watt box WB-150-IPW-1B-2 User manual
™
WB-150-IPW-1B-2
QUICK START GUIDE
POWER
WB-150-IPW-1B-2
CONTROLLED 1
2
ANATOMY
HI
E F G
NETWORK
RESET
POWER
WB-150-IPW-1B-2
CONTROLLED 1
B
A
A
D
C
KJ
3
A. Outlet LEDs: ese illuminate when power to the matching outlet is on.
e outlets are switchable (IP controlled).
B. Power/Network LED: See page 4.
C. AC Power Button: Press to manually toggle the outlets on or o.
D. Mounting Eyelets.
E. Network Connection: Connect to the Local Area Network (LAN) for IP
setup, control, and monitoring.
F. Power Inlet: Outlet for 3-prong IEC power cord.
G. External Fuse*: May need replacement aer an overload.
H. Mounting Bracket Grooves
I. Reset Button: Use a thin tool (paper clip, toothpick) to press this to restart
the network card (no settings are changed). Press and hold 5 seconds to
set the power strip to DHCP. Press and hold 10 seconds to reset the power
strip to factory default.
J. Internet LED: See page 4.
K. Link/Activity LED: See page 4.
* CAUTION: For inlet fuse rating: T15AH, 125VAC/250VAC or F15AH,
125VAC/250VAC. Failure to replace the fuse with the same size, type, and
ratings will damage the device and the connected and nearby equipment, and
will cause electrical shock, re, explosion, or injury.
4
LED INDICATORS
Link/
Activity
LED
Flickering Green: Send/Receive Activity.
O: No data is passing.
Internet
LED
Solid Green: All host pings successful.
Blinking Green: At least one host ping successful.
O: All host pings timed out.
Power/
Network
Solid Amber: Unit has AC power, and a wired network connection.
Solid Green: Unit has AC power, and Wi-Fi is connected.
Blinking Amber: Unit has AC power, and is searching for Wi-Fi.
O: No AC power.
Outlet
LEDs
Solid Green: Outlets ON.
O: Outlets OFF.
Note: Both outlets are jointly controlled on one bank..
PACKAGE CONTENTS
is package contains:
• e WattBox 150 Series Power Strip
• Removable IEC power cord
• 2 wall anchors with M3×16mm screws
5
MOUNTING INSTRUCTIONS
is unit can be mounted on any at surface,
either vertically or horizontally.
Use the screws and anchors provided to install
the unit on a wall as pictured to the right.
Use double-sided tape or hook and loop
closures (not provided) to attach the unit to a
at surface.
An optional mounting bracket is available as a
separate accessory.
CONNECTION DIAGRAM
NETWORK
RESET
Internet
Web Browser
Access
Mobile Apps
Router WB-150-IPW-2
Use OvrC Web and
smartphone apps to
monitor the WattBox
remotely
OvrC Web Server
6
INSTALLATION
NOTE: is device always connects via the wired connection while it is
physically connected to an active network switch port. e Wi-Fi capabilities
are only activated when the device is not hardwired to a network.
1. Ensure the WB-150 is connected by ethernet cable to the internet.
2. Check the IP address of the WB-150 using an IP scanner or the router’s
client table. If your WB-150 will remain hardwired, skip to step 7 now.
Optional Steps for Wireless Operation
3. Navigate to the IP address of the WB-150, and log in to its local interface.
4. In the interface, navigate to Congure > Wireless IP Settings. Press the
Scan button.
5. Locate the SSID for your WAP or router. Select that SSID and log in to that
wireless network.
6. Disconnect the Ethernet cable (otherwise the WB-150 continues to operate
in wired mode). Aer a few minutes, the power LED turns from oraange to
green, indicating that the unit is now operating wirelessly.
Finishing the Install
7. Log in to your OvrC account.
8. Add the WB-150 using its MAC address and service tag (ST) number.
You can now complete setup through OvrC. Ensure your rmware is up to date,
schedule automatic reboots, and set up boot delays.
7
TROUBLESHOOTING
Symptom Possible Cause Remedy
A device won’t
power up when
the WattBox is
turned on.
e WB outlet is
switched o.
Log in to the WattBox interface to turn
the outlet on.
e device is not
turned on.
Turn the device’s power switch on.
WattBox is
not receiving
power (the
LED does not
illuminate 1
minute aer
connecting AC
power).
WattBox is not
turned on.
If the power button does not glow, press
it.
No power is
being supplied.
Ensure the WattBox is plugged into a
properly grounded 120V outlet. Check
the outlet’s switches and circuit breakers.
Too many devices
are connected.
Check the fuse on the AC Inlet. If it is
blown, reduce the load and replace fuse.
Speakers emit
a humming or
buzzing noise.
WattBox is
sharing power
with gear that
is not properly
grounded.
Connect WattBox to a dedicated outlet.
