WaterAce WA33FPM User manual

Owner’s Manual
Waterfall
Fountain Pumps
General Safety . . . . . . . . . . . . . . . . . . . . 2
Specications. . . . . . . . . . . . . . . . . . . . . 3
Installation. . . . . . . . . . . . . . . . . . . . 4 & 5
Troubleshooting . . . . . . . . . . . . . . . . . . . 6
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . 7
TABLE OF CONTENTS
WA50FPW WA33FPM

A sump pump is an electrical device designed to
operate in inherently wet environments.
ALWAYS USE EXTREME CAUTION
when installing or maintaining this product!
Need Help: Call 1-877-326-3561 for assistance;
Do Not Return to Store
Important Safety Instructions
Carefully read and follow all safety
instructions in this manual and on pump.
SAVE THESE INSTRUCTIONS – This manual
contains important instructions that should be
followed during installation, operation, and
maintenance of the product.
Save this manual for future reference.
Safety Labels
This is the safety alert symbol. When you
see this symbol on your pump or in this manual,
look for one of the following signal words and be
alert to the potential for personal injury!
Indicates a hazard which, if
not avoided, will result in death or serious injury.
Indicates a hazard which,
if not avoided, could result in death or serious
injury.
Indicates a hazard which, if
not avoided, could result in minor or moderate
injury.
NOTICE indicates practices not related to
personal injury.
Keep safety labels in good condition. Replace
missing or damaged safety labels.
General Safety
Risk of burns. Do not
touch an operating motor. Motors are de-
signed to operate at high temperatures. To
avoid burns when servicing pump, allow it to
cool for 20 minutes after shut-down before
handling.
Do not allow pump or any system compo-
nent to freeze. To do so will void warranty.
Pump water only with this pump.
Periodically inspect pump and system com-
ponents.
Wear safety glasses at all times when work-
ing on pumps.
Risk of explosion. Pump
body may explode if used as a booster
pump.
2
GENERAL SAFETY
STOP Before you start

3
APPLICATIONS
Designed for use as a Waterfall/Fountain Pump. Other uses include pumping water from cisterns and sumps.
SPECIFICATIONS & PERFORMANCE
Capacity Cord
Model HP Volt Ph Amps (GPH at 0’) Max Head Construction Impeller Length
WA33FPM 1/3 115 1 2.8 1500 16 Stainless Steel Stainless Steel 15’
WA33FPW 1/3 115 1 2.8 1500 16 Stainless Steel Stainless Steel 15’
WA50FPM 1/2 115 1 4.1 2400 24 Stainless Steel Stainless Steel 15’
WA50FPW 1/2 115 1 4.1 2400 24 Stainless Steel Stainless Steel 15’
WA75FPM 3/4 115 1 6.4 3300 26 Stainless Steel Stainless Steel 15’
WA75FPW 3/4 115 1 6.4 3300 26 Stainless Steel Stainless Steel 15’
12"
(305)
7"
(178)
3-1/2"
(89)
1-1/4 NPT
7"
(178)
7"
(178)
3-1/2"
(89)
8-1/2"
(216)
15-11/16
"
(399)
ON
OFF
1-7/8"
(48)
10-1/2"
(266)
7"
(178)
1-7/8"
(48)
3-1/2"
(89)
7"
(178
1-1/4 NPT
7"
(178)
7"
(178
)
3-1/2"
(89)
8-1/2"
(216)
15-11/16"
(399)
12"
(305)
7"
(178)
3-1/2"
(89)
1-1/4 NPT
7"
(178)
7"
(178
)
3-1/2"
(89)
8-1/2"
(216)
15-11/16"
(399)
ON
OFF
1-7/8"
(48)
SEP75W SEP33M

