wavestore WV-CT-4F User manual
WV-CT-4F
Wavestore Vision Thermal
Mini Bullet IP Camera
Quick Guide
1. Product & Accessories 2. Part Name 3. Installation
To disconnect power from the mains, pull out the mains cord plug. When install the product, ensure that
the plug is easily accessible.
Camera
Cables
Sunshield
Lens
RJ-45 Connector
BNC Cable
DC Power Jack
Audio, Sensor,
Alarm Cable
Waterproof Cap
Bracket
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the userwill be required to correct the interferenece at his own expense.
Before installing your camera, you have to read the following cautions.
1. You have to check whether the location can bear five times of the weight of your camera.
2. Don’t let the cable to be caught in improper place or the electric line cover to be damaged.
Otherwise it may cause a breakdown or fire.
3. When installing your camera, don’t allow any person to approach the installation site.
If you have any valuable things under the place, move them away.
Please check if all the camera and accessories are included in the package.
1Drill three holes on the installation
surface based on the provided
installation template.
2Insert the plastic anchors into the
holes.
3Install the provided ferrite core on the
cable.
4Attach the provided wall cushion to
the bottom of the camera’s pan/tilt
bracket.
5Fix the camera to the installation
surface.
A. Align the screw holes of the camera’s pan/
tilt bracket and the plastic anchors.
B. Insert the provided screw into the plastic
anchors through the screw holes of the
camera’s pan/tilt bracket.
C. Tighten the screws firmly into the plastic
anchors.
6Connect all the necessary cables.
7Adjust the angle.
Template SheetTorx Wrench
Screw & Plastic Anchor - 3pcs Quick Manual
Safety Information Installation and Use Precautions
POWER
1. Use the power line after fixing it firmly to the power connection terminal.
Incomplete connection can cause a fire.
2. Do not extend the adapter output cable. If you need to install the power cable
extension, please contact the service center.
3. Use insulated power for PoE connected external power.
INSTALLATION
1. It is recommended not to touch the lens when installing the product as the factory
ships with a focus adjustment completed during the manufacturing completion
inspection phase.
2. Avoid installing cameras facing bright lights like sunlight. Causes damage to the
image sensor.
3. Make sure it safe and securely when installing camera on the wall or ceilling. This
can cause injury by the fall.
4. Do not connect multiple cameras to one adapter. Excess capacity causes abnormal
heat and fire.
5. Wear protective gloves when installing/uninstalling the camera. This causes burns
caused by high temperature on the surface of the product.
6. Don't drop or shock the product. Please stay away from places where vibration is
severe or magnet types are present.
7. Install it in a well-ventilated place. This can cause fire and failure.
CLEANING
1. Wipe the contaminated surface with a clean, soft, dry cloth or wet the soft, dry cloth
to prevent water from flowing, then wipe the contaminated area.
1. The battery (battery pack or equipped battery) must not be exposed to excessive
heat such as sunlight, fire, etc.
2. Do not disassemble the camera at your discretion.
3. If you forcefully install the product with excessive force, malfunction can damage
the camera.
4. Do not punch or shake the camera and be careful not to damage the camera with
careless storage or malfunction.
5. Be careful not to install the camera in a rainy or humid place, and do not leave it in a
wet place.
6. Installing or using the product in water can cause serious product failure.
7. Do not install the product if there is chemical or vapor in the place where the
product is installed, or if it can be generated.
8. Be careful not to get chemicals on the surface of the product when installing the
product. Chemical solvents such as cleaning agents and adhesive components can
cause fatal damage to the surface of the product.
9. Do not install it near the kitchen or cooking table as edible oil such as soybean oil
can also cause product damage and deformation. It can cause product damage.
10. Be careful not to get foreign substances on the Micro SD card terminal. If there is
any foreign substance, wipe it with a soft cloth.
11. Data will not be saved at the end of the life of the Micro SD card. In this case,
purchase a new Micro SD card.
12. Moisture may occur in the glass of the camera when the new product box is opened
(or when the product is initially running). The generated moisture is removed by a
Gore vent attached to the camera within hours of the power connection.
13. For products enclosed with a desiccant or card-type absorbent, please install it
according to the manual.
14. Use only with cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus.
15. Unplug this apparatus when a cart is used. Use caution when
moving the cart/apparatus combination to avoid injury from
tip-over.
WARNINGS : Serious injury or death may be caused
if any of these warnings are neglected.
BATTERY
1. There is a risk of explosion if the battery is incorrectly replaced. The battery should
be replaced only with the same battery.
2. Used batteries must be disposed of according to local regulations or battery
manufacturer's instructions. Disposing of in a fire or in a hot oven, or mechanically
crushing and cutting may cause an explosion.
3. Leaving the battery in a very high temperature or low air pressure environment may result
in an explosion or leak of flammable liquids or gases.
POWER
1. Use only standardized adapters written in the manual. Incorrect connection of the
power source can cause fire, electric shock, or failure.
2. If there is smoke or a strange smell from the power source, disconnect the power
immediately and contact the service center or purchasing office. If you continue to
use it as it is, it can cause fire and electric shock.
3. Disconnect the power plug from the outlet before connecting to the power terminal block.
INSTALLATION
1. Install it according to the temperature and humidity environment suitable for the
product specifications. Otherwise, it can cause fire and electric shock.
2. Thunder and lightning can cause problems with the camera. When installing, be
careful to minimize damage caused by lightning such as grounding.
3. Do not place conductive materials (drivers, coins, metal sticks, etc.) and water-filled
containers on the camera. It causes injuries caused by fire, electric shock, and falling.
4. If you want to move the installed product, turn off the power and move it or reinstall it.
Otherwise, it can cause fire and electric shock.
These instructions are intended to ensure that the user can use the product
correctly to avoid danger or property loss.
If the product is not functioning properly or damaged, contact the service center or
purchasing office.
CAUTIONS : Injury or equipment damage may be caused
if any of these cautions are eglected.
5. Do not install it in places where there is a lot of moisture, dust, soot, etc. It causes
fire and electric shock.
6. Avoid places where direct sunlight comes in or where heat comes out, such as
heating appliances. It causes fire and electric shock.
CLEANING
1. Do not spray water directly on each part of the product when cleaning. It causes fire
and electric shock.
CAUTION : Risk of explosion if battery is replaced by an incorrect type.
Dispose of used of used batteries according to the instructions.
ATTENTION : Il y a risque d'explosion si la batterie est remplaée par une batterie de type incorrect.
Mettre au rebut les batteries usagees conformément aux instructions.
Waterproof cap & Gasket
& Rubber 2ea
(Black : ø4 / White : ø5)
Note : Cable thickness 4.5ø to 5.5ø uses a black rubber, and over 5.5ø uses a white
rubber.
www.wavestore.com
WV-CT-4F
Wavestore Vision Thermal
Mini Bullet IP Camera
Quick Guide
1. Product & Accessories 2. Part Name 3. Installation
To disconnect power from the mains, pull out the mains cord plug. When install the product, ensure that
the plug is easily accessible.
Camera
Cables
Sunshield
Lens
RJ-45 Connector
BNC Cable
DC Power Jack
Audio, Sensor,
Alarm Cable
Waterproof Cap
Bracket
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the userwill be required to correct the interferenece at his own expense.
Before installing your camera, you have to read the following cautions.
1. You have to check whether the location can bear five times of the weight of your camera.
2. Don’t let the cable to be caught in improper place or the electric line cover to be damaged.
Otherwise it may cause a breakdown or fire.
3. When installing your camera, don’t allow any person to approach the installation site.
If you have any valuable things under the place, move them away.
Please check if all the camera and accessories are included in the package.
1Drill three holes on the installation
surface based on the provided
installation template.
2Insert the plastic anchors into the
holes.
3Install the provided ferrite core on the
cable.
4Attach the provided wall cushion to
the bottom of the camera’s pan/tilt
bracket.
5Fix the camera to the installation
surface.
A. Align the screw holes of the camera’s pan/
tilt bracket and the plastic anchors.
B. Insert the provided screw into the plastic
anchors through the screw holes of the
camera’s pan/tilt bracket.
C. Tighten the screws firmly into the plastic
anchors.
6Connect all the necessary cables.
7Adjust the angle.
Template SheetTorx Wrench
Screw & Plastic Anchor - 3pcs Quick Manual
Safety Information Installation and Use Precautions
POWER
1. Use the power line after fixing it firmly to the power connection terminal.
Incomplete connection can cause a fire.
2. Do not extend the adapter output cable. If you need to install the power cable
extension, please contact the service center.
3. Use insulated power for PoE connected external power.
INSTALLATION
1. It is recommended not to touch the lens when installing the product as the factory
ships with a focus adjustment completed during the manufacturing completion
inspection phase.
2. Avoid installing cameras facing bright lights like sunlight. Causes damage to the
image sensor.
3. Make sure it safe and securely when installing camera on the wall or ceilling. This
can cause injury by the fall.
4. Do not connect multiple cameras to one adapter. Excess capacity causes abnormal
heat and fire.
5. Wear protective gloves when installing/uninstalling the camera. This causes burns
caused by high temperature on the surface of the product.
6. Don't drop or shock the product. Please stay away from places where vibration is
severe or magnet types are present.
7. Install it in a well-ventilated place. This can cause fire and failure.
CLEANING
1. Wipe the contaminated surface with a clean, soft, dry cloth or wet the soft, dry cloth
to prevent water from flowing, then wipe the contaminated area.
1. The battery (battery pack or equipped battery) must not be exposed to excessive
heat such as sunlight, fire, etc.
2. Do not disassemble the camera at your discretion.
3. If you forcefully install the product with excessive force, malfunction can damage
the camera.
