Watermark WM-BTMIC37 User manual

REV.:001 03/2018SK
Quick Start Guide Bluetooth Music Receiver WM-BTMIC37
Compatible with the following manufacturers / models:
ALFA ROMEO (without Blue & Me) -> 147, 156, 159, Brera, Mito, GT, Spider
FIAT (ohne Blue&Me) -> 500, Bravo year 2007 –2014, Croma from year 2005, Doblo from year
2001, Ducato from year 2002, Idea from year 2004, Multipla from year 1999, Palio, Panda year 2004
–2017, Punto 188 year 1999 –2007, Punto 199 from year 2005, Punto Evo from year 2009, Stilo
from year 2002
LANCIA (without Blue&Me) -> Musa, Ypsilon
OPEL Combo D from year 2011
VW (mit Blaupunkt Radio)Bj. 1998 - 2004
Land Rover Discovery II (Becker Traffic Pro Navi 4775)
Land Rover Freelander (Becker Traffic Pro Navi 4775)
Blaupunkt Porto CD27, Melbourne SD27, Brighton MP27, San Diego MP27, London MP37,
Kingston MP47, Casablanca MP56, Hamburg MP57, Memphis MP66, Las Vegas DVD35, Nashville
DAB35, Bremen, Orlando, Sevilla, Santa Cruz, Milano, San Remo, Essen, Bristol, Vancouver,
Calgary, Laguna, Malaga, Kiel, Acapulco, LA MP74, Bronx MP75, Queens MP56
Becker Indianapolis Pro 7950, 7951, 7952, 7953, 7955
Becker Indianapolis 7850, 7851, 7852, 7853, 7855, 7920, 7921, 7922, 7923, 7925
Connect the adapter:
1. Remove the radio (on the Internet you will find various instructions on this).
2. Before disconnecting the plugs from the radio, make sure that the radio code is available to you as
you will need it for the radio after the power cut.
3. Insert the blue expander of AUX Adapters into the chamber C3 (countersigned red in the picture)
and connect the jack plug to the jack socket (AUX) on the WM-BTMIC37.
4. If necessary, remove the blue connector from the yellow-green-blue connector combination and
attach the blue plug of the WM-BTMIC37 there instead.
5. With a CD changer already connected in chamber C3 (blue), it is thus removed and can no longer be
used in the system.
6. If you have installed a black 20-pin connector in the vehicle, you will also need the adapter WM-4693
(mini-ISO adapter / extension). This can be ordered in our online shop at www.watermark-
germany.de.
7. Position the microphone near the driver in the vehicle (steering wheel trim, instrument panel, etc.).
Lay the cable and connect the jack plug to the jack socket (MIC) on the WM-BTMIC37. Avoid
placing the microphone in the immediate vicinity of or on airbags

8. Now connect the black earth cable to the radio housing or the black cable directly to a ground lead to
the radio connection (i.d.R., brown thick cable). Without a good ground connection, the function of
the adapter is not given.
9. Now connect the red cable (ignition plus + 12V) to a switched + 12V line. Since these are usually no
longer available behind the radio, you can here the voltage, for example. from the cigarette lighter or
the air conditioner (measurement with multimeter necessary). Ignition on = + 12V are on / Ignition off
= 0V are on.
10. Establish a Bluetooth connection by activating Bluetooth pairing and searching for the ``WM´´
Bluetooth device. You should then set the volume to full volume on the connected device.
11. Before reinstalling the radio, test the function of the adapter. Turn on the AUX function by pressing
the CD button several times.
„NO SOURCE AVAILABLE“ appears in the display (only Delphi radios):
1. Remove the blue plug from the WM-BTMIC37 from the radio.
2. Insert the bridge (orange cable) included in delivery with PIN 13 and PIN 14. Thus, the data line is
bypassed and AUX enabled.
3. Connect the blue plug of theWM-BTMIC37 back to the radio.
4. Pressing the CD button repeatedly will now display AUX in the display.