4
(b) Cutting o the ground pin or using an
adapter tting.
(c) Working on pump or switch while
plugged in.
(d) Removing motor housing, unscrewing
impeller, or otherwise removing impeller seal.
(e) Running the pump continuously.
(f) Pumping chemicals or corrosive liquids.
 (g)Pumpinggasolineorotherammableliquids
8.PlasticPVCpipecanbeinstalledinthe 
outlet piping. Drain hose, galvanized steel
 orcopperpipemaybeusedifdesired. 
 Allpipingmustbecleanandfreeofall 
foreign matter to prevent clogging.
Verify that the voltage and
frequency of the pump shown
onthenameplatecorrespondstothoseavailableon
the mains. The installer must make sure that the
electric system is grounded in accordance with code.
• Foroutdooruseitisnecessarytousecablewith
a lengthofatleast8’.Theplugandconnection
 shouldbeprotectedfromwatersplashes.Before
using the pump, always inspect it visually
 (especiallypowercableandplug)
• Do not use pump if it is damaged
• Ifthepumpisdamaged,haveitinspectedbyan
authorized service center.
• Make sure that electric connections are protected
 fromooding.Protecttheplugandthepower
 cablefromheatorshapeedges.
     Thepowercablemustbere
     placedbyqualiedpersonnel
only.Grounding:Theplugofthepowercablehasa
doublegroundingcontact,sothatgroundingcanbe
performedbysimplyinsertingtheplug.
This pump series has a built in thermal protection
switch. The pump stops if an overload condition
occurs. The motor restarts automatically after it has
cooled down.
INSTALLATION
ELECTRICAL WIRE CONNECTION
OVERLOAD PROTECTION
Do not work on pump until power is unplugged.
Do not cut off ground pin or use an adapter
tting.
Do not use an extension cord.
Thepumppowercordshouldbeconnectedtoa
separately fused, grounded line with a minimum
capacityof15amps.Itcanbeconnectedtonon-
fusebreakerattherecommendedamperes.
1.Beforeinstallingorservicingthispump,be 
certain pump source is disconnected.
2. Installation and electrical wiring must adhere
 tostateandlocalcodesandmustbe 
 completedbeforeprimingpump.Check 
appropriate community agencies, or contact
local electrical and pump professionals.
3.Callanelectricianwhenindoubt.Pump 
 shouldbeconnectedtoaseparate15 
 ampcircuitbreakeror15ampfuseblock. 
Note that plugging into existing outlets may
cause low voltage at motor. This could cause
 blownfuses,trippingofmotoroverloador 
 burnedoutmotor.
4. A permanent ground connection from pump
 tothegroundingbarattheservicepanelis 
mandatory. These sump pumps come with a
 groundingconductorandagrounding-type 
attachment plug. Do not connect pump to
a power supply until permanently grounded.
For maximum safety, connect pump to a circuit
equipped with a fault interrupter device when
 positioningthepump’sgroundingwire.
5. Voltage of power supply must match the
voltage of the pump.
6. Before installing pump, clear sump basin of
any water, debris or sediment.
Sump basin must be vented
in accordance with local
plumbing codes. These Sump pumps are not
designed for and CANNOT be installed in loca-
tions classied as hazardous.
7. The following may cause severe damage to
pump and will void the warranty.
(a) Using an extension cord.
4

5
STEP 1:
Install pump on a hard level surface o of the bottom of the basin. Be sure that the
pump is clear of small rocks, mud and other debris. Putting a block or brick under
pump is recommended. See Fig. 1 above.
STEP 2:
Protect the power cord from damage. A uncovered cord should be checked
routinely for any damage or deterioration. DO NOT operate the pump if cord is
damaged in any way.
STEP 3:
Choose from the included 1-1/4” FNPT x 1-1/4” FNPT elbow and 1-1/4” MNPT x
1-1/2” FNPT adapter when attaching the tubing. See Fig. 2.
Fig 2
1-1/4” MNPT x 1-1/2” FNPT
1-1/4” FNPT x
1-1/4” FNPT
elbow
INSTALLATION
CAUTION:
Check local codes before installing pump.
Fig 1: Garden Pond
and Waterfall
Installation
GFCI Outlet
Landscape
rocks
Power
Cord
Plastic Tubing
to waterfall
Plants and ground cover
work well to cover tubing
Place pump on
block to raise
o bottom of
basin

6
TROUBLESHOOTING CHECKLIST (Caution: shut off power to pump)
PROBLEMS
PUMPDOESNOTRUN
ANDMAKESHUMMING
SOUND
PUMPRUNSBUTDOES
NOTDELIVERWATER
PUMPRUNSAND
PUMPS
OUTSUMP,BUTDOES
NOTSTOP
PUMPRUNSBUTONLY
DELIVERSASMALL
AMOUNTOFWATER
FUSEBLOWSOR
CIRCUITBREAKER
TRIPSWHEN
PUMPSTARTS
MOTORRUNSFORA
SHORTTIME,THEN
STOPS
POSSIBLE CAUSES/SOLUTIONS
• Line circuit breaker is o, or fuse is blown or loose
• Water level in sump has not reached turn-on level as indicated in
installation drawing.
• Pump cord is not making contact in receptacle.
• Float is stuck. It should operate freely in basin.
• If all of the above are OK, then the motor could be malfunctioning.
• Check if valve is installed backwards.
Arrow on valve should point direction of ow
• Discharge shut-o valve (if used) may be closed.
• Impeller or volute openings are fully or partially clogged.
Remove pump and clean.
• Pump is air-locked. Start and stop several times by plugging and
unplugging cord. Check for clogged vent hole in pump case.
• Inlet holes in pump base are clogged. Remove pump and clean the
openings.
• Vertical pumping distance is too high. Reduce distance or change the
discharge ttings of the pump.
• Float is stuck in up position. Be sure oat operates freely in basin.
• Defective oat switch. Replace oat switch.
• Pump is air-locked. Start and stop several times by plugging in and
unplugging cord. Check for clogged vent hole in pump case.
• Vertical pumping distance is too high. Reduce distance or change the
discharge tting of the pump. Inlet holes in pump base are clogged.
Remove pump and clean the strainer and openings.
• Impeller or volute openings are fully or partially clogged.
Remove pump and clean.
• Pump impeller is partially clogged with tar or paint, causing motor to
run slow and overload. Remove pump and clean.
• Pump impeller is partially clogged causing motor to run slow and
overload. Remove pump and clean.
• Motor stator may be defective.
• Fuse size or circuit breaker may be too small. (must be 15 amps).
• Impeller or volute opening are fully or partially clogged.
Remove pump and clean .
• Inlet holes in pump base are clogged. Remove pump and clean the
openings.
• Pump impeller is partially clogged causing motor to run slow and
overload. Remove pump and clean.
• Motor stator may be defective.
• Impeller or volute openings are fully or partially clogged.
Remove pump and clean. Also clean the strainer if one is installed.
ELECTRICAL PRECAUTIONS
Before servicing a pump, always shut o the main power breaker and
then unplug the pump. Make sure you are not standing in water and are
wearing insulated protective sole shoes, under ooded conditions. Contact your local electric
company or a qualied licensed electrician for disconnecting electrical service prior to pump
removal

