wavestore Vision WV-8S-180-AI User manual

WV-8S-180-AI
Before installing and using the camera,
please read this manual carefully.
Be sure to keep it handy for future reference.
Wavestore Vision 4K 180°
IR Bullet IP Camera
Installation Guide

2
INTRODUCTION
03 Important Safety Information
06 Product & Accessories
07 Part Name
INSTALLATION
08 Installation
09 Cabling
11 Inserting / Removing an SD Memory Card
SPECIFICATION
12 Dimension
Contents

3
POWER
1. Use only standardized adapters written in the manual.
Incorrect connection of the power source can cause fire,
electric shock, or failure.
2. If there is smoke or a strange smell from the power
source, disconnect the power immediately and contact
the service center or purchasing office. If you continue to
use it as it is, it can cause fire and electric shock.
3. Disconnect the power plug from the outlet before
connecting to the power terminal block.
INSTALLATION
1. Install it according to the temperature and humidity environment
suitable for the product specifications. Otherwise, it can cause
fire and electric shock.
2. Thunder and lightning can cause problems with the camera.
When installing, be careful to minimize damage caused by
lightning such as grounding.
3. Do not place conductive materials (drivers, coins, metal
sticks, etc.) and water-filled containers on the camera. It
causes injuries caused by fire, electric shock, and falling.
4. If you want to move the installed product, turn off the
power and move it or reinstall it. Otherwise, it can cause
fire and electric shock.
5. Do not install it in places where there is a lot of moisture,
dust, soot, etc. It causes fire and electric shock .
6. Avoid places where direct sunlight comes in or where heat
comes out, such as heating appliances. It causes fire and electric
shock.
CLEANING
1. Do not spray water directly on each part of the product
when cleaning. It causes fire and electric shock.
POWER
1. Use the power line after fixing it firmly to the power connection
terminal. Incomplete connection can cause a fire.
2. Do not extend the adapter output cable. If you need to
install the power cable extension, please contact the
service center.
3. Use insulated power for PoE connected external power.
INSTALLATION
1. It is recommended not to touch the lens when installing
the product as the factory ships with a focus adjustment
completed during the manufacturing completion
inspection phase.
2. Avoid installing cameras facing bright lights like sunlight.
Causes damage to the image sensor.
3. Make sure it safe and securely when installing camera on
the wall or ceilling. This can cause injury by the fall.
4. Do not connect multiple cameras to one adapter. Excess
capacity causes abnormal heat and fire.
5. Wear protective gloves when installing/uninstalling the
camera. This causes burns caused by high temperature
on the surface of the product.
6. Don't drop or shock the product. Please stay away from
places where vibration is severe or magnet types are
present.
7. Install it in a well-ventilated place. This can cause fire and
failure.
CLEANING
1. Wipe the contaminated surface with a clean, soft, dry
cloth or wet the soft, dry cloth to prevent water from
flowing, then wipe the contaminated area.
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss.
If the product is not functioning properly or damaged, contact the service center or purchasing office.
Warnings
Serious injury or death may be caused
if any of these warnings are neglected.
Cautions
Injury or equipment damage may be caused if any
of these cautions are neglected.

4
Installation and Use Precautions
1. The battery (battery pack or equipped battery) must not be exposed to excessive heat such as sunlight, fire, etc.
2. Do not disassemble the camera at your discretion.
3. If you forcefully install the product with excessive force, malfunction can damage the camera.
4. Do not punch or shake the camera and be careful not to damage the camera with careless storage or malfunction.
5. Be careful not to install the camera in a rainy or humid place, and do not leave it in a wet place.
6. Installing or using the product in water can cause serious product failure.
7. Do not install the product if there is chemical or vapor in the place where the product is installed, or if it can be generated.
8. Be careful not to get chemicals on the surface of the product when installing the product. Chemical solvents such as cleaning
agents and adhesive components can cause fatal damage to the surface of the product.
9. Do not install it near the kitchen or cooking table as edible oil such as soybean oil can also cause product damage and
deformation. It can cause product damage.
10. Be careful not to get foreign substances on the Micro SD card terminal. If there is any foreign substance, wipe it with a soft
cloth.
11. Data will not be saved at the end of the life of the Micro SD card. In this case, purchase a new Micro SD card.
12. Moisture may occur in the glass of the camera when the new product box is opened (or when the product is initially running).
The generated moisture is removed by a Gore vent attached to the camera within hours of the power connection.
13. For products enclosed with a desiccant or card-type absorbent, please install it according to the manual.
14. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus.
15. Unplug this apparatus when a cart is used. Use caution when moving the cart/apparatus
combination to avoid injury from tip-over.

5
Disposal of Old Appliances
1. When this crossed-out wheel bin symbol is attached to a product it means the product is covered by
the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately form the municipal waste
stream stream in accordance to laws designated by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for
the environment and human health.
4. For more detailed information about disposal of your old appliance, please contact your city office,
waste disposal service or the shop where you purchased the product.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interferenece at his own expense.

