Wave 4PSWT User manual

4PSWT
4-Position Sequencing,
Alarming, Homing, &
Bypassing Switcher
Operation Manual
November 2006

WARNING: TO PREVENT FIRE
OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS
APPLIANCE TO RAIN
OR MOISTURE
Thelightningflashwiththearrowheadsymbol,withinanequilateraltriangle,is
intended to alert the user to the presence of uninsulated “dangerous voltage”
withintheproduct’senclosurethatmaybeofsufficientmagnitudetoconstitute
a risk of electrical shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING!
This equipment generates, uses, and can radiate radio frequency energy
and if not installed and used in accordance with the instructions manual,
may cause interference to radio communications. It has been
tested and found to comply with the limits for a class A computing device
pursuant to subpart J of part 15 of FCC rules, which are designed to provide
reasonable protection against such interference when operated in a
commercialenvironment.
Operation of this equipment in a residential area is likely to cause interference
in which case the user at his own expense will be required to take whatever
measures
CAUTION!
RISK OF ELECTRICAL SHOCK
DO NOT OPEN CAUTION!
TO PREVENT ELECTRIC SHOCK
DO NOT REMOVE COVER.
NO USER SERVICEABLE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
2

3
INTRODUCTION
The 4PSWT is a 4 position sequencing, alarming, bypassing, and homing
switcher. The front panel toggleswitchallows for automatic sequencing,
homing, and by-passing of the 4 video inputs. Sequencing is controlled by a
front panel recessed dwell pot. This pot is recessed to eliminate accidental
adjustment.Thedwelladjustmentvaries fromapproximately.2secondto60
seconds.
OPERATION
The 4 toggle switches control homing, sequencing and by-passing. The
LEDs above each toggle switch give a visual indication of the current
camera. Homing any camera will stop the sequence mode and display the
selected camera. If no homing switch is used, the switcher sequences
through all cameras selected for sequencing in the loop.When a toggle
switch is in the “BYPASS” position, the switcher willl drop this camera from
the sequence or bypass it. When the toggle switch is in the “SEQUENCE”
position this camera is included in the sequence.
DWELL
The dwell or time
that each camera
appears on-screen
can be adjusted by
the recessed front
panel control. This can be varied from approximately .2 seconds to 60
seconds. Use a small flat bladed screwdriver to adjust this control. Turning
this pot to the right increases the dwell time.
ALARMING
The alarming feature is tied to camera position 4 of the 4PSWT. The alarm
input is located on the rear of the switcher. This compression type connec-
tor allows for the connection of an alarm switch or other alarming device.
To open the cage clamp, insert a small, flat bladed screwdriver
in the small slot below the clamp. When inserted, push the screwdriver
slightlydownwardsto open the clamp. Nowinsertthe wire and remove the
screwdriver blade. When an alarm is connected, the switcher will always

“HOME” to camera four on an alarm. Homing to camera four will occur on
an alarm regardless of the switch positions of the other cameras. If camera
four is in the bypass mode, it will still home upon an alarm and return to the
sequence or other selected modes upon the completion of the alarm. If
cameras 1, 2, and 3 are sequencing, and camera 4 is in the bypass mode,
upon an alarm the switcher will home to camera 4 for the alarm duration;
then, when the alarm stops, it will continue the sequence from where it was
when the alarm was triggered.
NOTE: Upon powering up the 4PSWT, the switcher waits one dwell
time to initialize. This may take from 1 second to 1 minute depending
on the present dwell time setting.
POWER
The switcher is powered by the included wall transformer. The unit can be
powered from 9 to 12VDC. The center post of the DC Coax is POSITIVE.
CONNECTIONS
The VIDEO inputs are BNC type connectors. The inputs are 75 ohm
terminated and require 1V P-P. The output is 1V P-P and will drive a 75
ohm load. Connect the video cameras to the switcher in the desired order.
Connect Video out to your VCR or Monitor. Plug in the DC Coax connector.
The switcher is now operational. Select the desired front panel controls and
adjustthedwell.
4
_____________________________________________
InternalJumperSettings:
JP2=open JP3=shorted

5
SPECIFICATIONS
Video Inputs (Parent & Inset)......................1V P-P 75 ohm terminated
Video Output ........................1V P-P 75 ohms terminated or unterminated
Power Supply ............................................................9-12VDC @ 100 mA
Video Inputs.........................................................toggle switch selectable
Toggle positions..............................................Bypass, Sequence & Home
Dwell adjust........................................................ Front panel recessed pot
Dwell Time...............................From approximately .2 second to 1 minute
Alarm Input......................................Screw terminal with quick disconnect
NO (Normally Open), Hi-Z, Dry Contact
Camera Position................................................... LED indicators (4) RED
Connectors:
Video In/Out........................................................................BNC
Power Input........................................DC Coax 2.1mm x 5.5mm
Alarm Inputs ..................Screw terminal with quick disconnect
Mechanical:
Case ........................ Beige Metal 5.13” W x 4.90” L x 1.38” H
(130mmW x 125mmL x 35mmH)
Weight.............................................................0.60 kg.(1.32lbs.)
Box Size.........................................8.0” W x 7.0” L x 2.5” H
(240mmW x 178mmL x 64mmH)