7
WARRANTY
Retain Original Purchase Receipt for Warranty Eligibility
Limited Warranty
Manufacturerwarrantstotheoriginalconsumerpurchaser(“Purchaser”or“You”)thatitsproductsarefreefromdefectsin
material and workmanship for a period of twelve (12) months from the date of the original consumer purchase. If, within
twelve(12)monthsfromtheoriginalconsumerpurchase,anysuchproductshallprovetobedefective,itshallberepaired
orreplacedatmanufacturer’soption,subjecttothetermsandconditionssetforthherein.Notethatthislimitedwarranty
applies to manufacturing defects only and not to ordinary wear and tear. All mechanical devices need periodic parts and
service to perform well. This limited warranty does not cover repair when normal use has exhausted the life of a part or
the equipment.
Theoriginalpurchasereceiptandproductwarrantyinformationlabelarerequiredtodeterminewarrantyeligibility.Eligibil-
ityisbasedonpurchasedateororiginalproduct–notthedateofreplacementunderwarranty.Thewarrantyislimitedto
repair or replacement of original purchased product only, not replacement product (i.e. one warranty replacement allowed
per purchase).
Purchaserpaysallremoval,installation,labor,shipping,andincidentalcharges.
Claimsmadeunderthiswarrantyshallbemadebyreturningtheproducttotheretailoutletwhereitwaspurchasedorto
thefactoryimmediatelyafterthediscoveryoranyallegeddefect.Manufacturerwillsubsequentlytakecorrectiveactionas
promptlyasreasonablypossible.Norequestsforservicewillbeacceptedifreceivedmorethan30daysafterthewarranty
expires.Warrantyisnottransferableanddoesnotapplytoproductsusedincommercial/rentalapplications.
General Terms and Conditions; Limitations of Remedies
Youmustpayalllaborandshippingchargesnecessarytoreplaceproductcoveredbythiswarranty.Thiswarrantydoes
notapplytothefollowing:(1)actsofGod;(2)productswhich,inmanufacturer’ssolejudgment,havebeensubjectto
negligence,abuse,accident,misapplication,tampering,oralteration;(3)failuresduetoimproperinstallation,operation,
maintenanceorstorage;(4)atypicalorunapprovedapplication,useorservice;(5)failurescausedbycorrosion,rustor
other foreign materials in the system, or operation at pressures in excess of recommended maximums.
Thiswarrantysetsforthmanufacturer’ssoleobligationandpurchaser’sexclusiveremedyfordefectiveproducts.
MANUFACTURERSHALLNOTBELIABLEFORANYCONSEQUENTIAL,INCIDENTAL,ORCONTINGENTDAMAGES
WHATSOEVER.THEFOREGOINGLIMITEDWARRANTIESAREEXCLUSIVEANDINLIEUOFALLOTHEREXPRESS
ANDIMPLIEDWARRANTIES,INCLUDINGBUTNOTLIMITEDTOIMPLIEDWARRANTIESOFMERCHANTABILITY
ANDFITNESSFORAPARTICULARPURPOSE.THEFOREGOINGLIMITEDWARRANTIESSHALLNOTEXTEND
BEYONDTHEDURATIONPROVIDEDHEREIN.
Somestatesdonotallowtheexclusionorlimitationofincidentalorconsequentialdamagesorlimitationsonhowlongan
impliedwarrantylasts,sotheabovelimitationsorexclusionsmaynotapplytoYou.ThiswarrantygivesYouspeciclegal
rightsandYoumayalsohaveotherrightswhichvaryfromstatetostate.

1899 Cottage Street
Ashland, Ohio 44805
Telephone: [phone]