4. Do not punch or shake the camera and be careful not to damage the camera with
careless storage or malfunction.
5. Be careful not to install the camera in a rainy or humid place, and do not leave it in a
wet place.
6. Installing or using the product in water can cause serious product failure.
7. Do not install the product if there is chemical or vapor in the place where the
product is installed, or if it can be generated.
8. Be careful not to get chemicals on the surface of the product when installing the
product. Chemical solvents such as cleaning agents and adhesive components can
cause fatal damage to the surface of the product.
9. Do not install it near the kitchen or cooking table as edible oil such as soybean oil
can also cause product damage and deformation. It can cause product damage.
10. Be careful not to get foreign substances on the Micro SD card terminal. If there is
any foreign substance, wipe it with a soft cloth.
11. Data will not be saved at the end of the life of the Micro SD card. In this case,
purchase a new Micro SD card.
12. Moisture may occur in the glass of the camera when the new product box is opened
(or when the product is initially running). The generated moisture is removed by a
Gore vent attached to the camera within hours of the power connection.
13. For products enclosed with a desiccant or card-type absorbent, please install it
according to the manual.
14. Use only with cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus.
15. Unplug this apparatus when a cart is used. Use caution when
moving the cart/apparatus combination to avoid injury from
tip-over.
WARNINGS : Serious injury or death may be caused
if any of these warnings are neglected.
BATTERY
1. There is a risk of explosion if the battery is incorrectly replaced. The battery should
be replaced only with the same battery.
2. Used batteries must be disposed of according to local regulations or battery
manufacturer's instructions. Disposing of in a fire or in a hot oven, or mechanically
crushing and cutting may cause an explosion.
3. Leaving the battery in a very high temperature or low air pressure environment may result
in an explosion or leak of flammable liquids or gases.
POWER
1. Use only standardized adapters written in the manual. Incorrect connection of the
power source can cause fire, electric shock, or failure.
2. If there is smoke or a strange smell from the power source, disconnect the power
immediately and contact the service center or purchasing office. If you continue to
use it as it is, it can cause fire and electric shock.
3. Disconnect the power plug from the outlet before connecting to the power terminal block.
INSTALLATION
1. Install it according to the temperature and humidity environment suitable for the
product specifications. Otherwise, it can cause fire and electric shock.
2. Thunder and lightning can cause problems with the camera. When installing, be
careful to minimize damage caused by lightning such as grounding.
3. Do not place conductive materials (drivers, coins, metal sticks, etc.) and water-filled
containers on the camera. It causes injuries caused by fire, electric shock, and falling.
4. If you want to move the installed product, turn off the power and move it or reinstall it.
Otherwise, it can cause fire and electric shock.
These instructions are intended to ensure that the user can use the product
correctly to avoid danger or property loss.
If the product is not functioning properly or damaged, contact the service center or
purchasing office.
CAUTIONS : Injury or equipment damage may be caused
if any of these cautions are eglected.
5. Do not install it in places where there is a lot of moisture, dust, soot, etc. It causes
fire and electric shock.
6. Avoid places where direct sunlight comes in or where heat comes out, such as
heating appliances. It causes fire and electric shock.
CLEANING
1. Do not spray water directly on each part of the product when cleaning. It causes fire
and electric shock.
CAUTION : Risk of explosion if battery is replaced by an incorrect type.
Dispose of used of used batteries according to the instructions.
ATTENTION : Il y a risque d'explosion si la batterie est remplaée par une batterie de type incorrect.
Mettre au rebut les batteries usagees conformément aux instructions.
Waterproof cap & Gasket
& Rubber 2ea
(Black : ø4 / White : ø5)
Note : Cable thickness 4.5ø to 5.5ø uses a black rubber, and over 5.5ø uses a white
rubber.
www.wavestore.com
WV-CT-4F
Wavestore Vision Thermal
Mini Bullet IP Camera
Quick Guide
1. Product & Accessories 2. Part Name 3. Installation
To disconnect power from the mains, pull out the mains cord plug. When install the product, ensure that
the plug is easily accessible.
Camera
Cables
Sunshield
Lens
RJ-45 Connector
BNC Cable
DC Power Jack
Audio, Sensor,
Alarm Cable
Waterproof Cap
Bracket
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the userwill be required to correct the interferenece at his own expense.
Before installing your camera, you have to read the following cautions.
1. You have to check whether the location can bear five times of the weight of your camera.
2. Don’t let the cable to be caught in improper place or the electric line cover to be damaged.
Otherwise it may cause a breakdown or fire.
3. When installing your camera, don’t allow any person to approach the installation site.
If you have any valuable things under the place, move them away.
Please check if all the camera and accessories are included in the package.
1Drill three holes on the installation
surface based on the provided
installation template.
2Insert the plastic anchors into the
holes.
3Install the provided ferrite core on the
cable.
4Attach the provided wall cushion to
the bottom of the camera’s pan/tilt
bracket.
5Fix the camera to the installation
surface.
A. Align the screw holes of the camera’s pan/
tilt bracket and the plastic anchors.
B. Insert the provided screw into the plastic
anchors through the screw holes of the
camera’s pan/tilt bracket.
C. Tighten the screws firmly into the plastic
anchors.
6Connect all the necessary cables.
7Adjust the angle.
Template SheetTorx Wrench
Screw & Plastic Anchor - 3pcs Quick Manual
Safety Information Installation and Use Precautions
POWER
1. Use the power line after fixing it firmly to the power connection terminal.
Incomplete connection can cause a fire.
2. Do not extend the adapter output cable. If you need to install the power cable
extension, please contact the service center.
3. Use insulated power for PoE connected external power.
INSTALLATION
1. It is recommended not to touch the lens when installing the product as the factory
ships with a focus adjustment completed during the manufacturing completion
inspection phase.
2. Avoid installing cameras facing bright lights like sunlight. Causes damage to the
image sensor.
3. Make sure it safe and securely when installing camera on the wall or ceilling. This
can cause injury by the fall.
4. Do not connect multiple cameras to one adapter. Excess capacity causes abnormal
heat and fire.
5. Wear protective gloves when installing/uninstalling the camera. This causes burns
caused by high temperature on the surface of the product.
6. Don't drop or shock the product. Please stay away from places where vibration is
severe or magnet types are present.
7. Install it in a well-ventilated place. This can cause fire and failure.
CLEANING
1. Wipe the contaminated surface with a clean, soft, dry cloth or wet the soft, dry cloth
to prevent water from flowing, then wipe the contaminated area.
1. The battery (battery pack or equipped battery) must not be exposed to excessive
heat such as sunlight, fire, etc.
2. Do not disassemble the camera at your discretion.
3. If you forcefully install the product with excessive force, malfunction can damage
the camera.
4. Do not punch or shake the camera and be careful not to damage the camera with
careless storage or malfunction.
5. Be careful not to install the camera in a rainy or humid place, and do not leave it in a
wet place.
6. Installing or using the product in water can cause serious product failure.
7. Do not install the product if there is chemical or vapor in the place where the
product is installed, or if it can be generated.
8. Be careful not to get chemicals on the surface of the product when installing the
product. Chemical solvents such as cleaning agents and adhesive components can
cause fatal damage to the surface of the product.
9. Do not install it near the kitchen or cooking table as edible oil such as soybean oil
can also cause product damage and deformation. It can cause product damage.
10. Be careful not to get foreign substances on the Micro SD card terminal. If there is
any foreign substance, wipe it with a soft cloth.
11. Data will not be saved at the end of the life of the Micro SD card. In this case,
purchase a new Micro SD card.
12. Moisture may occur in the glass of the camera when the new product box is opened
(or when the product is initially running). The generated moisture is removed by a
Gore vent attached to the camera within hours of the power connection.
13. For products enclosed with a desiccant or card-type absorbent, please install it
according to the manual.
14. Use only with cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus.
15. Unplug this apparatus when a cart is used. Use caution when
moving the cart/apparatus combination to avoid injury from
tip-over.
WARNINGS : Serious injury or death may be caused
if any of these warnings are neglected.
BATTERY
1. There is a risk of explosion if the battery is incorrectly replaced. The battery should
be replaced only with the same battery.
2. Used batteries must be disposed of according to local regulations or battery
manufacturer's instructions. Disposing of in a fire or in a hot oven, or mechanically
crushing and cutting may cause an explosion.
3. Leaving the battery in a very high temperature or low air pressure environment may result
in an explosion or leak of flammable liquids or gases.
POWER
1. Use only standardized adapters written in the manual. Incorrect connection of the
power source can cause fire, electric shock, or failure.
2. If there is smoke or a strange smell from the power source, disconnect the power
immediately and contact the service center or purchasing office. If you continue to
use it as it is, it can cause fire and electric shock.
3. Disconnect the power plug from the outlet before connecting to the power terminal block.
INSTALLATION
1. Install it according to the temperature and humidity environment suitable for the
product specifications. Otherwise, it can cause fire and electric shock.
2. Thunder and lightning can cause problems with the camera. When installing, be
careful to minimize damage caused by lightning such as grounding.
3. Do not place conductive materials (drivers, coins, metal sticks, etc.) and water-filled
containers on the camera. It causes injuries caused by fire, electric shock, and falling.
4. If you want to move the installed product, turn off the power and move it or reinstall it.
Otherwise, it can cause fire and electric shock.
These instructions are intended to ensure that the user can use the product
correctly to avoid danger or property loss.
If the product is not functioning properly or damaged, contact the service center or
purchasing office.
CAUTIONS : Injury or equipment damage may be caused
if any of these cautions are eglected.
5. Do not install it in places where there is a lot of moisture, dust, soot, etc. It causes
fire and electric shock.
