Weber genesis II LX E-340 GBS User manual

Unlock grilling happiness: Register your GENESIS II LX gas grill and receive special
content to make you the ultimate backyard hero.
Registration is easy and we only ask a few quick questions. In less than two minutes,
activate your unique WEBER ID, and unlock a lifetime of WEBER knowledge and
guidance. Stay inspired along the way.
LPG OWNER’S MANUAL
PHONE MOBILE EMAIL ONLINE
Keep this Owner’s Manual for future reference, thoroughly read through it, and if you have any questions please contact us today-
contact information can be found at the back of this manual.
E240 GBS • E340 GBS • E440 GBS • E640 GBS
S240 GBS • S340 GBS • S440 GBS • S640 GBS
74386
040118
enGB - English (United Kingdom)
m DANGER
If you smell gas:
•Shut o gas to the appliance
(barbecue).
•Extinguish any open flame.
•Open lid.
•If odour continues, keep
away from the appliance
(barbecue) and immediately
call your gas supplier or the
emergency fire services.
m WARNING
•Do not store or use gasoline
or other flammable liquids
or vapours in the vicinity of
this (barbecue) or any other
appliance.
•An LPG cylinder not
connected for use shall not
be stored in the vicinity of
this (barbecue) or any other
appliance.
USE OUTDOORS ONLY.
READ THE INSTRUCTIONS BEFORE USING
THE APPLIANCE (BARBECUE).
Important
SafetyInformation
DANGER, WARNING, and CAUTION
statements are used throughout this
Owner's Manual to emphasise critical and
important information. Read and follow
these statements to help ensure safety and
prevent property damage. Thestatements
are defined below.
m DANGER: Indicates a hazardous
situation which, if not avoided,
will result in death or seriousinjury.
m WARNING: Indicates a hazardous
situation which, if not avoided,
could result in death or seriousinjury.
m CAUTION: Indicates a hazardous
situation which, if not avoided,
could result in minor or moderateinjury.
NOTICE TO INSTALLER: These instructions
must be left with the consumer.
NOTICE TO CONSUMER: Retain these
instructions for future reference.
845CR-0059
0845

3
Welcome to WEBER
ALWAYS
HAVE THE
LATEST AND
GREATEST
The most recent version of this
Owner’s Manual can be
found online.
The grills illustrated in this Owner’s Manual may vary
slightly from the model purchased.
Installation and Assembly
m DANGER: This barbecue is not intended to be
installed in or on recreational vehicles or boats.
m WARNING: Do not use this barbecue unless all
parts are in place and the barbecue was properly
assembled according to the assembly instructions.
m WARNING: Do not build this model of barbecue in any
built-in or slide-in construction.
m WARNING: Do not modify the appliance. LP gas is
not natural gas. The conversion or attempted use of
natural gas in an LP gas unit or LP gas in a natural
gas unit is unsafe and will void your warranty.
• Any parts sealed by the manufacturer must not be
altered by the user.
Operation
m DANGER: Only use the barbecue outdoors in a well-
ventilated area. Do not use in a garage, building,
breezeway, tent, any other enclosed area, or beneath
an overhead combustible structure.
m DANGER: Do not use the barbecue in any vehicle
or in any storage or cargo area of any vehicle.
This includes, but is not limited to, cars, trucks,
station wagons, mini-vans, sport utility vehicles,
recreational vehicles, andboats.
m DANGER: When in use, combustible materials should
not be within 61 cm (24 inches) of the back or sides of
the barbecue.
m DANGER: Keep the cooking area clear of flammable
vapours and liquids such as petrol, alcohol, etc., and
combustible materials.
m DANGER: This appliance must be kept away from
flammable materials during use.
m DANGER: Do not put a barbecue cover or anything
flammable on, or in the storage area under the
barbecue while it is in operation or is hot.
m DANGER: Should a grease fire occur, turn o all
burners and leave lid closed until fire is out.
m WARNING: Accessible parts may be very hot.
Keepyoung children away.
m WARNING: The use of alcohol, prescription drugs,
non-prescription drugs, or illegal drugs may impair
the consumer’s ability to properly and safely
assemble, move, store, or operate thebarbecue.
m WARNING: Never leave the barbecue unattended
during pre-heating or use. Exercise caution when
using this barbecue. The entire cookbox gets hot
when in use.
m WARNING: Use heat-resistant barbecue mitts or
gloves (conforming to EN 407, Contact Heat rating
level 2 or greater) when operating barbecue.
m WARNING: Do not move the appliance duringuse.
m WARNING: Keep any electrical supply cord and the
fuel supply hose away from any heated surfaces.
m CAUTION: This product has been safety-tested and
is only certified for use in a specific country. Refer to
country designation located on outside of box.
• Do not use charcoal, briquettes or lava rock in the
barbecue.
Storage and/or Nonuse
m WARNING: Turn o the gas supply at the gas cylinder
after use.
m WARNING: LPG cylinders must be stored outdoors
out of the reach of children and must not be stored
in a building, garage or any other enclosed space.
m WARNING: After a period of storage and/or nonuse,
the barbecue should be checked for gas leaks and
burner obstructions before use.
• Storage of the barbecue indoors is permissible only if
the LPG cylinder is disconnected and removed from
thebarbecue.
TABLE OF CONTENTS
2 Welcome to WEBER
Important SafetyInformation
4 Product Features
The GS4 GrillingSystem
GENESIS II LX Features
6 Tips and Hints
The Flame - Direct or Indirect
Grilling Do's and Don'ts
8 The WEBER Promise
Warranty
9 Getting Started
Important Information about LPGas
& Gas Connections
LPG Cylinder Installation
& LeakChecking
GENESIS II LX Burner Valve
OrificeSizes & Consumption Data
13 Operation
The Very First Time You Grill
Every Time You Grill
Igniting the Main Burners
Igniting the Side Burner
Grilling at Night
16 Product Care
Cleaning and Maintenance
18 Troubleshooting
22 Grilling Guide
23 Replacement Parts

