Wanderer WA1025GD User manual

PARTS LIST
#Part
1Knob
2Spindle
3Spindle ‘O’ rings
4Stainless Steel Drip
Tray
5Trivet
6Burner Jet
7Burner
8Windshield
9Grill tray & rack
10 Grill burner
11 Piezo Igniter
12 Flexible hose
assembly
FITTING & USAGE INSTRUCTIONS
• Remove from the carton and discard all packaging material.
• Place on a level (horizontal) surface.
• Open lid, attach side supports to secure the stove, open windshields and lock them in place.
• Lift the trivet, remove the hose and connect it to the inlet connection. Tighten firmly by hand.
• Make sure the valves are turned off on both the appliance and gas cylinder prior to connecting
or removing the stove.
• Firmly fasten the hose to the gas cylinder control valve.
• Ensure the controls on the stove are in the OFF position. Turn the gas cylinder control valve on.
Check for leaks at all gas joints by applying a soapy water solution.
• If a leak is detected by observing a stream of bubbles or by the distinct gas odour, turn off the
cylinder valve and do not use the appliance until the source of the leak has been successfully
fixed. Re-test for leaks each time before igniting the appliance.
• To light grill, hold a match next to the grill burner and turn on (anti-clockwise) the middle
control knob. Ensure both sides of the burner are alight. When lit adjust the burner to suit.
LIGHT BURNERS VIA PIEZO ELECTRIC IGNITION
• To light the grill or hob burners, open the control valve in front of the burner you wish to ignite,
then immediately turn the piezo ignitor knob until the burner is alight. If the burner fails to
light, turn off the gas supply and wait 5 minutes before reattempting to ignite the burner.
LIGHT BURNERS VIA MANUAL IGNITION
• To light the hob burners place a lit match beside the burner and turn the control in front of the
required burner anti clockwise. If any burner fails to light, turn off the gas supply and wait 5
minutes before reattempting to ignite the burner.
• Use the stove control knobs to obtain the desired heat setting by turning
anti-clockwise to increase the heat and clockwise to decrease the heat and turn off.
• To extinguish turn off the gas at the cylinder control valve. Allow all residual gas
to disperse or burn off before turning the appliance controls to the off position.
• When alight, the gas stove should never be left unsupervised.
• Do not move the appliance during operation.
• During use, parts of the stove can reach high temperatures. After use, allow stove to cool
before handling.
• The burner extinguishing during use may indicate that the gas cylinder has run out of gas. If
this occurs replace the empty gas cylinder with a full gas cylinder and attempt to reignite the
burners. If the burners do not ignite there may be a blockage in the injectors or the flexible
hose. Replace the components as required to make the appliance serviceable or take the
appliance to a service centre to be professionally repaired.
• To ensure maximum life from your appliance it should always be stored in a dry place, out of
direct sunlight.
• To check if gas cylinder contains gas, disconnect from the cooker, then hold upright and
shake from side to side. If you can feel or hear liquid movement from within the cylinder, it
contains gas.
• Before each use, check primary air openings and clear blockages.
• Abnormal operation which may require service can be identified by black sooting of cooking
utensils, or an irregular burner flame which is yellow or unstable.
• After use, turn the gas cylinder valve off, wait for the flame to go out, then turn the appliance
control valve(s) off.
1
23
6
7
8
9
10
11
12
4
5
REPLACING JET (INJECTOR)
IF THE BURNER STOPS WORKING, THE JET MAY BE BLOCKED.
• The jets may require periodic cleaning or replacing if they become blocked. If this
occurs, you can remove the jet and clear the blockage or simply replace the jet with
the spare jet packed with this stove.
• You will need a screw driver and a spanner to complete this task. Use these tools
to remove the hinge screws and nuts, then rotate the top and remove the burner
mounting screws. Slide burner off the brass valve for access to the jet.
• Top burner jet size is 0.20.
• Grill burner jet size is 0.11.
• Do not modify, alter or fit incorrect jet sizes to the burners.
• To clean the jet, blow out the blockage, or wash jet in white spirits. Do not use
needles or pins to clean the jet because this could damage the jet making the
gas stove dangerous.
• Conduct a gas leakage test of all connections as described in this instruction manual
after jet replacement. DO NOT use this stove unless the appliance is gas tight (there
are no gas leaks).
REPLACING ‘O’ RINGS
• Gas leaking from the front of the control indicates that the “O” Rings MUST be replaced
before igniting the appliance.
• Turn off all controls on the appliance as well as the cylinder.