6. Avoid places where direct sunlight comes in or where heat comes out, such as
heating appliances. It causes fire and electric shock.
CLEANING
1. Do not spray water directly on each part of the product when cleaning. It causes fire
and electric shock.
CAUTION : Risk of explosion if battery is replaced by an incorrect type.
Dispose of used of used batteries according to the instructions.
ATTENTION : Il y a risque d'explosion si la batterie est remplaée par une batterie de type incorrect.
Mettre au rebut les batteries usagees conformément aux instructions.
Waterproof cap & Gasket
& Rubber 2ea
(Black : ø4 / White : ø5)
Note : Cable thickness 4.5ø to 5.5ø uses a black rubber, and over 5.5ø uses a white
rubber.
www.wavestore.com
WV-CT-4F
Wavestore Vision Thermal
Mini Bullet IP Camera
Quick Guide
1. Product & Accessories 2. Part Name 3. Installation
To disconnect power from the mains, pull out the mains cord plug. When install the product, ensure that
the plug is easily accessible.
Camera
Cables
Sunshield
Lens
RJ-45 Connector
BNC Cable
DC Power Jack
Audio, Sensor,
Alarm Cable
Waterproof Cap
Bracket
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the userwill be required to correct the interferenece at his own expense.
Before installing your camera, you have to read the following cautions.
1. You have to check whether the location can bear five times of the weight of your camera.
2. Don’t let the cable to be caught in improper place or the electric line cover to be damaged.
Otherwise it may cause a breakdown or fire.
3. When installing your camera, don’t allow any person to approach the installation site.
If you have any valuable things under the place, move them away.
Please check if all the camera and accessories are included in the package.
1Drill three holes on the installation
surface based on the provided
installation template.
2Insert the plastic anchors into the
holes.
3Install the provided ferrite core on the
cable.
4Attach the provided wall cushion to
the bottom of the camera’s pan/tilt
bracket.
5Fix the camera to the installation
surface.
A. Align the screw holes of the camera’s pan/
tilt bracket and the plastic anchors.
B. Insert the provided screw into the plastic
anchors through the screw holes of the
camera’s pan/tilt bracket.
C. Tighten the screws firmly into the plastic
anchors.
6Connect all the necessary cables.
7Adjust the angle.
Template SheetTorx Wrench
Screw & Plastic Anchor - 3pcs Quick Manual
Safety Information Installation and Use Precautions
POWER
1. Use the power line after fixing it firmly to the power connection terminal.
Incomplete connection can cause a fire.
2. Do not extend the adapter output cable. If you need to install the power cable
extension, please contact the service center.
3. Use insulated power for PoE connected external power.
INSTALLATION
1. It is recommended not to touch the lens when installing the product as the factory
ships with a focus adjustment completed during the manufacturing completion
inspection phase.
2. Avoid installing cameras facing bright lights like sunlight. Causes damage to the
image sensor.
3. Make sure it safe and securely when installing camera on the wall or ceilling. This
can cause injury by the fall.
4. Do not connect multiple cameras to one adapter. Excess capacity causes abnormal
heat and fire.
5. Wear protective gloves when installing/uninstalling the camera. This causes burns
caused by high temperature on the surface of the product.
6. Don't drop or shock the product. Please stay away from places where vibration is
severe or magnet types are present.
7. Install it in a well-ventilated place. This can cause fire and failure.
CLEANING
1. Wipe the contaminated surface with a clean, soft, dry cloth or wet the soft, dry cloth
to prevent water from flowing, then wipe the contaminated area.
1. The battery (battery pack or equipped battery) must not be exposed to excessive
heat such as sunlight, fire, etc.
2. Do not disassemble the camera at your discretion.
3. If you forcefully install the product with excessive force, malfunction can damage
the camera.
4. Do not punch or shake the camera and be careful not to damage the camera with
careless storage or malfunction.
5. Be careful not to install the camera in a rainy or humid place, and do not leave it in a
wet place.
6. Installing or using the product in water can cause serious product failure.
7. Do not install the product if there is chemical or vapor in the place where the
product is installed, or if it can be generated.
8. Be careful not to get chemicals on the surface of the product when installing the
product. Chemical solvents such as cleaning agents and adhesive components can
cause fatal damage to the surface of the product.
9. Do not install it near the kitchen or cooking table as edible oil such as soybean oil
can also cause product damage and deformation. It can cause product damage.
10. Be careful not to get foreign substances on the Micro SD card terminal. If there is
any foreign substance, wipe it with a soft cloth.
11. Data will not be saved at the end of the life of the Micro SD card. In this case,
purchase a new Micro SD card.
12. Moisture may occur in the glass of the camera when the new product box is opened
(or when the product is initially running). The generated moisture is removed by a
Gore vent attached to the camera within hours of the power connection.
13. For products enclosed with a desiccant or card-type absorbent, please install it
according to the manual.
14. Use only with cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus.
15. Unplug this apparatus when a cart is used. Use caution when
moving the cart/apparatus combination to avoid injury from
tip-over.
WARNINGS : Serious injury or death may be caused
if any of these warnings are neglected.
BATTERY
1. There is a risk of explosion if the battery is incorrectly replaced. The battery should
be replaced only with the same battery.
2. Used batteries must be disposed of according to local regulations or battery
manufacturer's instructions. Disposing of in a fire or in a hot oven, or mechanically
crushing and cutting may cause an explosion.
3. Leaving the battery in a very high temperature or low air pressure environment may result
in an explosion or leak of flammable liquids or gases.
POWER
1. Use only standardized adapters written in the manual. Incorrect connection of the
power source can cause fire, electric shock, or failure.
2. If there is smoke or a strange smell from the power source, disconnect the power
immediately and contact the service center or purchasing office. If you continue to
use it as it is, it can cause fire and electric shock.
3. Disconnect the power plug from the outlet before connecting to the power terminal block.
INSTALLATION
1. Install it according to the temperature and humidity environment suitable for the
product specifications. Otherwise, it can cause fire and electric shock.
2. Thunder and lightning can cause problems with the camera. When installing, be
careful to minimize damage caused by lightning such as grounding.
3. Do not place conductive materials (drivers, coins, metal sticks, etc.) and water-filled
containers on the camera. It causes injuries caused by fire, electric shock, and falling.
4. If you want to move the installed product, turn off the power and move it or reinstall it.
Otherwise, it can cause fire and electric shock.
These instructions are intended to ensure that the user can use the product
correctly to avoid danger or property loss.
If the product is not functioning properly or damaged, contact the service center or
purchasing office.
CAUTIONS : Injury or equipment damage may be caused
if any of these cautions are eglected.
5. Do not install it in places where there is a lot of moisture, dust, soot, etc. It causes
fire and electric shock.
6. Avoid places where direct sunlight comes in or where heat comes out, such as
heating appliances. It causes fire and electric shock.
CLEANING
1. Do not spray water directly on each part of the product when cleaning. It causes fire
and electric shock.
CAUTION : Risk of explosion if battery is replaced by an incorrect type.
Dispose of used of used batteries according to the instructions.
ATTENTION : Il y a risque d'explosion si la batterie est remplaée par une batterie de type incorrect.
Mettre au rebut les batteries usagees conformément aux instructions.
Waterproof cap & Gasket
& Rubber 2ea
(Black : ø4 / White : ø5)
Note : Cable thickness 4.5ø to 5.5ø uses a black rubber, and over 5.5ø uses a white
rubber.
www.wavestore.com
WV-CT-4F
Wavestore Vision Thermal
Mini Bullet IP Camera
Quick Guide
1. Product & Accessories 2. Part Name 3. Installation
To disconnect power from the mains, pull out the mains cord plug. When install the product, ensure that
the plug is easily accessible.
Camera
Cables
Sunshield
Lens
RJ-45 Connector
BNC Cable
DC Power Jack
Audio, Sensor,
Alarm Cable
Waterproof Cap
Bracket
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the userwill be required to correct the interferenece at his own expense.
Before installing your camera, you have to read the following cautions.
1. You have to check whether the location can bear five times of the weight of your camera.
2. Don’t let the cable to be caught in improper place or the electric line cover to be damaged.
Otherwise it may cause a breakdown or fire.
3. When installing your camera, don’t allow any person to approach the installation site.
If you have any valuable things under the place, move them away.
Please check if all the camera and accessories are included in the package.
1Drill three holes on the installation
surface based on the provided
installation template.
2Insert the plastic anchors into the
holes.
3Install the provided ferrite core on the
cable.
4Attach the provided wall cushion to
the bottom of the camera’s pan/tilt
bracket.
5Fix the camera to the installation
surface.
A. Align the screw holes of the camera’s pan/
tilt bracket and the plastic anchors.
B. Insert the provided screw into the plastic
anchors through the screw holes of the
camera’s pan/tilt bracket.
C. Tighten the screws firmly into the plastic
anchors.
6Connect all the necessary cables.
7Adjust the angle.
Template SheetTorx Wrench
Screw & Plastic Anchor - 3pcs Quick Manual
Safety Information Installation and Use Precautions
POWER
1. Use the power line after fixing it firmly to the power connection terminal.
Incomplete connection can cause a fire.
2. Do not extend the adapter output cable. If you need to install the power cable
extension, please contact the service center.
3. Use insulated power for PoE connected external power.
INSTALLATION
1. It is recommended not to touch the lens when installing the product as the factory
ships with a focus adjustment completed during the manufacturing completion
inspection phase.
2. Avoid installing cameras facing bright lights like sunlight. Causes damage to the
image sensor.
3. Make sure it safe and securely when installing camera on the wall or ceilling. This
can cause injury by the fall.