4
Product Features
THE GS4 GRILLING SYSTEM
1 INFINITY Ignition
The INFINITY Ignition is ensured to ignite every
time. Backed by a generous warranty, rest
assured that you’ll be up-and-grilling the first
time, every time.
2 High Performance Burners
The unique, tapered shape delivers a consistent
gas flow from front to back. This provides
ultimate heat distribution, ensuring that food
grills evenly and consistently anywhere on the
cooking grate.
3 FLAVORIZER BARS
The classic WEBER FLAVORIZER BARS are
angled just right to catch drippings that smoke
and sizzle, adding that irresistible smoky flavor
that we all know and love to your food. Any
drippings not vaporised follow the slope and are
funneled away from the burners, down into the
grease management system.
4 Grease Management System
The grease management system helps with
the removal of grease while reducing the risk
of flare-ups. Drippings that are not vaporised
by the FLAVORIZER BARS are funneled away
from the burners into the disposable drip tray,
located within the catch pan under the cookbox.
Simply remove the catch pan and replace the
drip tray as needed.
The GS4 High Performance Grilling System sets a new standard in the world of backyard cuisine, and lands the GENESISII
and GENESIS II LX series of gas grills in a class of their own. Thisinnovative grilling system is based on over 30 years of
grilling experience, culinary expertise, and most importantly, avidly considering the wants and needs of the people who
matter most – thegrilling community.
Each component of GS4 was uniquely designed for ease-of-use and to provide an unequaled satisfaction to your backyard
grilling experience. Promising burners that are ensured to ignite every time, smoke infused food that grills evenly and
consistently regardless of where it’s placed on the cooking grate, and hassle free cleanup; you are able to focus on what it’s
is all about – bringing people together around the grill.
The GS4 grilling system is composed of four key components: The INFINITY Ignition, HighPerformance Burners, FLAVORIZER
BARS, and Grease Management System. These components ensure that every aspect of your grilling experience is easy and
reliable; from the moment the burners are lit to the general maintenance of your grill. Andtogether, create the strongest
grilling engine within every GENESIS II and GENESIS II LX grill.
12
3
4

5
Product Features
GENESIS II LX FEATURES
A Side Tables with Integrated Tool Hooks
Use the side tables to keep platters, seasonings, and
tools within arm’s reach. Hang your essential grilling
tools on the hooks for easy access and organisation
of your backyard workspace. The left side table folds
down in models equipped with two and three burners.
B HIGH+ Setting
All burners can be turned up to the highest setting for
an added boost of heat anywhere on the cooking grate.
The HIGH+ setting provides a quicker preheat and
higher grilling temperatures.
C Grill Light
The powerful LED illuminates the entire cooking area
of the grill so that you see the true colour of your food.
To save energy, the light will automatically turn o
when the lid is closed.
D GOURMET BBQ SYSTEM Cooking Grate
Remove the circular grate insert and transform your
grill into a griddle, poultry roaster, pizza stone or any
of the other many GOURMET BBQ SYSTEM inserts to
choose from.
E TUCKAWAY Warming Rack
The TUCK-AWAY warming rack keeps food warm or
toasts burger buns, as the main meal cooks below.
The unique TUCK-AWAY feature allows you to fold it
down when not in use, providing optimal grilling space
and convenient in-the-grill storage. The warming rack
can also be used as a tiered base for ELEVATIONS
accessories.
F iGRILL3 Ready
The newest grilling essential- the iGRILL 3 digital
Bluetooth thermometer monitors your food from
beginning to end, displaying the real-time temperature
on your mobile device. Once you’ve downloaded the
WEBER iGRILL app, connect the iGRILL to Bluetooth,
and run up to four thermometer probes from your grill
to the food. (Sold separately.)
G Side Burner
Use the side burner to simmer your specially crafted
BBQ sauce or boil potatoes while the main course
grills under the lid.
H Lighted Control Knobs
With a push of a button, the control knobs light up to
oer optimal control while night-time grilling. Whether
throwing a dinner party, or a daytime BBQ, you’ll never
have to sacrifice convenience or usability due to the
time of day.
I Easy Access Gas Cylinder Storage
Mounting the gas cylinder to the outside of the grill
makes the cylinder easy to access and remove; while
also increasing storage space within the cabinet.
J Grill Cabinet
The grill cabinet provides extra storage space for all
of your essential grilling tools. Everything you need at
your fingertips, when you need it.
A
B
C
D
E
FG
H
I
J