6
Introduction -
Product & Accessories
Torx Wrench
(T10, T20)
Template Sheet Quick Manual Desi-Pak
(Moisture Absorber)
Screw &
Plastic Anchor - 4pcs
Camera
Cables
Please check if all the camera and accessories are included in the package.
D
ES
IP
SI
PA
K
Absorber GuideTest Monitor Cable
Waterproof cap & Gasket
& Rubber 2ea
(Black : ø4 / White : ø5)
Note : Cable thickness 4.5ø to 5.5ø uses a black rubber, and over 5.5ø uses a white rubber.

7
Introduction -
Part Name
Sunshield Adjusting Screw
Side Cover
Pan/Tilt Stopper Screw
Bracket
Audio In/Out
Alarm In/Out
Sunshield
Lens
IR LED
RJ-45 Connector
Waterproof Cap
DC Power Jack

8
Installation -
Installation
Before installing your camera, you have to read the following cautions.
1. You have to check whether the location can bear five times of the weight of your camera.
2. Don’t let the cable to be caught in improper place or the electric line cover to be damaged.
Otherwise it may cause a breakdown or fire.
3. When installing your camera, don’t allow any person to approach the installation site. If you have any valuable things under the
place, move them away.
1Using the Template sheet, make the cabling hole on the
wall/ceiling.
2Connect the network cable, power cable respectively.
See the section ‘Installation - Cabling’ for details.
3Fix the camera on the wall/ceiling by screw provided.
Loosen the Pan/Tilt stoper screw a litte before fixing the
camera.
4By using the test video cable, check the screen during
installation.
Desi-Pak (Moisture Absorber)
When installing, unseal the vacuum-packed Desi-Pak and
install it in the marked position.
When inserting or removing Desi-Pak, be careful as it may
be torn if you use a pointed tool.
Reset to the Factory Default
Press the reset button for 5 seconds to return the setup
to the factory default.
Warning :
If you press the ‘Reset’ button, you will lose all setting
data. If needed, please, make a note for further installation.
SD Card Slot
Reset Button
Test Video Output
DESI PAK
DESI PAK
DESI P
D
D
SI PAK

9
Installation -
Cabling
1. Using a PoE-Enabled Switch
The Camera is PoE-compliant, allowing transmission of
power and data via a single Ethernet cable.
PoE eliminates the need for the different cables used to
power, record, or control the camera. Follow the illustration
below to connect the camera to a PoE-enabled switch using
an Ethernet cable.
2. Using a Non-PoE Switch
If a PoE-enabled switch is not used, use a power adaptor
for power transmission and non-PoE switch for data
transmission.
Follow the illustrations below to connect the camera
without a PoE-enabled Switch.
Two Options
Use a PoE-enabled swtich to connect data and power through a single cable and begin viewing and recording images instantly.
A non-PoE switch will require an adaptor for power transmission.
Ethernet Cable Ethernet Cable
Power
How to connect to the network through the water proof cable
Insert the Lan cable into the rubber first as (a) below.
Put the Lan cable into (b), then (c) will be assembled to
(b) tightly. As a final step, (d) need to be assembled to (c)
without making any space.
bc
d
a

10
1Power
2Network
3Audio Output
4Audio Input
5Alarm Output
6Alarm Input
5~6Alarm In/Out
DI (+) WHITE
DI (-) YELLOW
DO (-) SKY BLUE
DO (+) GRAY + DOT
Installation -
Cabling
1Power Connection
Please, check the voltage and current capacity of rated
power carefully.
2Network Connection
Connect the crossover cable into the RJ-45.
3Audio Output
Connect the ‘Audio Out’ cable of the camera to device like
speaker.
Audio Out supports only RTSP Back channel function.
It plans to make it available on the web later.
4Audio Input
Connect the ‘Audio In’ cable of the camera to the device
like microphone.
5Alarm Output
It connects to the alarm lights, siren or lamps, and it is
activated according to the Setup menu setting.
Cable of the relay output device should connect to sky blue
and gray+dot line of the Alarm Cable.
6Alarm Input/Sensor
Cable of the sensor/alarm input device should connect to
yellow and white line of the Alarm Cable.
Rate Power Power
Consumption PoE
DC 12V 8.9W IEEE 802.3af class3

11
Installation -
Inserting/Removing an SD Memory Card
Micro
The memory card is an external data storage device
that has been developed to offer an entirely new way
to record and share video, audio, and text data using
digital devices.
Recommended SD Card Specification (Not Included)
- Type: Micro SD (SD/SDHC/SDXC)
- Manufacturer: SanDisk, Samsung, Transcend, Micron
- Capacity: 4GB~128GB
- Class: UHS-I U3 Class 10
New Micro SD card over 64GB must be formatted
on the first use.
1Inserting an SD Memory Card
Insert the SD card in the arrow direction.
Don’t insert the SD memory card while it’s upside down
by force. Otherwise, it may damage the SD memory
card.
2Removing an SD Memory Card
Removing a SD Memory Card Gently press down on the
exposed end of the memory card as shown in the diagram
to eject the memory card from the slot.
Pressing too hard on the SD memory card can cause the
card to shoot out uncontrollably from the slot when
released.
If you have saved data in the SD memory card, removing
the SD memory card prior to setting record to OFF will
cause damage to the data stored in the card.

12
Specifications -
Dimension
Unit : mm
ø78
127.9
ø4.2
78
228
96.7