4. Do not connect multiple cameras to one adapter. Excess capacity causes abnormal
heat and fire.
5. Wear protective gloves when installing/uninstalling the camera. This causes burns
caused by high temperature on the surface of the product.
6. Don't drop or shock the product. Please stay away from places where vibration is
severe or magnet types are present.
7. Install it in a well-ventilated place. This can cause fire and failure.
CLEANING
1. Wipe the contaminated surface with a clean, soft, dry cloth or wet the soft, dry cloth
to prevent water from flowing, then wipe the contaminated area.
1. The battery (battery pack or equipped battery) must not be exposed to excessive
heat such as sunlight, fire, etc.
2. Do not disassemble the camera at your discretion.
3. If you forcefully install the product with excessive force, malfunction can damage
the camera.
4. Do not punch or shake the camera and be careful not to damage the camera with
careless storage or malfunction.
5. Be careful not to install the camera in a rainy or humid place, and do not leave it in a
wet place.
6. Installing or using the product in water can cause serious product failure.
7. Do not install the product if there is chemical or vapor in the place where the
product is installed, or if it can be generated.
8. Be careful not to get chemicals on the surface of the product when installing the
product. Chemical solvents such as cleaning agents and adhesive components can
cause fatal damage to the surface of the product.
9. Do not install it near the kitchen or cooking table as edible oil such as soybean oil
can also cause product damage and deformation. It can cause product damage.
10. Be careful not to get foreign substances on the Micro SD card terminal. If there is
any foreign substance, wipe it with a soft cloth.
11. Data will not be saved at the end of the life of the Micro SD card. In this case,
purchase a new Micro SD card.
12. Moisture may occur in the glass of the camera when the new product box is opened
(or when the product is initially running). The generated moisture is removed by a
Gore vent attached to the camera within hours of the power connection.
13. For products enclosed with a desiccant or card-type absorbent, please install it
according to the manual.
14. Use only with cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus.
15. Unplug this apparatus when a cart is used. Use caution when
moving the cart/apparatus combination to avoid injury from
tip-over.
WARNINGS : Serious injury or death may be caused
if any of these warnings are neglected.
BATTERY
1. There is a risk of explosion if the battery is incorrectly replaced. The battery should
be replaced only with the same battery.
2. Used batteries must be disposed of according to local regulations or battery
manufacturer's instructions. Disposing of in a fire or in a hot oven, or mechanically
crushing and cutting may cause an explosion.
3. Leaving the battery in a very high temperature or low air pressure environment may result
in an explosion or leak of flammable liquids or gases.
POWER
1. Use only standardized adapters written in the manual. Incorrect connection of the
power source can cause fire, electric shock, or failure.
2. If there is smoke or a strange smell from the power source, disconnect the power
immediately and contact the service center or purchasing office. If you continue to
use it as it is, it can cause fire and electric shock.
3. Disconnect the power plug from the outlet before connecting to the power terminal block.
INSTALLATION
1. Install it according to the temperature and humidity environment suitable for the
product specifications. Otherwise, it can cause fire and electric shock.
2. Thunder and lightning can cause problems with the camera. When installing, be
careful to minimize damage caused by lightning such as grounding.
3. Do not place conductive materials (drivers, coins, metal sticks, etc.) and water-filled
containers on the camera. It causes injuries caused by fire, electric shock, and falling.
4. If you want to move the installed product, turn off the power and move it or reinstall it.
Otherwise, it can cause fire and electric shock.
These instructions are intended to ensure that the user can use the product
correctly to avoid danger or property loss.
If the product is not functioning properly or damaged, contact the service center or
purchasing office.
CAUTIONS : Injury or equipment damage may be caused
if any of these cautions are eglected.
5. Do not install it in places where there is a lot of moisture, dust, soot, etc. It causes
fire and electric shock.
6. Avoid places where direct sunlight comes in or where heat comes out, such as
heating appliances. It causes fire and electric shock.
CLEANING
1. Do not spray water directly on each part of the product when cleaning. It causes fire
and electric shock.
CAUTION : Risk of explosion if battery is replaced by an incorrect type.
Dispose of used of used batteries according to the instructions.
ATTENTION : Il y a risque d'explosion si la batterie est remplaée par une batterie de type incorrect.
Mettre au rebut les batteries usagees conformément aux instructions.
Waterproof cap & Gasket
& Rubber 2ea
(Black : ø4 / White : ø5)
Note : Cable thickness 4.5ø to 5.5ø uses a black rubber, and over 5.5ø uses a white
rubber.
www.wavestore.com
WV-CT-4F
Wavestore Vision Thermal
Mini Bullet IP Camera
Quick Guide
1. Product & Accessories 2. Part Name 3. Installation
To disconnect power from the mains, pull out the mains cord plug. When install the product, ensure that
the plug is easily accessible.
Camera
Cables
Sunshield
Lens
RJ-45 Connector
BNC Cable
DC Power Jack
Audio, Sensor,
Alarm Cable
Waterproof Cap
Bracket
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the userwill be required to correct the interferenece at his own expense.
Before installing your camera, you have to read the following cautions.
1. You have to check whether the location can bear five times of the weight of your camera.
2. Don’t let the cable to be caught in improper place or the electric line cover to be damaged.
Otherwise it may cause a breakdown or fire.
3. When installing your camera, don’t allow any person to approach the installation site.
If you have any valuable things under the place, move them away.
Please check if all the camera and accessories are included in the package.
1Drill three holes on the installation
surface based on the provided
installation template.
2Insert the plastic anchors into the
holes.
3Install the provided ferrite core on the
cable.
4Attach the provided wall cushion to
the bottom of the camera’s pan/tilt
bracket.
5Fix the camera to the installation
surface.
A. Align the screw holes of the camera’s pan/
tilt bracket and the plastic anchors.
B. Insert the provided screw into the plastic
anchors through the screw holes of the
camera’s pan/tilt bracket.
C. Tighten the screws firmly into the plastic
anchors.
6Connect all the necessary cables.
7Adjust the angle.
Template SheetTorx Wrench
Screw & Plastic Anchor - 3pcs Quick Manual
Safety Information Installation and Use Precautions
POWER
1. Use the power line after fixing it firmly to the power connection terminal.
Incomplete connection can cause a fire.
2. Do not extend the adapter output cable. If you need to install the power cable
extension, please contact the service center.
3. Use insulated power for PoE connected external power.
INSTALLATION
1. It is recommended not to touch the lens when installing the product as the factory
ships with a focus adjustment completed during the manufacturing completion
inspection phase.
2. Avoid installing cameras facing bright lights like sunlight. Causes damage to the
image sensor.
3. Make sure it safe and securely when installing camera on the wall or ceilling. This
can cause injury by the fall.
4. Do not connect multiple cameras to one adapter. Excess capacity causes abnormal
heat and fire.
5. Wear protective gloves when installing/uninstalling the camera. This causes burns
caused by high temperature on the surface of the product.
6. Don't drop or shock the product. Please stay away from places where vibration is
severe or magnet types are present.
7. Install it in a well-ventilated place. This can cause fire and failure.
CLEANING
1. Wipe the contaminated surface with a clean, soft, dry cloth or wet the soft, dry cloth
to prevent water from flowing, then wipe the contaminated area.
1. The battery (battery pack or equipped battery) must not be exposed to excessive
heat such as sunlight, fire, etc.
2. Do not disassemble the camera at your discretion.
3. If you forcefully install the product with excessive force, malfunction can damage
the camera.
4. Do not punch or shake the camera and be careful not to damage the camera with
careless storage or malfunction.
5. Be careful not to install the camera in a rainy or humid place, and do not leave it in a
wet place.
6. Installing or using the product in water can cause serious product failure.
7. Do not install the product if there is chemical or vapor in the place where the
product is installed, or if it can be generated.
8. Be careful not to get chemicals on the surface of the product when installing the
product. Chemical solvents such as cleaning agents and adhesive components can
cause fatal damage to the surface of the product.
9. Do not install it near the kitchen or cooking table as edible oil such as soybean oil
can also cause product damage and deformation. It can cause product damage.
10. Be careful not to get foreign substances on the Micro SD card terminal. If there is
any foreign substance, wipe it with a soft cloth.
11. Data will not be saved at the end of the life of the Micro SD card. In this case,
purchase a new Micro SD card.
12. Moisture may occur in the glass of the camera when the new product box is opened
(or when the product is initially running). The generated moisture is removed by a
Gore vent attached to the camera within hours of the power connection.
13. For products enclosed with a desiccant or card-type absorbent, please install it
according to the manual.
14. Use only with cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus.
15. Unplug this apparatus when a cart is used. Use caution when
moving the cart/apparatus combination to avoid injury from
tip-over.
WARNINGS : Serious injury or death may be caused
if any of these warnings are neglected.
BATTERY
1. There is a risk of explosion if the battery is incorrectly replaced. The battery should
be replaced only with the same battery.
2. Used batteries must be disposed of according to local regulations or battery
manufacturer's instructions. Disposing of in a fire or in a hot oven, or mechanically
crushing and cutting may cause an explosion.
3. Leaving the battery in a very high temperature or low air pressure environment may result
in an explosion or leak of flammable liquids or gases.
POWER
1. Use only standardized adapters written in the manual. Incorrect connection of the
power source can cause fire, electric shock, or failure.
2. If there is smoke or a strange smell from the power source, disconnect the power
immediately and contact the service center or purchasing office. If you continue to
use it as it is, it can cause fire and electric shock.
3. Disconnect the power plug from the outlet before connecting to the power terminal block.
INSTALLATION
1. Install it according to the temperature and humidity environment suitable for the
product specifications. Otherwise, it can cause fire and electric shock.