• Disconnect the flexible hose from the appliance and the cylinder.
• Remove the control knob by pulling forward away from the stove.
• Remove the control locking nut located directly behind the control knob by rotating in
an anti-clockwise direction.
• Remove the control spindle by rotating in an anti-clockwise direction.
• Remove the damaged “O” Rings from the spindle and replace with new ones.
• Reassemble in the opposite order of disassembly. Note: Push in spindle before turning
clockwise.
• “O” Ring (Spindle) Service Pack AN1992.
MAINTENANCE
This appliance does not require regular maintenance, however each time before use it
should be verified that it is in a suitable working condition. If any faults are detected the
appliance is not to be used until they have been rectified.
SPECIFICATIONS
Consumption Rate: 230g/h per burner, 70g/h grill.
For use with LPG.
Injector size: Australia Burner 0.20mm Jet, Grill 0.11mm Jet.
This appliance shall only be used with a propane gas cylinder certified to Australian Standard
AS2030. IT MAY BE HAZARDOUS TO ATTEMPT TO FIT OTHER TYPES OF GAS CYLINDERS.
Operating Pressure: Vapour Pressure.

2 BURNER DELUXE STOVE WITH GRILL
ASSEMBLY AND OPERATING INSTRUCTIONS
• Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury
• or death. Read these instructions for use carefully.
• WARNING: Accessible parts may be very hot. Keep young children away at all times.
• Familiarise yourself with the appliance before connecting it to its gas container. Keep these instructions
for future reference.
WARNINGS
• ONLY USE IN WELL VENTILATED AREAS, USE OUTDOORS ONLY, NEVER USE
INDOORS.
• CARBON MONOXIDE HAZARD – THIS APPLIANCE CAN PRODUCE CARBON
MONOXIDE WHICH HAS NO ODOUR. USING IT IN AN ENCLOSED SPACE (FOR
EXAMPLE CARAVAN, TENT, CAR, MOBILE HOME, DOMESTIC RESIDENCE) MAY
CAUSE DEATH.
• Caution: Accessible parts may be very hot. Keep young children away.
• Do not modify this appliance.
• Check that the seals between the appliance and the gas cylinder are in place
and in good condition before connecting to the gas cylinder.
• Do not use this appliance if it has damaged or worn seals.
• Do not use this appliance if it is leaking, damaged or does not operate
properly.
• Stove must be completely extinguished before disconnecting from cylinder.
• If there is a leak on your appliance (smell of gas), immediately attempt to
turn off the cylinder valve. DO NOT LIGHT THE APPLIANCE. Remove the
appliance to a well ventilated location away from any ignition source. Only
check for leaks outdoors using soapy water. Do not try to detect leaks using
a flame.
• Never lift the appliance while it is in use.
• This appliance shall be used away from flammable materials.
• This appliance is not to be used within 1200mm from any combustible
materials (i.e. 1200mm clearance in all horizontal or vertical directions).
• Wipe with a moist cloth. Do not use abrasive cleaning products or chemicals.
• This appliance must only be serviced by an authorised person.
• Gas cylinders are to be changed in a well ventilated area, outside, away from
people and from ignition sources such as naked flames, pilot lights, electric
heaters/equipment.
• Only use the hose assembly supplied with the appliance for direct
connection to the cylinder – DO NOT USE ADAPTORS. When necessary only
use genuine replacement hose not exceeding 1500mm in length.
• When not in use store the appliance in the folded position in a well
ventilated dry location.
• Avoid twisting or kinking the flexible hose.
• This appliance shall only be used in an above ground open air situation with
natural ventilation, without stagnant areas, where gas leakage and products
from combustion are readily dispersed by wind and natural convection.
• When not in use store the gas cylinder outdoors in a well ventilated area out
of reach of children. Any indoor storage shall comply with AS/NZS 1596.
• Store this appliance when not in use disconnected from the gas cylinder.
Open side at least
25% of total wall area
Open side at least
25% of total wall area
30% or more in total
of the remaining wall area
is open and unrestricted
30% or more in total
of the remaining wall area
is open and unrestricted
A
or B
Minimum Enclosed Area Ventilation
PLACEMENT
The figures below are diagrammatical representations of suitable outdoor areas in which this
appliance can be used.
WARNING: FOR OUTDOOR USE ONLY
WA1025GD
AGA APPROVAL NO: 7095
AGA
approval
No: 7095
Australian Gas Association
WA1025GD - 16-09-08-V1