Wave wifi Rogue Wave User manual
Copyright Wave WIFI Inc., 2017. All rights reserved.
AVE
WiFi
On the Water and Online
Rogue Quick Start Guide
Did you get all of your accessories?
POE
Injector
Mount
(not included
with Rogue Pro)
Cigarette adapter
Power Adapter CAT5e
Ethernet Cable
Antenna
HOW TO CONFIGURE / OPERATE:
1. Plug one end of the ethernet cable provided into the base of the unit.
*For Rogue Wave seal the ethernet hole with the white rubber grommet provided*
2. Plug the other end of the ethernet cable into the POE (Power Over Ethernet) injector.
3. Plug the power supply into the POE injector (Both lights on the POE should show solid green).
4. Plug the POE injector into the ethernet port of a laptop, computer or router.
*When plugging into a router it will be the “internet” or “WAN” port.*
:
1. Connect wirelessly to the router that the Rogue unit is physically connected
to via laptop, tablet or smartphone.
2. Open a browser and at the top URL bar type: 192.168.89.1
3. Once on the interface page of the unit, click on a network and type in a
password if needed.
aptop:
2. Open a web browser and at the top URL bar type: 192.168.89.1
3. Once on the interface page of the unit, click on a network and
type in a password if needed.
***Wave WiFi suggests Initial setup be with a Laptop.***
NOTE:
Laptop Computer
Ethernet end plugs into laptop or router.
Power adapter plugs
into wall socket.
Plug the end of the wall
adapter into the input of
the POE
Wall Socket
Cigarette adapter (OPTIONAL)
Plug the cigarette
adapter into a
power source.
Plug the end of
the cigarette
adapter into the
POE input.
CAT5e plugs into
ethernet base of
Rogue unit. And
ethernet end of POE.
Rogue Unit
Rogue Wave
AVE
WiFi
FCC ID: 2ALM9WWR
RESET
12V- 1A
POE
TE000000
ROGUE
M/N:WWR
Rogue Pro & Pro DB
Antenna screws
onto the Rogue
unit.
*Mount not included*
The Rogue Pro has a
screw on 1”- 14
thread base.
(1st) Detach the base
and screw it onto a
mount BEFORE
plugging in the
Ethernet cable.
(2nd) Plug the
ethernet cable into
the ethernet port of
the Rogue.
Ethernet port on the
base of the Rogue
unit.
*Rubber grommet
provided*
Rogue Wave
mount.
Screw on
base.
**NOTE**
Light sequence for 2.4GHz Rogue Wave
& 2.4GHz Rogue Pro only.
Be sure when mounting the Rogue that it is between
15 - 25ft o the water.
Ensure that the cable run is no longer than 60ft. If you go
beyond 60ft the Rogue may not function correctly.
The Rogue must be mounted vertically with the antenna up.
Do not mount next to Radar.
Quick
Tips:
Page 1
you are connected to, to see your current
network status.
Connect the Rogue’s POE adapter
using a router make sure that your laptop or tablet
is connected to the router that the
Rogue is
address from the Rogue (a Windows computer will
generally show the message icon “Connected” at
192.168.89.1 ” into the address bar and press
“enter”. The Network Scan page will then open.
Depending on the device you are using to manage
the Rogue unit; the page look similar to this.
networks (HotSpots) is ordered by signal strength:
the strongest signals are indicated by the color
GREEN. You will also see ORANGE or RED for
signal changes around you. To connect to a
will be a drop down once you click on the network
HotSpot.
During this process the screen will show “ Three
See “Quick Tips”
When using a coupler make sure that is can be used for POE.
again. This should last 30 secs and should be the Rogue as well as the router
it is connected to.
Check the lights on the POE injector. They should both show solid green.
only the “DC” light is on then the Rogue is not receiving power. Check all
the ethernet cable is sliding out of the Rogue unit then check that the
ethernet port tabs are not damaged).
Copyright Wave WIFI Inc., 2017. All rights reserved.
Follow Us!
AVE
WiFi
On the Water and Online
page. “Disabling EC Firewall” removes your
users. However, it may be necessary to disable
this feature to access some HotSpots. Clicking
“reboot” disconnects the Rogue from the
current hotspot and also refreshes the
reboot if the hotspot is not a favorited
1.) Connect to the network that you want to favorite.
2.) Once connected, click the yellow star to the left of the network
bar to favorite the Wi-Fi network source.
TIP: You can see a full listing of all favorited networks in the
“favorites” link to the left of the screen. You can also delete
a network from your favorites in this same location.
Rogue Quick Start Guide
Page 2
How to Install Rogue Units
*Mount not included*
PRO
BASE
1.
Rogue Pro. (1st) Detach the base and screw it onto a mount BEFORE plugging in the Ethernet cable.
3. (Once instructed) Plug the ethernet cable into the ethernet port of the Rogue unit. For Rogue Pro you may need to do this BEFORE screwing the body of
the Rogue Pro back onto its base (see point “ 1”).
2. The Ethernet port is on the base of the Rogue unit.
1.
1.
2.
3.
4.
6.
facing upward, without stressing the “N” connector of the male head.
7. 3”).
8.
9. Plug the power supply into the POE injector and validate that the “DC” light and the “Power” light are both showing on the injector. The “power”
10.
AVE
WiFi
On the Water and Online
Copyright Wave WIFI Inc., 2017. All rights reserved.
Page 3
FCC Warning:
Any Changes or modications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
---Please contact a professional person to install and operate.
Page 4
This manual suits for next models
2
Other Wave wifi Extender manuals