2. Thunder and lightning can cause problems with the camera. When installing, be
careful to minimize damage caused by lightning such as grounding.
3. Do not place conductive materials (drivers, coins, metal sticks, etc.) and water-filled
containers on the camera. It causes injuries caused by fire, electric shock, and falling.
4. If you want to move the installed product, turn off the power and move it or reinstall it.
Otherwise, it can cause fire and electric shock.
These instructions are intended to ensure that the user can use the product
correctly to avoid danger or property loss.
If the product is not functioning properly or damaged, contact the service center or
purchasing office.
CAUTIONS : Injury or equipment damage may be caused
if any of these cautions are eglected.
5. Do not install it in places where there is a lot of moisture, dust, soot, etc. It causes
fire and electric shock.
6. Avoid places where direct sunlight comes in or where heat comes out, such as
heating appliances. It causes fire and electric shock.
CLEANING
1. Do not spray water directly on each part of the product when cleaning. It causes fire
and electric shock.
CAUTION : Risk of explosion if battery is replaced by an incorrect type.
Dispose of used of used batteries according to the instructions.
ATTENTION : Il y a risque d'explosion si la batterie est remplaée par une batterie de type incorrect.
Mettre au rebut les batteries usagees conformément aux instructions.
Waterproof cap & Gasket
& Rubber 2ea
(Black : ø4 / White : ø5)
Note : Cable thickness 4.5ø to 5.5ø uses a black rubber, and over 5.5ø uses a white
rubber.
www.wavestore.com
WV-CT-4F
Wavestore Vision Thermal
Mini Bullet IP Camera
Quick Guide
1. Product & Accessories 2. Part Name 3. Installation
To disconnect power from the mains, pull out the mains cord plug. When install the product, ensure that
the plug is easily accessible.
Camera
Cables
Sunshield
Lens
RJ-45 Connector
BNC Cable
DC Power Jack
Audio, Sensor,
Alarm Cable
Waterproof Cap
Bracket
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the userwill be required to correct the interferenece at his own expense.
Before installing your camera, you have to read the following cautions.
1. You have to check whether the location can bear five times of the weight of your camera.
2. Don’t let the cable to be caught in improper place or the electric line cover to be damaged.
Otherwise it may cause a breakdown or fire.
3. When installing your camera, don’t allow any person to approach the installation site.
If you have any valuable things under the place, move them away.
Please check if all the camera and accessories are included in the package.
1Drill three holes on the installation
surface based on the provided
installation template.
2Insert the plastic anchors into the
holes.
3Install the provided ferrite core on the
cable.
4Attach the provided wall cushion to
the bottom of the camera’s pan/tilt
bracket.
5Fix the camera to the installation
surface.
A. Align the screw holes of the camera’s pan/
tilt bracket and the plastic anchors.
B. Insert the provided screw into the plastic
anchors through the screw holes of the
camera’s pan/tilt bracket.
C. Tighten the screws firmly into the plastic
anchors.
6Connect all the necessary cables.
7Adjust the angle.
Template SheetTorx Wrench
Screw & Plastic Anchor - 3pcs Quick Manual
Safety Information Installation and Use Precautions
POWER
1. Use the power line after fixing it firmly to the power connection terminal.
Incomplete connection can cause a fire.
2. Do not extend the adapter output cable. If you need to install the power cable
extension, please contact the service center.
3. Use insulated power for PoE connected external power.
INSTALLATION
1. It is recommended not to touch the lens when installing the product as the factory
ships with a focus adjustment completed during the manufacturing completion
inspection phase.
2. Avoid installing cameras facing bright lights like sunlight. Causes damage to the
image sensor.
3. Make sure it safe and securely when installing camera on the wall or ceilling. This
can cause injury by the fall.
4. Do not connect multiple cameras to one adapter. Excess capacity causes abnormal
heat and fire.
5. Wear protective gloves when installing/uninstalling the camera. This causes burns
caused by high temperature on the surface of the product.
6. Don't drop or shock the product. Please stay away from places where vibration is
severe or magnet types are present.
7. Install it in a well-ventilated place. This can cause fire and failure.
CLEANING
1. Wipe the contaminated surface with a clean, soft, dry cloth or wet the soft, dry cloth
to prevent water from flowing, then wipe the contaminated area.
1. The battery (battery pack or equipped battery) must not be exposed to excessive
heat such as sunlight, fire, etc.
2. Do not disassemble the camera at your discretion.
3. If you forcefully install the product with excessive force, malfunction can damage
the camera.
4. Do not punch or shake the camera and be careful not to damage the camera with
careless storage or malfunction.
5. Be careful not to install the camera in a rainy or humid place, and do not leave it in a
wet place.
6. Installing or using the product in water can cause serious product failure.
7. Do not install the product if there is chemical or vapor in the place where the
product is installed, or if it can be generated.
8. Be careful not to get chemicals on the surface of the product when installing the
product. Chemical solvents such as cleaning agents and adhesive components can
cause fatal damage to the surface of the product.
9. Do not install it near the kitchen or cooking table as edible oil such as soybean oil
can also cause product damage and deformation. It can cause product damage.
10. Be careful not to get foreign substances on the Micro SD card terminal. If there is
any foreign substance, wipe it with a soft cloth.
11. Data will not be saved at the end of the life of the Micro SD card. In this case,
purchase a new Micro SD card.
12. Moisture may occur in the glass of the camera when the new product box is opened
(or when the product is initially running). The generated moisture is removed by a
Gore vent attached to the camera within hours of the power connection.
13. For products enclosed with a desiccant or card-type absorbent, please install it
according to the manual.
14. Use only with cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus.
15. Unplug this apparatus when a cart is used. Use caution when
moving the cart/apparatus combination to avoid injury from
tip-over.
WARNINGS : Serious injury or death may be caused
if any of these warnings are neglected.
BATTERY
1. There is a risk of explosion if the battery is incorrectly replaced. The battery should
be replaced only with the same battery.
2. Used batteries must be disposed of according to local regulations or battery
manufacturer's instructions. Disposing of in a fire or in a hot oven, or mechanically
crushing and cutting may cause an explosion.
3. Leaving the battery in a very high temperature or low air pressure environment may result
in an explosion or leak of flammable liquids or gases.
POWER
1. Use only standardized adapters written in the manual. Incorrect connection of the
power source can cause fire, electric shock, or failure.
2. If there is smoke or a strange smell from the power source, disconnect the power
immediately and contact the service center or purchasing office. If you continue to
use it as it is, it can cause fire and electric shock.
3. Disconnect the power plug from the outlet before connecting to the power terminal block.
INSTALLATION
1. Install it according to the temperature and humidity environment suitable for the
product specifications. Otherwise, it can cause fire and electric shock.
2. Thunder and lightning can cause problems with the camera. When installing, be
careful to minimize damage caused by lightning such as grounding.
3. Do not place conductive materials (drivers, coins, metal sticks, etc.) and water-filled
containers on the camera. It causes injuries caused by fire, electric shock, and falling.
4. If you want to move the installed product, turn off the power and move it or reinstall it.
Otherwise, it can cause fire and electric shock.
These instructions are intended to ensure that the user can use the product
correctly to avoid danger or property loss.
If the product is not functioning properly or damaged, contact the service center or
purchasing office.
CAUTIONS : Injury or equipment damage may be caused
if any of these cautions are eglected.
5. Do not install it in places where there is a lot of moisture, dust, soot, etc. It causes
fire and electric shock.
6. Avoid places where direct sunlight comes in or where heat comes out, such as
heating appliances. It causes fire and electric shock.
CLEANING
1. Do not spray water directly on each part of the product when cleaning. It causes fire
and electric shock.
CAUTION : Risk of explosion if battery is replaced by an incorrect type.
Dispose of used of used batteries according to the instructions.
ATTENTION : Il y a risque d'explosion si la batterie est remplaée par une batterie de type incorrect.
Mettre au rebut les batteries usagees conformément aux instructions.
Waterproof cap & Gasket
& Rubber 2ea
(Black : ø4 / White : ø5)
Note : Cable thickness 4.5ø to 5.5ø uses a black rubber, and over 5.5ø uses a white
rubber.
www.wavestore.com
5. IP Installer
4. Cabling
1Power Connection
Please, check the voltage and current
capacity of rated power carefully.
2Network Connection
Connect the crossover cable into the
RJ-45.
3BNC Connection
Used to connect video output device
such as monitor using the BNC coaxial
cable.
4Audio In
Connect the ‘Audio In’ cable of the
camera to the device like microphone.
5Audio Out
Connect the ‘Audio Out’ cable of the
camera to device like speaker.
Audio Out supports only RTSP Back
channel function. It plans to make it
available on the web later.
6Alarm In
Cable of the sensor/alarm input device
should connect to Yellow and Sky
Green line of the Alam cable.
7Alarm Out
It connects to the alarm lights, siren or
lamps and the sensor types are normal
open and normal close.
Cable of the alarm output device
should connect to DO1(N.O.) and DO1
COM of the cable slot.
1Power
2Network
3BNC
4Audio In
5Audio Out
7Alarm In
6Alarm In
Rate Power Power
Consumption PoE
DC 12V 11.9W IEEE 802.3af class3
AUDIO IN : PINK
AUDIO GND : PINK + DOT
AUDIO OUT : SKYBLUE
DI : SKY GREEN
DI COM : YELLOW
DO1 (N.O) : GREEN
DO1 COM : YELLOW + DOT
Preparing to Mount the Camera
1. The mounting surface must bear five times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line cover to be
damaged. This may cause a breakdown or fire.
3. CAUTION: These servicing instructions are for use by qualified service personnel
only. To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.