6
Tips and Hints
The Flame-
Direct or Indirect
INDIRECT HEAT
SETUP
Use the indirect method for larger cuts of meat that require 20
minutes or more of barbecuing time, or for foods so delicate that
direct exposure to the heat would dry them out or scorch them,
such as: roasts, bone-in poultry pieces, whole fish, delicate fish
fillets, whole chickens, turkeys, and ribs. Indirect heat can also
be used for finishing thicker foods or bone-in cuts that have been
seared or browned first over direct heat.
With indirect heat, the heat is on both sides of the barbecue, or o
to one side of the barbecue. The food sits over the unlit part on the
cooking grate.
INDIRECT HEAT
SETUP
DIRECT HEAT
SETUP
Use the direct method for small, tender pieces of food that take
less than 20 minutes to cook, suchas: hamburgers, steaks, chops,
kebab sticks, boneless chicken pieces, fish fillets, shellfish, and
slicedvegetables.
With direct heat, the fire is right below the food. It sears the
surfaces of the food, developing flavours, texture, and delicious
caramelisation while cooking the food all the way to thecentre.
DIRECT HEAT
SETUP
OFF
LOW
MEDIUM
IGNITE
HIGH+
HIGH
HIGH MEDIUM
OFF

7
Preheat each and every time.
If the cooking grates aren’t hot enough, food will
stick, and you will likely never have a chance of
searing properly or developing those handsome
barbecue marks. Even if a recipe calls for medium
or low heat, always preheat the barbecue on the
highest setting first. Open the lid, turn up the heat,
close the lid, and then let the cooking grate heat up
for about ten minutes or until the lid thermometer
reads 260°C (500°F) .
Don't barbecue on dirty grates.
Tossing food onto the cooking grates before they
have been cleaned is never a good idea. Leftover
“stu” on the grates acts like glue, binding it to
the grates and your new food. To avoid tasting last
night’s dinner on today’s lunch, make sure that you
are barbecuing on a clean cooking grate. Once the
grates are preheated, use a stainless steel bristle
barbecue brush to make a clean, smooth surface.
Be present in the process.
Before firing up your barbecue, make sure that
everything you need is within arm’s reach. Don’t
forget your essential barbecuing tools, already
oiled and seasoned food, glazes or sauces, and
clean cooking platters for cooked food. Having to
run back to your kitchen not only means missing
out on the fun, but could also result in burning
your food. French chefs call this "mise en place"
(meaning, “put in place”). We call it "being present".
Create a little elbow room.
Packing too much food onto the cooking grates
restricts your flexibility. Leave at least one-quarter
of the cooking grates clear, with plenty of space
between each food item, in order to get your tongs in
there and easily move the food around. Sometimes
barbecuing involves split-second decisions and
the ability to jockey food from one area to another.
Sogive yourself enough room to operate.
Try not to peek.
The lid on your barbecue is for more than just keeping
the rain out. Most importantly, it’s for preventing
too much air from getting in, and too much heat and
smoke from getting out. When the lid is closed, the
cooking grates are hotter, the barbecuing times are
faster, the smoky tastes are stronger, and the flare-
ups are fewer. So put a lid on it!
Only flip once.
What’s better than a juicy steak with a deep sear
and plenty of beautifully caramelised bits? The
key to accomplishing these results is to keep your
food in place. Sometimes we have the tendency
to flip our food before it reaches the desirable
level of colour and flavour. In nearly all cases, you
should turn food just once. If fiddling with it more
than that, you are probably also opening the lid too
much, which causes its own set of problems. So
step back and trust the barbecue.
Know when to tame the flame.
When barbecuing, sometimes the most important
thing to know is when to stop. The most reliable
way to test doneness of your food is to invest in an
instant-read thermometer. This slim little gem will
help you pinpoint that critical moment when your
food is at its best.
Don’t be afraid to experiment.
Back in the 1950s, barbecuing meant one thing:
meat (and only meat) charred over open flames.
Themodern day backyard chef doesn’t need a kitchen
in order to prepare a full course meal. Use your
barbecue to make char-barbecued appetisers, sides,
and even desserts. Register your barbecue to receive
special content that will inspire you along the way.
We’d love to join you on your barbecuing adventures.
BarbecuingDo’s
andDon’ts
Tips and Hints