Unplug components one at a time to see
if the noise stops.
8
IMPORTANT SAFETY INSTRUCTIONS
Read and observe the following safety points at all times.
NOTICE
For indoor use only. Internal components are not sealed from the environment. e device can
only be used in a xed location. When you install the device, ensure that the protective earthing
connection of the socket-outlet is veried by a skilled person. Suitable for installation in Information
Technology Rooms in accordance with Article 645 of the National Electrical Code and NFPA 75.
Only use brackets/attachments/accessories specied by the manufacturer.
Do not place the device in an unstable position where it might fall and cause injuries. is
equipment is not suitable for use in locations where children are likely to be present.
Do not cover this device with a cloth. Do not install it on a carpet or rug.
CAUTION – Potential Injury
Do not use this product with extension cords, multioutlet power strips, multioutlet extenders, or
UPS devices (other than a WattBox UPS). e power capacity of these accessories can be overloaded
by this product and may result in a risk of re, or property damage.
WARNING – Power Sources, Grounding, Polarization
is plug is designed to be inserted into a NEMA 5-15 (three-prong grounded) outlet only. Do not
force the plug into an outlet that is not designed to accept it. Never dismantle the plug or to alter the
power cord, and do not attempt to defeat the grounding feature by using a 3-to-2 prong adapter. If
you have questions about grounding, consult your local power company or a qualied electrician.
is WattBox requires a properly grounded outlet for safety. If you’re not sure if your home’s
electrical wiring is properly grounded, have it checked by a qualied electrician.
If a rooop devices such as a satellite dish connects to the WattBox, ensure that the device’s wires
are also properly grounded.
WARNING – Liquid: Avoiding Electrical Shocks
Do not operate the WattBox if liquid of any kind is spilled onto or inside the unit. Do not operate it
near rain or water, even water that is contained (e.g., bathtub or sink).
9
WARNING – Power Cord Safety
Do not place the power cord near areas with heavy foot trac (e.g., hallways). Do not create a trip
hazard with the power cord.
If the power cord’s protective jacket rips or frays, exposing the internal wiring or shielding,
disconnect it from the power source and replace the power cord immediately. See the warranty
section of the owner’s manual for details.
WARNING – No User Serviceable Parts Inside
If the WattBox is not operating properly, do not remove any part of the unit (cover, etc.) for repair.
Unplug the unit and consult the warranty section of the owner’s manual.
CAUTION – Exposure to Heat
Do not expose the WattBox to direct sunlight or place it near wall heaters, space heaters, or in an
enclosed space prone to temperature increase.
Do not use the device in a conned, poorly-ventilated location; this can overheat the unit, possibly
even causing a re. If used in a small space other than an EIA-standard rack, ensure that there is
adequate space around the device.
CAUTION – Proper Cleaning
In general, the only cleaning necessary for is a light dusting. Unplug WattBox from the wall outlet
before cleaning it. Do not use liquid or aerosol cleaners.
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
is equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. ese limits are designed to provide reasonable protection
against harmful interference in a residential installation. is equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the interference by one or more of the following:
10
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the re-
ceiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
is equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. is equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
INDUSTRY CANADA STATEMENT
is device complies with ISED’s license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Radiation Exposure Statement:
is equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. is equipment should be installed and operated with minimum distance of 20 cm
between the radiator and people and animals.
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20
cm de distance entre la source de rayonnement et des personnes ou des animaux.
11
WARRANTY
2-Year Limited Warranty
is SnapAV® product has a 2-Year Limited Product Warranty. is warranty includes parts and
labor repairs on all components found to be defective in material or workmanship under normal
conditions of use. is warranty shall not apply to products which have been abused, modied, or
disassembled. Products to be repaired or replaced under this warranty must be returned to SnapAV
or a designated service center with prior notication and an assigned return authorization number
(RA). Contact technical support for an RA number.
Once you obtain an RA number, please mark the number on the bottom of the unit and pack it in
a shipping carton/box with enough packing material to protect it during transit. e RA number
must also be clearly marked on the outside of the carton. Ship the unit to SnapAV. Please note that
you are responsible for any and all charges related to shipping the unit to SnapAV.
WARRANTY LIMITATION:
SnapAV products not purchased directly from SnapAV or authorized SnapAV dealers or authorized
distributors are excluded from above warranties.
WARNING: is product can expose you to chemicals including lead, which is
known to the State of California to cause cancer and reproductive harm. For more
information go to www.P65Warnings.ca.gov.
!
Version 190605-1550
Retain this label for your records
LOGGING IN TO THE WEB INTERFACE
You need to enter the username and password to access the web interface. e default
entries are below; change these to maintain proper security (and log them below).
Username default: wattbox New Username:
Password default: wattbox New Password:
Table of contents
Other watt box Controllers manuals
