It is advisable to get a monthly charged SIM card with data transmission features
for your unit.
If you use prepaid SIM cards do not forget to reload them, when the balance is
about to run out. 4430 does not function properly if the SIM card is not used cor-
rectly.
Prepare the SIM card
4430 requires the SIM card’s PIN code request to be OFF.
Deactivating the PIN code request feature.
1. Install the SIM card in the GSM phone.
2. Activate the phone and enter the PIN code.
3. Go to the security settings of the phone and disable the PIN code request fea-
ture. See more detailed instructions in the GSM phone’s user manual.
In some SIM cards the PIN code request feature is not activated, which means that
the card is ready for use.
D10241
- 30 -
4430
490538

TXU
RXI
GND
T1
T2
GND
l1
l2
S
GND
+12V
GND
R1
R2
R3
R4
Installation en
Installing the SIM card
1. Make sure that 4430 has not been connected to the operating switch through a
cable.
2. Placethecardinthepositionshownonthegurebelow.
GSM aerial interface
3. Push the SIM card into the card slot. A click indicates that the card has been
locked in place.
To remove the SIM card push it inwards and it springs up from the SIM card slot.
Installing the GSM aerial
Try to position the aerial vertically as high as possible.
Note that the aerial MUST NOT be mounted directly on a metal surface or near
metal objects. These can interfere with GSM signals. GSM aerials covering all the
four frequency areas with MMCX connector can be used as aerials.
Connecting of heaters 22 Dt, 30 Dt, 40 Dt, 26CC and 40CC
The cables are pre-connected to the connectors at the manufacturer’s plant.
Connect the connectors to the 4430unitasshownonthegure.
Note that the 4430 unit gets its operating voltage from the heater’s control panel,
no separate power supply is required.
White Green
Yellow
Brown
D10241
- 31 -
4430
490538

TXU
RXI
GND
T1
T2
GND
l1
l2
S
GND
+12V
GND
R1
R2
R3
R4
Installation en
White Green
Yellow Red
Black
BATTERY
Shield the free cable end to
prevent short circuits
Connecting of heaters 1800 t and 2400 t
With the heaters 1800 t and 2400 t the operating switch turns on 8V voltage, which
runs the 4430 unit, but the voltage reading on the display is incorrect (8V). It is ad-
visable to take the power for these units directly from the accumulator via a sepa-
rate fuse, in which case the reading on the display will be correct.
The power cable must have
at least a 1 A fuse
Connecting to the heater’s control panel
D10241
- 32 -
4430
490538

Installation en
Relays
4430 has 2 zero-voltage relays. These can only be controlled by text messages or
with two buttons on the equipment. Relay outputs are marked as R1 and R2.
Data input
4430 has 2 data interfaces, TXU and RXI. They are intended only for connecting to
an external Wallas equipment using the cable included in the delivery.
Power source
A Wallas heater functions as a power source in the following equipment 22 Dt, 30
Dt, 40 Dt, 26CC and 40CC.
When heaters 1800 t and 2400 t, are used, it is advisable to connect the 4430 unit
directly to the same 12V accumulator, which is used by the heater.
Do not switch the power on (connect the power cable to the heater)
before all connections have been made.
When the power is connected to the heater it is prohibited to touch
(disconnect or connect) any 4430 connectors.
D10241
- 33 -
4430
490538

Installation en
Preparing for start-up
Starting
After all the connections have been made and the SIM card (with disabled PIN
code) has been installed, the 4430 unit may be started.
Switch on the heater’s main power / heaters power cable back, and monitor the
LED light on the remote control.
• During the starting stage the LED light is red, and after a while its colour turns
greenanditstartsashinguniformlywith7secondintervals.
• IftheSIMcardismissingoriftheSIMcardisfaulty,theLEDlightstartsash-
ing green after a couple of seconds. In this case check the PIN code and
ensure that the card is well in its place.
• Errorsaresignalledbytwoshortrepetitiveashes(twoashes–apause–two
ashes…)(e.g.ifthePINcoderequesthasnotbeendisabled).
• AredashingLEDlightsignalsofanerrorintheself-checkingprogram.
Please contact the equipment dealer.
GSM signals
The strength of the GSM signal can be determined by the LED light of the signal.
TheLEDlightasheswiththeintervalofca7seconds.
• A green light means that the signal is good.
• A red light means that the signal is weaker/ poor.
• No light means that there is no signal. In this case the unit cannot be remotely
controlled.
In the two latter cases try to move the GSM aerial to improve the signal. One of the
options is to purchase an external aerial. GSM aerials covering all the four frequen-
cy areas with MMCX connector can be used as aerials.
Boat trips between several countries:
If you intend to take boat trips to more than one country, please
check whether the SIM card features are suited for the local operator
(Roaming)
Please note that applicable charges differ considerably under differ-
ent Roaming agreements!
If necessary remove the SIM card from the unit to prevent excessively
high charges.
If you intend to stay abroad for a long time, it is advisable to pur-
chase a SIM card of a local operator, if you intend to use the 4430
remote starter.
D10241
- 34 -
4430
490538