Walton 01OSBP0602 User manual

NATURAL MOVEMENT OF TIMBER THROUGHOUT THE SEASON
Timber is a natural material and will, during the year pick up moisture in damp periods and dry out during hot spells. There will be constant expansion
and contraction of the timbers which will be particularly noticeable during the dry periods as the boards will shrink, this is why all buildings have
slight tolerances built into them.
BUILDING A BASE
When thinking about where the building and base is going to be constructed: Ensure that there will be access to all sides for maintenance work and
annual treatment.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base dimensions, The base should be slightly
smaller than the external measurement of the building, i.e. the cladding should overlap the base, creating a run o for water. It is also recommended
that the oor be at least 25mm above the surrounding ground level to avoid ooding.
PLEASE READ INSTRUCTIONS CAREFULLY.
For ease of assembly, it is
advisable to pilot drill all
screw holes and ensure all
screw heads are countersunk.
WINTER = HIGH MOISTURE = EXPANSION
SUMMER = LOW MOISTURE = CONTRACTION
Drill
2mm bit
x2
Dimensions
Height = 1960mm
Width = 1786mm
Depth = 797mm
01OSBP0602/01OVLP0602V1
Before you start...
All buildings including the underside of the floor must be treated with a good quality waterproof
preservative or treatment prior to or during assembly, and retreated annually.
Preservative/treatments are available in a choice of colours and is left to the customers preference.
Tools required for installation (not supplied)
Screwdriver (cross point),Stanley knife, wood saw
and step ladders.
For Assistance Please Contact Customer Care on 01636880514
This building should be erected by two people.
*Shiplap version
shown in illustrations
Whilst all products manufactured at Walton Garden Buildings Limited are made to the highest standards of Safety and in the case of
childrens products independently tested to EN71 level,Walton Garden Buildings Limited cannot accept responsibility for your safety whilst
erecting or using this product.
Gable x2
(Shiplap only)
Gable x2
(Overlap only)
Front Panel Rear Panel
Floor Panel
Door x2
Gable tops
(Shiplap only)
Felt
Roof Panel
Eave Framing-1786mm
4x Corner Trim -1759mm (Shiplap only)
Rear Fascia -1810mm
2x Side Fascia -830mm
2x Corner Trim -1818mm (Overlap only)
2x Corner Trim -1918mm (Overlap only)
2x Door block -140mm
Iron mongery & Nail Bag Contents
Door hinge x4
30mm Screw x80
50mm Screw x30
40mm Screw x15
10mm Felt Tacks x80
Turn Key x2 Pad bolt
Please retain product label and instructions for future reference

Assembly
Step 1
Remove transportation blocks
from the bottom of each panel
before beginning assembly.
Each Panel should have two
blocks.
Step 2
Place floor on a firm and
level base, ensure base has
suitable drainage free from
areas where standing water
can collect. (see front page
on base requirements).
Step 3
Do not secure the building
to the floor until the roof is
fitted. Fix the panels onto
the floor using 50mm
screws in alignment with
the floor joists
Fix the corners with 3x
50mm screw a shown in
diagram.
Position the panels so there is
equal spacing between the
floor and cladding on all 4 sides
9 x 50mm screws
Step 4
Fix door gable and front panel
using same method shown in
step 3.
15 x 50mm screws
Step 5
Place the Gable Top onto the
plain gable, ensuring the
cladding and framing on either
side is flush with gable. Fix with
2x30mm screws as shown in
diagram.
4 x 30mm screws
*Shiplap Only
*Shiplap Only

Step 6
Fix Eave framing to edge of
Roof sheet using 4x30mm
screws.
Place roof into position ensuring
the eave frame fits butt against
the panel cladding. Fix using
10x30mm screws as shown in
diagram.
14 x 30mm screws
*Fix eave frame to
roof sheet first
Step 7
Lay sheet of felt onto roof as
shown in diagram ensuring
there is a 50mm overhang
around the sides.
Fix using felt tacks at 100mm
intervals
80 x Felt Tacks
100mm
intervals
50mm
Overhang
1mm
30mm
screws
44 x 30mm screws
Fix hinges to the doors with
30mm screws ensuring the
screws are located into the door
framing.
Position each door on to the
building leaving a 2mm gap in
between doors and building. Fix
the door to the building with
30mm screws.
Fix pad bolt with 6x30mm screws
to horizontal door brace.
Then fix the pad bolt retainer to
the opposite door framing using
4x30mm screws.
Step 8
*Fix door block and turn key to
top and bottom of door with bolt
retainer fitted, using 30mm
screws.
Step 9
Use 3x30mm screws to fix
each cover trim.
12 x 30mm screws
9 x 40mm screws
Step 10
Fit fascia boards to
building using 3x40mm
screws per board as shown
in diagram.
Pre drill holes before hand,
making sure screws go into
the framing.