4. This product is intended to be supplied by a UL Listed Power Supply Unit marked
“Class 2” or “LPS” or “PS2” and rated 12 Vdc, 1A min or PoE (802.3af), 0.32A.
5. The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE
802.3af shall be a UL Listed device with the output evaluated as a Limited Power
Source as defined in UL60950-1 or PS2 as defined in UL62368-1.
6. Unit is intended for installation in a Network Environment 0 as defined in IEC TR
62102. As such, associated Ethernet wiring shall be limited to inside the building.
7. Using the mounting template sheet or the camera itself, mark and drill the necessary
holes in the wall or ceiling.
Disposal of Old Appliance
1. The symbol marked in the product, will follow and covered by the
Europe Directive 2002/95/EC.
2. All electornic disposal of waste is differenct by the government or
locally, so so it need to check.
3. The correct disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance,
please contact your city office, waste disposal service or the shop
where you purchased the product.
How to connect to the network
through the water proof cable
Insert the Lan cable into the rubber
first as (a) below. Put the Lan cable
into (b), then (c) will be assembled to
(b) tightly. As a final step, (d) need to
be assembled to (c) without making
any space.
1. Using a PoE-Enabled Switch
The Camera is PoE-compliant, allowing
transmission of power and data via a single
Ethernet cable.
PoE eliminates the need for the different
cables used to power, record, or control
the camera.
Follow the illustration below to connect
the camera to a PoE-enabled switch using
an Ethernet cable.
2. Using a Non-PoE Switch
If a PoE-enabled switch is not used, use a
power adaptor for power transmission and
non-PoE switch for data transmission.
Follow the illustrations below to connect
the camera without a PoE-enabled Switch.
Two Options
Use a PoE-enabled swtich to connect data and power through a single cable and begin
viewing and recording images instantly. A non-PoE switch will require an adaptor for power
transmission.
Ethernet Cable Ethernet Cable
Power
b
ac
d
2
4
3
5
7
8
9
6
10
12
11
1. Run IP Installer
1Run the IP installer.
2Click on Network Adaptor selection
Menu (NIC) after run this program.
3Select a network which a camera is
connected then click on a ‘Search’
button. (Takes about 5 sec.)
4Select a camera to set.
5The information of the selected
camera will be shown at Device Info.
6Select the network type.
iThe default network type of the
camera is STATIC.
iWhen set to DHCP, if you have a DHCP
server, it will automatically set the
Camera IP.
iWhen set to DHCP, if you do not have
a DHCP server, Camera IP is set to
192.168.xxx.xxx after one minute.
7Convert the device's MAC address to
the IP address.
The MAC Address of the device is
attached on the Product label.
Input IP setting information when the
network type is set to STATIC.
8Change the port as necessary when
the network type is set to STATIC.
9Input ID and PW of the camera for
authentication.
Make sure to change the ID and PW for
security reason.
Go to “Web viewer>Setup>System>
Users Management” for ID and PW
change.
The ID and PW will be set to default value
when ‘factory reset’ the camera.
10 Make sure to click on ‘Save’ button to
save changed values.
An “Apply” message will be popped-up
when the settings are applied normally,
or an error message will be popped-up
when failed.
11 To reboot or reset (except network
setting) the camera.
Select a camera (multiple camera can be
selected) > Input ID and PW > Click on
Reboot or Factory Reset button.
12 Able to delete an Active-X which is
installed when accessing to Web
Viewer.
You don’t need the function because this
camera use the VLC plugin instead of the
Active-X.
iA ‘Port Forwarding’ has to be set for
external access to the camera.
iRefer to the manual of the network hub
for ‘Port Forwarding’ settings.
iAn additional change of HTTPS, RTSP
port can be done at Web Viewer >
Admin page.
iDefault TCP/IP information
- IP: 192.168.xxx.xxx
- Subnet Mask: 255.255.0.0
- Gateway: 192.168.0.1
- DNS : 168.126.63.1
iDefault ID / PW : root / pass
iCovert the last two sets of hexadecimal
numbers to decimal numbers.
MAC address = 00-13-23-01-14-B1
IP address =192.168.20.177
Wavestore Vision Thermal Mini Bullet IP Camera Quick Guide
Visit: wavestore.com
Specications may change without notice.
GLOBAL HQ (EMEA)
Wavestore Global Ltd.
Tel: +44 (0) 1895 527 127
USA/CANADA
Wavestore Americas Inc.
Toll-free: 855-526-8887
MIDDLE EAST
Wavestore Middle East
Tel: +971 (4)881 2903
5. IP Installer
4. Cabling
1Power Connection
Please, check the voltage and current
capacity of rated power carefully.
2Network Connection
Connect the crossover cable into the
RJ-45.
3BNC Connection
Used to connect video output device
such as monitor using the BNC coaxial
cable.
4Audio In
Connect the ‘Audio In’ cable of the
camera to the device like microphone.
5Audio Out
Connect the ‘Audio Out’ cable of the
camera to device like speaker.
Audio Out supports only RTSP Back
channel function. It plans to make it
available on the web later.
6Alarm In
Cable of the sensor/alarm input device
should connect to Yellow and Sky
Green line of the Alam cable.
7Alarm Out
It connects to the alarm lights, siren or
lamps and the sensor types are normal
open and normal close.
Cable of the alarm output device
should connect to DO1(N.O.) and DO1
COM of the cable slot.
1Power
2Network
3BNC
4Audio In
5Audio Out
7Alarm In
6Alarm In
Rate Power Power
Consumption PoE
DC 12V 11.9W IEEE 802.3af class3
AUDIO IN : PINK
AUDIO GND : PINK + DOT
AUDIO OUT : SKYBLUE
DI : SKY GREEN
DI COM : YELLOW
DO1 (N.O) : GREEN
DO1 COM : YELLOW + DOT
Preparing to Mount the Camera
1. The mounting surface must bear five times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line cover to be
damaged. This may cause a breakdown or fire.
3. CAUTION: These servicing instructions are for use by qualified service personnel
only. To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.
4. This product is intended to be supplied by a UL Listed Power Supply Unit marked
“Class 2” or “LPS” or “PS2” and rated 12 Vdc, 1A min or PoE (802.3af), 0.32A.
5. The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE
802.3af shall be a UL Listed device with the output evaluated as a Limited Power
Source as defined in UL60950-1 or PS2 as defined in UL62368-1.
6. Unit is intended for installation in a Network Environment 0 as defined in IEC TR
62102. As such, associated Ethernet wiring shall be limited to inside the building.
7. Using the mounting template sheet or the camera itself, mark and drill the necessary
holes in the wall or ceiling.
Disposal of Old Appliance
1. The symbol marked in the product, will follow and covered by the
Europe Directive 2002/95/EC.
2. All electornic disposal of waste is differenct by the government or
locally, so so it need to check.
3. The correct disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance,
please contact your city office, waste disposal service or the shop
where you purchased the product.
How to connect to the network
through the water proof cable
Insert the Lan cable into the rubber
first as (a) below. Put the Lan cable
into (b), then (c) will be assembled to
(b) tightly. As a final step, (d) need to
be assembled to (c) without making
any space.
1. Using a PoE-Enabled Switch
The Camera is PoE-compliant, allowing
transmission of power and data via a single
Ethernet cable.
PoE eliminates the need for the different
cables used to power, record, or control
the camera.
Follow the illustration below to connect
the camera to a PoE-enabled switch using
an Ethernet cable.
2. Using a Non-PoE Switch
If a PoE-enabled switch is not used, use a
power adaptor for power transmission and
non-PoE switch for data transmission.
Follow the illustrations below to connect
the camera without a PoE-enabled Switch.
Two Options
Use a PoE-enabled swtich to connect data and power through a single cable and begin
viewing and recording images instantly. A non-PoE switch will require an adaptor for power
transmission.
Ethernet Cable Ethernet Cable
Power
b
ac
d
2
4
3
5
7
8
9
6
10
12
11
1. Run IP Installer
1Run the IP installer.
2Click on Network Adaptor selection
Menu (NIC) after run this program.
3Select a network which a camera is
connected then click on a ‘Search’
button. (Takes about 5 sec.)
4Select a camera to set.
5The information of the selected
camera will be shown at Device Info.
6Select the network type.
iThe default network type of the
camera is STATIC.
iWhen set to DHCP, if you have a DHCP
server, it will automatically set the
Camera IP.
iWhen set to DHCP, if you do not have
a DHCP server, Camera IP is set to
192.168.xxx.xxx after one minute.
7Convert the device's MAC address to
the IP address.
The MAC Address of the device is
attached on the Product label.
Input IP setting information when the
network type is set to STATIC.
8Change the port as necessary when
the network type is set to STATIC.
9Input ID and PW of the camera for
authentication.
Make sure to change the ID and PW for
security reason.
Go to “Web viewer>Setup>System>
Users Management” for ID and PW
change.
The ID and PW will be set to default value
when ‘factory reset’ the camera.
10 Make sure to click on ‘Save’ button to
save changed values.
An “Apply” message will be popped-up
when the settings are applied normally,
or an error message will be popped-up
when failed.
11 To reboot or reset (except network
setting) the camera.
Select a camera (multiple camera can be
selected) > Input ID and PW > Click on
Reboot or Factory Reset button.
12 Able to delete an Active-X which is
installed when accessing to Web
Viewer.
You don’t need the function because this
camera use the VLC plugin instead of the
Active-X.
iA ‘Port Forwarding’ has to be set for
external access to the camera.
iRefer to the manual of the network hub
for ‘Port Forwarding’ settings.
iAn additional change of HTTPS, RTSP
port can be done at Web Viewer >
Admin page.
iDefault TCP/IP information
- IP: 192.168.xxx.xxx
- Subnet Mask: 255.255.0.0
- Gateway: 192.168.0.1
- DNS : 168.126.63.1
iDefault ID / PW : root / pass
iCovert the last two sets of hexadecimal
numbers to decimal numbers.
