Waterguard V21i User manual

Step by Step Installation….

1. Fit the valve assembly. Find a suitable location close to where the

water supply enters the property. Turn off the water supply and

drain. Select suitable pipe fittings. Cut the pipe to give the correct

gap for the valve Assembly, approximately 9-11”. Plumb in the

valve assembly. Tighten the pipe fittings. Turn on the water supply

and check for leaks. Re-lag the pipework. Do not over tighten or

overuse PTFE tape.

2. Fix controls to chosen area. The wireless remote display can be

located up to 10 meters away from the valve driver, ensure to

connect x 2 AAA batteries (see reverse for pairing info).

3. Wire the latching solenoid valve and flow sensor to the Home

controller:

•Red to V

•Black and Brown to C

•Blue to F

4. Where applicable, use 2 core flex cable to:

•Connect the intruder alarm to the ALARM IN terminal for

automatic guard switching.

•Connect the BMS or hardwire a Waterguard DataCom to the

ALARM OUT terminal.

•If the remote display is to be fitted over 10 meters from the

Home Controller it is recommended to hardwire the two

units. Use 2 core flex cable from the black hard wire terminal

on the Home Controller to the green 2 gang terminal on the

Remote display.

5. Connect power to the valve driver using the 12V power pack.

6. Connect 9V battery to the valve driver. DO NOT CONNECT THIS

BEFORE POWER.

Ensure to see the next page for set up.

ATTENTION…..

IT IS IMPORTANT TO STRICTLY FOLLOW THESE INSTRUCTIONS IN FULL. THE 3V LITHIUM BATTERY MUST ONLY BE CONNECTED AFTER

MAINS POWER. FAILURE TO DO THIS WILL RESULT IN SYSTEM FAILURE.

Water Leak Detection

Equipment

Waterguard Home -

Installation Guide V21I

IMPORTANT: PLEASE READ THIS GUIDE IN FULL BEFORE INSTALLING.

What you will have:

· 1 x Waterguard Home controller with rechargeable battery.

· 1 x Waterguard Home Remote Display with x 2 AAA batteries.

· 1 x Waterguard flow sensor

· 1 x Waterguard shut off valve

· 1 x 12V power pack OR 1 x 240V adapter

· 1 x pair push fit connectors (complete kit only)

What you will need:

· 2 Core Flex - PVC 2 Core Flat Flexible Cable (2192Y) min 0.75mm2 if

connecting to intruder alarm, BMS or Waterguard DataCom

· PTFE tape

· Valve assembly connectors (standard kit only)

· 2 x single pattress boxes

Success?

The LED on the Home controller will illuminate WHITE, followed by a single GREEN flash and BEEP, indicating that the unit has power and is operational

in HI GUARD mode.

The remote display will show 888 on the screen for a couple of seconds. If either are not as described, please call the office for technical support.

Test….

To check the correct installation and operation of the Home firstly change the maximum continuous flow allowance to 0.1 on high guard using the setup

instructions. Run the water in the property and if the water supply is cut off after 6 seconds the installation of the Home is complete. If no water runs on test

check valve polarities.

Setup….

All Waterguard Home controls are pre-set to allow a maximum of 20 MINUTES continuous water flow in low guard and 12 SECONDS in high guard. To

change the default setting, press the button on remote display once to wake it, whichever value is shown is the current guard level. High guard is

differentiated from low guard with the use of a decimal point. Turn dial clockwise to turn up and anticlockwise to turn down then double click to confirm. The

Home Controller will FLASH GREEN and BEEP; x 1 to confirm HI GUARD as current setting, x 2 for LOW GUARD and x 3 for WATER OFF. To change

the other guard level press button on remote once to wake it up, press again to switch guard level, then as before turn dial clockwise to turn up and

anticlockwise to turn down then double click to confirm.

Set up complete.

Technical Support….

Technical support and further product information is available during office hours. Please double check all electrical connections before contacting us. Call

01226 397987 to speak with one our technical experts.

Pairing Mode…..