Watlow Electric 1100 User manual

RAYMAX®1120—
Lightweight, Sturdy
Radiant Heater
Panel
The RAYMAX®1120 is a lightweight, yet sturdy and durable
radiant heater panel.The emitter sheath is stainless steel with a
black coating that makes it a highly efficient radiating surface.In
addition, the heater's low mass allows rapid start-up and fast
response to controls.
The patented RAYMAX heater features one-inch (25 mm) wide
emitter strips that are individually replaceable for lower
maintenance costs.Weighing only 5.5 lbs/ft2(26.8 kg/m2), the
heater is easy to mount.
Applications
• Thermoforming
• Textile drying
• Paint curing
• Powder coating fusing
• Shrink wrapping
• Circuit board soldering
FAX-1120-1100
12001 Lackland Road
St. Louis, Missouri 63146 USA
Phone: [phone]
FAX: [phone]
Internet: www.watlow.com
e-mail: [e-mail]
RAYMAX 1120
Features and Benefits
Replaceable emitters
• Reduce your costs
High temperature mica
• Electrically insulates nickel chromium resistance wire,
permitting longer heater life
High emissivity coating on emitter strips
• Improves radiant heating efficiency
One-inch thick thermal insulation
• Backs the emitter strips to reduce backside losses
Uniform full surface heat source
• Provides better, more even heat
Special requirements easily met
• Custom sizes and ratings available
Next day shipment
• Available on stock sizes
;
;
;
Aluminized Steel Case
High Temperature Mica
Sinuated Element Wire
1" Wide Replaceable Stainless Steel
Emitter With High Emissivity Coating
1" (25 mm)
Thermal
Blanket
Insulation
© 2001 Watlow Electric Manufacturing Company

RAYMAX 1120
How to Order
To order your stock RAYMAX heater, specify:
• RAYMAX 1120
• Quantity
• Watlow code number (from Watlow Heater's Catalog)
If our stock units do not meet your application needs,
Watlow can manufacture RAYMAX heaters to your special
requirements. For made-to-order heaters, specify the
following:
• Heated width and length.Three-phase panels must have
width divisible by three.
• Total wattage of each panel.
• Exact voltage and phase. A five percent variation in
voltage at the oven will cause a 10 percent variation
in power.
• Zoning. Indicate dimensions and wattage of each zone.
• Mounting legs or mounting studs, if desired. For studs,
give number and location, or indicate standard location.
• Terminal location if non-standard.
• Terminal box or wire raceway, if required.
Supplying a drawing with an order or request for quotation
can be very helpful in clarifying design information.
Availability
Stock: Next day shipment.
Made-to-Order: Consult Watlow.
Applications and Technical Data
Face Temperature: 1100°F maximum (595°C)
Wattage: Watt densities up to 20 W/in2(3 W/cm2)
Standard Voltage: 120, 240, 480VÅ(ac), 1-phase. Balanced
3-phase available on unit widths divisible by three. Other
voltages are available.
Terminals: Non-standard locations are also available.
Please specify.
Standard Dimensions:±
1⁄16 inch (0.0625 mm)
Typical Peak Energy Wavelength: 3-3.5 microns
Specifications
19/16"(39 mm)
Overall Width =
Heated Width
+ 3/8"(9.5 mm)
Overall Length =
Heated Length
+ 1 1/4"(31.75 mm)
A B
3/8"(9 mm)
3/8"
(9 mm)
7/8"(22 mm)
11/2"
(38 mm) 13/16"
(30 mm)
11/2"
(38 mm)
Width: inches (mm) 1 (25.4) 36 (914.4) 1 (25.4)
Length: inches (mm) 6 (152.4) 70 (1778) any
Area: in2(cm2) 6 (38.7) 864 (5574.2) any
Note: Less than maximum length X width may exceed
maximum area.
Heater Dimensions Min. Max. Increments