MAC address = 00-13-23-01-14-B1
IP address =192.168.20.177
Wavestore Vision Thermal Mini Bullet IP Camera Quick Guide
Visit: wavestore.com
Specications may change without notice.
GLOBAL HQ (EMEA)
Wavestore Global Ltd.
Tel: +44 (0) 1895 527 127
USA/CANADA
Wavestore Americas Inc.
Toll-free: 855-526-8887
MIDDLE EAST
Wavestore Middle East
Tel: +971 (4)881 2903
5. IP Installer
4. Cabling
1Power Connection
Please, check the voltage and current
capacity of rated power carefully.
2Network Connection
Connect the crossover cable into the
RJ-45.
3BNC Connection
Used to connect video output device
such as monitor using the BNC coaxial
cable.
4Audio In
Connect the ‘Audio In’ cable of the
camera to the device like microphone.
5Audio Out
Connect the ‘Audio Out’ cable of the
camera to device like speaker.
Audio Out supports only RTSP Back
channel function. It plans to make it
available on the web later.
6Alarm In
Cable of the sensor/alarm input device
should connect to Yellow and Sky
Green line of the Alam cable.
7Alarm Out
It connects to the alarm lights, siren or
lamps and the sensor types are normal
open and normal close.
Cable of the alarm output device
should connect to DO1(N.O.) and DO1
COM of the cable slot.
1Power
2Network
3BNC
4Audio In
5Audio Out
7Alarm In
6Alarm In
Rate Power Power
Consumption PoE
DC 12V 11.9W IEEE 802.3af class3
AUDIO IN : PINK
AUDIO GND : PINK + DOT
AUDIO OUT : SKYBLUE
DI : SKY GREEN
DI COM : YELLOW
DO1 (N.O) : GREEN
DO1 COM : YELLOW + DOT
Preparing to Mount the Camera
1. The mounting surface must bear five times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line cover to be
damaged. This may cause a breakdown or fire.
3. CAUTION: These servicing instructions are for use by qualified service personnel
only. To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.
4. This product is intended to be supplied by a UL Listed Power Supply Unit marked
“Class 2” or “LPS” or “PS2” and rated 12 Vdc, 1A min or PoE (802.3af), 0.32A.
5. The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE
802.3af shall be a UL Listed device with the output evaluated as a Limited Power
Source as defined in UL60950-1 or PS2 as defined in UL62368-1.
6. Unit is intended for installation in a Network Environment 0 as defined in IEC TR
62102. As such, associated Ethernet wiring shall be limited to inside the building.
7. Using the mounting template sheet or the camera itself, mark and drill the necessary
holes in the wall or ceiling.
Disposal of Old Appliance
1. The symbol marked in the product, will follow and covered by the
Europe Directive 2002/95/EC.
2. All electornic disposal of waste is differenct by the government or
locally, so so it need to check.
3. The correct disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance,
please contact your city office, waste disposal service or the shop
where you purchased the product.
How to connect to the network
through the water proof cable
Insert the Lan cable into the rubber
first as (a) below. Put the Lan cable
into (b), then (c) will be assembled to
(b) tightly. As a final step, (d) need to
be assembled to (c) without making
any space.
1. Using a PoE-Enabled Switch
The Camera is PoE-compliant, allowing
transmission of power and data via a single
Ethernet cable.
PoE eliminates the need for the different
cables used to power, record, or control
the camera.
Follow the illustration below to connect
the camera to a PoE-enabled switch using
an Ethernet cable.
2. Using a Non-PoE Switch
If a PoE-enabled switch is not used, use a
power adaptor for power transmission and
non-PoE switch for data transmission.
Follow the illustrations below to connect
the camera without a PoE-enabled Switch.
Two Options
Use a PoE-enabled swtich to connect data and power through a single cable and begin
viewing and recording images instantly. A non-PoE switch will require an adaptor for power
transmission.
Ethernet Cable Ethernet Cable
Power
b
ac
d
2
4
3
5
7
8
9
6
10
12
11
1. Run IP Installer
1Run the IP installer.
2Click on Network Adaptor selection
Menu (NIC) after run this program.
3Select a network which a camera is
connected then click on a ‘Search’
button. (Takes about 5 sec.)
4Select a camera to set.
5The information of the selected
camera will be shown at Device Info.
6Select the network type.
iThe default network type of the
camera is STATIC.
iWhen set to DHCP, if you have a DHCP
server, it will automatically set the
Camera IP.
iWhen set to DHCP, if you do not have
a DHCP server, Camera IP is set to
192.168.xxx.xxx after one minute.
7Convert the device's MAC address to
the IP address.
The MAC Address of the device is
attached on the Product label.
Input IP setting information when the
network type is set to STATIC.
8Change the port as necessary when
the network type is set to STATIC.
9Input ID and PW of the camera for
authentication.
Make sure to change the ID and PW for
security reason.
Go to “Web viewer>Setup>System>
Users Management” for ID and PW
change.
The ID and PW will be set to default value
when ‘factory reset’ the camera.
10 Make sure to click on ‘Save’ button to
save changed values.
An “Apply” message will be popped-up
when the settings are applied normally,
or an error message will be popped-up
when failed.
11 To reboot or reset (except network
setting) the camera.
Select a camera (multiple camera can be
selected) > Input ID and PW > Click on
Reboot or Factory Reset button.
12 Able to delete an Active-X which is
installed when accessing to Web
Viewer.
You don’t need the function because this
camera use the VLC plugin instead of the
Active-X.
iA ‘Port Forwarding’ has to be set for
external access to the camera.
iRefer to the manual of the network hub
for ‘Port Forwarding’ settings.
iAn additional change of HTTPS, RTSP
port can be done at Web Viewer >
Admin page.
iDefault TCP/IP information
- IP: 192.168.xxx.xxx
- Subnet Mask: 255.255.0.0
- Gateway: 192.168.0.1
- DNS : 168.126.63.1
iDefault ID / PW : root / pass
iCovert the last two sets of hexadecimal
numbers to decimal numbers.
MAC address = 00-13-23-01-14-B1
IP address =192.168.20.177
Wavestore Vision Thermal Mini Bullet IP Camera Quick Guide
Visit: wavestore.com
Specications may change without notice.
GLOBAL HQ (EMEA)
Wavestore Global Ltd.
Tel: +44 (0) 1895 527 127
USA/CANADA
Wavestore Americas Inc.
Toll-free: 855-526-8887
MIDDLE EAST
Wavestore Middle East
Tel: +971 (4)881 2903
5. IP Installer
4. Cabling
1Power Connection
Please, check the voltage and current
capacity of rated power carefully.
2Network Connection
Connect the crossover cable into the
RJ-45.
3BNC Connection
Used to connect video output device
such as monitor using the BNC coaxial
cable.
4Audio In
Connect the ‘Audio In’ cable of the
camera to the device like microphone.
5Audio Out
Connect the ‘Audio Out’ cable of the
camera to device like speaker.
Audio Out supports only RTSP Back
channel function. It plans to make it
available on the web later.
6Alarm In
Cable of the sensor/alarm input device
should connect to Yellow and Sky
Green line of the Alam cable.
7Alarm Out
It connects to the alarm lights, siren or
lamps and the sensor types are normal
open and normal close.
Cable of the alarm output device
should connect to DO1(N.O.) and DO1
COM of the cable slot.
1Power
2Network
3BNC
4Audio In
5Audio Out
7Alarm In
6Alarm In
Rate Power Power
Consumption PoE
DC 12V 11.9W IEEE 802.3af class3
AUDIO IN : PINK
AUDIO GND : PINK + DOT
AUDIO OUT : SKYBLUE
DI : SKY GREEN
DI COM : YELLOW
DO1 (N.O) : GREEN
DO1 COM : YELLOW + DOT
Preparing to Mount the Camera
1. The mounting surface must bear five times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line cover to be
damaged. This may cause a breakdown or fire.
3. CAUTION: These servicing instructions are for use by qualified service personnel
only. To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.
4. This product is intended to be supplied by a UL Listed Power Supply Unit marked
“Class 2” or “LPS” or “PS2” and rated 12 Vdc, 1A min or PoE (802.3af), 0.32A.
5. The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE
802.3af shall be a UL Listed device with the output evaluated as a Limited Power
Source as defined in UL60950-1 or PS2 as defined in UL62368-1.
6. Unit is intended for installation in a Network Environment 0 as defined in IEC TR
62102. As such, associated Ethernet wiring shall be limited to inside the building.
7. Using the mounting template sheet or the camera itself, mark and drill the necessary
holes in the wall or ceiling.
Disposal of Old Appliance
1. The symbol marked in the product, will follow and covered by the
Europe Directive 2002/95/EC.
2. All electornic disposal of waste is differenct by the government or
locally, so so it need to check.
3. The correct disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance,
please contact your city office, waste disposal service or the shop
where you purchased the product.
How to connect to the network
through the water proof cable
Insert the Lan cable into the rubber
first as (a) below. Put the Lan cable
into (b), then (c) will be assembled to
(b) tightly. As a final step, (d) need to
be assembled to (c) without making
any space.
1. Using a PoE-Enabled Switch
The Camera is PoE-compliant, allowing
transmission of power and data via a single
Ethernet cable.
PoE eliminates the need for the different
cables used to power, record, or control
the camera.
Follow the illustration below to connect
the camera to a PoE-enabled switch using
an Ethernet cable.
