Watchguard 4RE 2007 User manual
WatchGuard Video ‐ Proprietary
WGD00080‐005Re
v
C Page 1 o
f
5
4RE2007‐2014TahoeBracketInstallationManual
Parts included with Bracket:
1 – WGAP01459-001- Bracket 4RE,
Display, Chevy Tahoe, 2007+
Screw Kit (WGP01459-HDW):
(2) – 10x3/4” Hex (5/16” head) Self Drilling Screw (WGP01546-001)
(2) – #8-32 1 ½ " Silver Phillips Machine Screws (WGP01545-002)
**(2) – #8 x 1 -1/4" Black Phillips Self Drilling Screws (not used) (WGP01552-002)
Parts needed from 4RE system (in separate box):
Touch Display Screen
HDMI cable
RAM Mount Kit (WGA00420)
ToolsRequired:
Philips Head #2 Screwdriver
Flat Blade Screwdriver
Torx 15 screw driver
10 mm socket wrench (for removing A Pillar handle)
5/16” Socket wrench
1/16” Allen Wrench
**Extra Screws not used in this installation
5/32
Allen
Screws #8 x 1 and 1/4"
Self Drilling
Screws #8-32 1 ½”
Screws
5/16
Hex
Screws
WatchGuard Video ‐ Proprietary
WGD00080‐005Re
v
C Page 2 o
f
5
BeforeInstallation
Before installing the bracket in the vehicle, ensure there are no missing or damaged parts from
the box. If there are any missing or damaged parts, please contact:
Customer Service at 866-384-8567
*Note: For more detailed instructions on installing the complete 4RE system, please refer the
4RE Vehicle Installation Manual.
RoutingtheHDMItominiHDMIcable
Before attaching the bracket route the mini HDMI (HDMI to mini HDMI) connector to Overhead
center console. The HDMI cable is typically routed through the headliner down the passenger A
Pillar. To access the A Pillar, the installer will need to unscrew the post handle (if applicable).
The 2 bolts are 10mm socket. Remove the bolts and then remove the cover to access the hole
to route the HDMI cable to the 4RE system.
*Warning: When pulling off the cover for the A Pillar, be aware of the airbag accidentally
deploying.
MountingtheOverheadConsoleBracket
After the cable is routed (HDMI mini to the Overhead Center Console and HDMI to the 4RE) get
a flat head screw driver.
Carefully remove the plastic light cover with a flat head screw driver as pictured below:
WatchGuard Video ‐ Proprietary
WGD00080‐005Re
v
C Page 3 o
f
5
After the light cover is removed, locate and remove the (2) Torx 15 screw holding up the
Overhead Console to the ceiling of the vehicle. See picture below:
Once the screws are removed, the Overhead console will stay in place until slight pressure is
applied to pull the console down. Place one or two fingers on the corner of the console to pull it
down.
Once the console is pulled down, disconnect the cable to the power the overhead lights. Next
set aside the console with the plastic light cover, because it will be put back in place after the
installation is complete.
There will be another small factory bracket attached. Remove that small bracket with the Torx
15 screw driver and keep the screws, because they will be used to mount the bracket to the roof
of the vehicle.
WatchGuard Video ‐ Proprietary
WGD00080‐005Re
v
C Page 4 o
f
5
The Console should now look like the following:
Next line up the factory holes with the holes on the 4RE Touch-Display Bracket. Then use the
Torx 20 screws to attach the bracket to the roof of the vehicle. For added support you can drill
(2)
10x3/4” Hex (5/16” head) screws in the (2) inner predrilled holes noted with the arrows.
After the bracket is securely mounted, plug in the power to the lights and put the overhead
console in place. Also route the mini HDMI cable through the top of the overhead console
leaving enough room for the display to rotate unheeded (typically 5-6 inches). Then use the 2
#8-32 x 1- 1/2” long machines screws where the red arrows indicate to attach the overhead
console to the bracket underneath.
WatchGuard Video ‐ Proprietary
WGD00080‐005Re
v
C Page 5 o
f
5
Next put factory plastic light cover back on to cover the screws and light fixtures. After the
overhead console is put back together attach the RAM ball mount (not included with bracket)
with the (2) – 10x3/4” Allen (5/32”) screws to the section of the bracket protruding from the
overheadconsole.
The final step is to connect the mini HDMI cable to the back of the display unit.
1.
Remove the buttonhead screw and cover with 1/16th Allen wrench.
2.
Attach the mini HDMI cable
3.
Put the cover back on
4.
Attach RAM mount bracket using (4) Buttonhead #4 - 40x.250”.
5.
Attach RAM ball bracket to RAM mount bracket using (2) - 10X32 1/2” screws.
6.
Attach the Display to the RAM coupler, orient to suit and tighten the coupler to hold.
This manual suits for next models
7
Table of contents