6
LIMITED WARRANTY
(Terms and Conditions)
For2 Years from the dateofshipment, Seller warrants to Buyerthatthe Prod-
uct is free from defects in material or workmanship under normal use and
service. EquipmentmanufacturedbyotherthanSellerbutfurnishedbySeller
carries the same warranty to Buyer as Seller receives from the other manu-
facturer, notwithstanding any provision to the contrary. If Buyer has specified
aparticularmanufacturer’sproductwhichisnotthebrandstandardlysupplied
bySeller, Buyershalllookonlytotheothermanufacturer’swarrantyandSeller
shall not warrant such item.
EXCLUSIONS. Seller’s warranty does not cover the following:
(1) in-transit damage claims, improper handling by carrier or post office
(Note: only the consignee of the shipment can file a claim with the
common carrier)
(2) damages caused by incorrect use, modification, carelessness,
improper storage, hostile operating conditions, or unauthorized
service, installation or repairs without proper training from the Seller
(3) damages caused by fire, flood, lightning, collision, acts of God or
other events beyond the control of Seller
(4) products or parts thereof that have had serial numbers removed,
altered or defaced
(5) products returned without an RMA number and sales or delivery
receipt showing the date of original purchase
(7) use of components that do not meet Seller’s specifications
(9) external parts such as cabinets or keypads
(10) periodic maintenance and adjustments resulting from normal use
WARRANTIES EXCLUDED, SELLER EXPRESSLY DISCLAIMS AND EX-
CLUDES ANY EXPRESS OR IMPLIED WARRANTY OR MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEEDS OR
IS INCONSISTENT WITH THE WARRANTY HEREIN EXPRESSLY SET
FORTH.
NON-WARRANTY CLAIMS. In the event Buyermakesawarranty claim and
Seller’s warranty does not apply, Buyer shall reimburse Seller for all reason-
ableexpensesincurredbySellerindiagnosingtheinstallation/repairproblem.

7
BUYER’S EXCLUSIVE REMEDIES. If the Product supplied shall fail to con-
formtothe contract or any applicable warranty,Buyershallimmediatelynotify
Seller of such condition and afford Seller a reasonable opportunity to inspect
said Product. Seller shall, at its option, either repair or replace such noncon-
forming Product. Seller shall not be responsible for labor charges for removal
or installation of such equipment or material or charges for transportation,
handlingandshipping except as provided in Seller’swrittenservicepolicy. No
Product shall be returned without Seller’s prior written consent.
SELLER SHALL NOT BE LIABLE FOR ANY SPECIAL, DIRECT INCIDEN-
TAL OR CONSEQUENTIAL DAMAGES OF A COMMERCIAL NATURE
ARISING OUT THE USE OF OR INABILITY TO USE SELLER’S PRODUCT
BYREASONOFTHE FACTTHAT SUCH PRODUCT DOES NOT CONFORM
TO THE CONTRACT OR TO ANY EXPRESS OR IMPLIED WARRANTY.
SELLER’S MAXIMUM LIABILITY SHALL BE LIMITED TO THE COST OF
REPAIR AND/OR REPLACEMENT OF THE PRODUCT CLAIMED TO BE
DEFECTIVE OR NONCONFORMING, SUBJECT TO SELLER’S RIGHT OF
REMOVAL AND RETURN OF PRODUCT.
All of the foregoing constitute Buyer’s sole and exclusive remedy and Seller’s
sole and exclusive liability for supplying nonconforming or defective Product.
RETURNS. AVE products are fully inspected and carefully packed to ensure
you are delivered a quality product in good condition. If you are not fully
satisfied with our product, returns of standard stocking items with no restock-
ingfeecanbe made within thirty (30) days of invoice to Buyer. Allsuch returns
must have prior consent of Seller by obtaining an RMA number and must
includethesalesor delivery receipt showing the date oforiginalpurchaseand
be in an unused condition contained in its original packaging. Any other re-
turns must have prior written consent of Seller and are subject to a restocking
fee of fifteen percent (15%) and freight charges.
RMA NUMBER. The RMA (Return Material Authorization) number must be
obtained by contacting Seller prior to the shipment of the the product for re-
turn. The RMA number is valid only for 15 days from the date of issue. The
RMA number must be clearly displayed on all shipping labels.

8
ASIA
AVE (Thailand) Co., Ltd.
217/4CrystalGarden
Soi4(Nanatai), Sukhumvit Rd.
Klongtoey,Klongtoey
Bangkok,10110 Thailand
Tel: [phone]
Fax:[phone]
Email: [email protected]
www.avethailand.com
NORTHAMERICA
AVE USA
2000WestGovernors Circle, Suite E
Houston,Texas77092
Tel:[phone]
Fax:[phone]
Email:[email protected]
www.americanvideoequipment.com
WESTERNEUROPE
AVE Multiview
Unit1C,The Potteries,
WoodgreenRoad, Waltham Abbey
Essex, EN9 3SA, UK
Tel:[phone]
Fax:[phone]
Email:[e-mail]
www.multiview.net