2. Using a Non-PoE Switch
If a PoE-enabled switch is not used, use a
power adaptor for power transmission and
non-PoE switch for data transmission.
Follow the illustrations below to connect
the camera without a PoE-enabled Switch.
Two Options
Use a PoE-enabled swtich to connect data and power through a single cable and begin
viewing and recording images instantly. A non-PoE switch will require an adaptor for power
transmission.
Ethernet Cable Ethernet Cable
Power
b
ac
d
2
4
3
5
7
8
9
6
10
12
11
1. Run IP Installer
1Run the IP installer.
2Click on Network Adaptor selection
Menu (NIC) after run this program.
3Select a network which a camera is
connected then click on a ‘Search’
button. (Takes about 5 sec.)
4Select a camera to set.
5The information of the selected
camera will be shown at Device Info.
6Select the network type.
iThe default network type of the
camera is STATIC.
iWhen set to DHCP, if you have a DHCP
server, it will automatically set the
Camera IP.
iWhen set to DHCP, if you do not have
a DHCP server, Camera IP is set to
192.168.xxx.xxx after one minute.
7Convert the device's MAC address to
the IP address.
The MAC Address of the device is
attached on the Product label.
Input IP setting information when the
network type is set to STATIC.
8Change the port as necessary when
the network type is set to STATIC.
9Input ID and PW of the camera for
authentication.
Make sure to change the ID and PW for
security reason.
Go to “Web viewer>Setup>System>
Users Management” for ID and PW
change.
The ID and PW will be set to default value
when ‘factory reset’ the camera.
10 Make sure to click on ‘Save’ button to
save changed values.
An “Apply” message will be popped-up
when the settings are applied normally,
or an error message will be popped-up
when failed.
11 To reboot or reset (except network
setting) the camera.
Select a camera (multiple camera can be
selected) > Input ID and PW > Click on
Reboot or Factory Reset button.
12 Able to delete an Active-X which is
installed when accessing to Web
Viewer.
You don’t need the function because this
camera use the VLC plugin instead of the
Active-X.
iA ‘Port Forwarding’ has to be set for
external access to the camera.
iRefer to the manual of the network hub
for ‘Port Forwarding’ settings.
iAn additional change of HTTPS, RTSP
port can be done at Web Viewer >
Admin page.
iDefault TCP/IP information
- IP: 192.168.xxx.xxx
- Subnet Mask: 255.255.0.0
- Gateway: 192.168.0.1
- DNS : 168.126.63.1
iDefault ID / PW : root / pass
iCovert the last two sets of hexadecimal
numbers to decimal numbers.
MAC address = 00-13-23-01-14-B1
IP address =192.168.20.177
Wavestore Vision Thermal Mini Bullet IP Camera Quick Guide
Visit: wavestore.com
Specications may change without notice.
GLOBAL HQ (EMEA)
Wavestore Global Ltd.
Tel: +44 (0) 1895 527 127
USA/CANADA
Wavestore Americas Inc.
Toll-free: 855-526-8887
MIDDLE EAST
Wavestore Middle East
Tel: +971 (4)881 2903
5. IP Installer
4. Cabling
1Power Connection
Please, check the voltage and current
capacity of rated power carefully.
2Network Connection
Connect the crossover cable into the
RJ-45.
3BNC Connection
Used to connect video output device
such as monitor using the BNC coaxial
cable.
4Audio In
Connect the ‘Audio In’ cable of the
camera to the device like microphone.
5Audio Out
Connect the ‘Audio Out’ cable of the
camera to device like speaker.
Audio Out supports only RTSP Back
channel function. It plans to make it
available on the web later.
6Alarm In
Cable of the sensor/alarm input device
should connect to Yellow and Sky
Green line of the Alam cable.
7Alarm Out
It connects to the alarm lights, siren or
lamps and the sensor types are normal
open and normal close.
Cable of the alarm output device
should connect to DO1(N.O.) and DO1
COM of the cable slot.
1Power
2Network
3BNC
4Audio In
5Audio Out
7Alarm In
6Alarm In
Rate Power Power
Consumption PoE
DC 12V 11.9W IEEE 802.3af class3
AUDIO IN : PINK
AUDIO GND : PINK + DOT
AUDIO OUT : SKYBLUE
DI : SKY GREEN
DI COM : YELLOW
DO1 (N.O) : GREEN
DO1 COM : YELLOW + DOT
Preparing to Mount the Camera
1. The mounting surface must bear five times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line cover to be
damaged. This may cause a breakdown or fire.
3. CAUTION: These servicing instructions are for use by qualified service personnel
only. To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.
4. This product is intended to be supplied by a UL Listed Power Supply Unit marked
“Class 2” or “LPS” or “PS2” and rated 12 Vdc, 1A min or PoE (802.3af), 0.32A.
5. The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE
802.3af shall be a UL Listed device with the output evaluated as a Limited Power
Source as defined in UL60950-1 or PS2 as defined in UL62368-1.
6. Unit is intended for installation in a Network Environment 0 as defined in IEC TR
62102. As such, associated Ethernet wiring shall be limited to inside the building.
7. Using the mounting template sheet or the camera itself, mark and drill the necessary
holes in the wall or ceiling.
Disposal of Old Appliance
1. The symbol marked in the product, will follow and covered by the
Europe Directive 2002/95/EC.
2. All electornic disposal of waste is differenct by the government or
locally, so so it need to check.
3. The correct disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance,
please contact your city office, waste disposal service or the shop
where you purchased the product.
How to connect to the network
through the water proof cable
Insert the Lan cable into the rubber
first as (a) below. Put the Lan cable
into (b), then (c) will be assembled to
(b) tightly. As a final step, (d) need to
be assembled to (c) without making
any space.
1. Using a PoE-Enabled Switch
The Camera is PoE-compliant, allowing
transmission of power and data via a single
Ethernet cable.
PoE eliminates the need for the different
cables used to power, record, or control
the camera.
Follow the illustration below to connect
the camera to a PoE-enabled switch using
an Ethernet cable.
2. Using a Non-PoE Switch
If a PoE-enabled switch is not used, use a
power adaptor for power transmission and
non-PoE switch for data transmission.
Follow the illustrations below to connect
the camera without a PoE-enabled Switch.
Two Options
Use a PoE-enabled swtich to connect data and power through a single cable and begin
viewing and recording images instantly. A non-PoE switch will require an adaptor for power
transmission.
Ethernet Cable Ethernet Cable
Power
b
ac
d
2
4
3
5
7
8
9
6
10
12
11
1. Run IP Installer
1Run the IP installer.
2Click on Network Adaptor selection
Menu (NIC) after run this program.
3Select a network which a camera is
connected then click on a ‘Search’
button. (Takes about 5 sec.)
4Select a camera to set.
5The information of the selected
camera will be shown at Device Info.
6Select the network type.
iThe default network type of the
camera is STATIC.
iWhen set to DHCP, if you have a DHCP
server, it will automatically set the
Camera IP.
iWhen set to DHCP, if you do not have
a DHCP server, Camera IP is set to
192.168.xxx.xxx after one minute.
7Convert the device's MAC address to
the IP address.
The MAC Address of the device is
attached on the Product label.
Input IP setting information when the
network type is set to STATIC.
8Change the port as necessary when
the network type is set to STATIC.
9Input ID and PW of the camera for
authentication.
Make sure to change the ID and PW for
security reason.
Go to “Web viewer>Setup>System>
Users Management” for ID and PW
change.
The ID and PW will be set to default value
when ‘factory reset’ the camera.
10 Make sure to click on ‘Save’ button to
save changed values.
An “Apply” message will be popped-up
when the settings are applied normally,
or an error message will be popped-up
when failed.
11 To reboot or reset (except network
setting) the camera.
Select a camera (multiple camera can be
selected) > Input ID and PW > Click on
Reboot or Factory Reset button.
12 Able to delete an Active-X which is
installed when accessing to Web
Viewer.
You don’t need the function because this
camera use the VLC plugin instead of the
Active-X.
iA ‘Port Forwarding’ has to be set for
external access to the camera.
iRefer to the manual of the network hub
for ‘Port Forwarding’ settings.
iAn additional change of HTTPS, RTSP
port can be done at Web Viewer >
Admin page.
iDefault TCP/IP information
- IP: 192.168.xxx.xxx
- Subnet Mask: 255.255.0.0
- Gateway: 192.168.0.1
- DNS : 168.126.63.1
iDefault ID / PW : root / pass
iCovert the last two sets of hexadecimal
numbers to decimal numbers.
MAC address = 00-13-23-01-14-B1
IP address =192.168.20.177
Wavestore Vision Thermal Mini Bullet IP Camera Quick Guide
Visit: wavestore.com
Specications may change without notice.
GLOBAL HQ (EMEA)
Wavestore Global Ltd.
Tel: +44 (0) 1895 527 127
USA/CANADA
Wavestore Americas Inc.
Toll-free: 855-526-8887
MIDDLE EAST
Wavestore Middle East
Tel: +971 (4)881 2903
Other manuals for WV-CT-4F
1
Table of contents
Other wavestore Security Camera manuals
wavestore
wavestore WV-CT-4F User manual
wavestore
wavestore WV-8D-27V13 User manual
wavestore
wavestore Vision WV-8D-27V13-AI User manual
wavestore
wavestore WV-12F-360M-AI User manual
wavestore
wavestore WV-2B-28V12 User manual
wavestore
wavestore Vision WV-5D-28F User manual
wavestore
wavestore WV-5D-27V13 User manual
wavestore
wavestore WV-8B-27V13-AI User manual
wavestore
wavestore Vision 4K User manual
wavestore
wavestore WV-10M2-27V13 User manual