8
The WEBER Promise
PROTECT
YOUR
INVESTMENT
Shield your grill from the
elements with a heavy-duty
premiumgrillcover.
Thank you for purchasing a WEBER product.
Weber-Stephen Products LLC, 1415 S. Roselle Road,
Palatine, Illinois 60067 and its International Business
Units (listed at the end of this manual) (“WEBER”) pride
ourselves on delivering a safe, durable, and reliable
product.
This is WEBER’s Voluntary Warranty provided to you
at no extra charge. It contains the information you
will need to have your WEBER product repaired or
replaced in the unlikely event of a failure or defect.
Pursuant to applicable laws, the Owner has several
rights in case the product is defective. Those
rights may include supplementary performance or
replacement, abatement of the purchasing price, and
compensation. In some countries in the European
Union, for example, this would be a two-year
statutory right starting on the date of the handover of
the product. These and other statutory rights remain
unaected by this Voluntary Warranty provision.
Infact, this Voluntary Warranty grants additional
rights to the Owner that are independent from
statutory provisions.
WEBER’s Voluntary Warranty
WEBER warrants, to the Purchaser of the WEBER
product (or in case of a gift or promotional situation,
the person for whom it was purchased as a gift or
promotional item) (“Owner”) that the WEBER product
is free from defects in material and workmanship
for ten (10) years from the date of purchase when
assembled and operated in accordance with the
accompanying Owner’s Manual. (Note: If you lose or
misplace your WEBER Owner’s Manual, a replacement
is available online at www.weber.com) The Warranty
is applicable in Europe, the Middle East and Africa
(EMEA). WEBER agrees to repair or replace the part
that is defective in material or workmanship subject
to the limitations, disclaimers, and exclusions listed
below. TO THE EXTENT ALLOWABLE BY APPLICABLE
LAW, THIS WARRANTY IS EXTENDED ONLY TO THE
ORGINAL PURCHASER AND IS NOT TRANSFERABLE
TO SUBSEQUENT OWNERS, EXCEPT IN THE CASE OF
GIFTS AND PROMOTIONAL ITEMS AS NOTED ABOVE.
WEBER stands by its products and is happy to
provide you with this Voluntary Warranty described
for material defects in the barbecue or its relevant
components, normal wear and tear excepted.
• ‘Normal wear and tear’ includes cosmetic and
other immaterial deterioration that may come with
ownership of your barbecue over time, such as surface
rust, dents / scratches, etc.
However, WEBER will honour this Voluntary Warranty
for the barbecue or its relevant components where
damage or dysfunction results from a material defect.
• ‘Material defect’ includes rust through or burn through
of certain parts, or other damage or failure inhibiting
your ability to safely / properly use your barbecue.
Owner’s Responsibilities Under this
Voluntary Warranty / Exclusion of
Warranty
To ensure trouble-free Warranty coverage, it is
important (but not required) that you register your
WEBER product online at www.weber.com. Please also
retain your original sales receipt and/or invoice as
Proof of Purchase is required for Warranty coverage.
WEBER will also require photographs of any alleged
defect, and the serial number of your barbecue, prior
to processing a Warranty claim. Registering your
WEBER product confirms your Warranty coverage and
provides a direct link between you and WEBER in case
we need to contact you.
The above Voluntary Warranty only applies if the
Owner takes reasonable care of the WEBER product
by following all assembly instructions, usage
instructions, and preventative maintenance as
outlined in the accompanying Owner’s Manual, unless
the Owner can prove that the material defect or failure
is independent of non-compliance with the above
mentioned obligations. If you live in a coastal area, or
have your product located near a pool, maintenance
includes regular washing and rinsing of the exterior
surfaces as outlined in the accompanying Owner’s
Manual.
This Voluntary Warranty lapses if there are damages,
deteriorations, discolourations, and/or rust for which
WEBER is not responsible caused by:
• Abuse, misuse, alteration, modification, misapplication,
vandalism, neglect, improper assembly or installation,
and failure to properly perform normal and routine
maintenance;
• Insects (such as spiders) and rodents (such as
squirrels), including but not limited to damage to gas
hoses;
• Exposure to salt air and/or chlorine sources such as
swimming pools and hot tubs/spas;
• Severe weather conditions such as hail, hurricanes,
earthquakes, tsunamis or surges, tornadoes or severe
storms.
• Acid rain and other environmental factors.
The use and/or installation of parts on your WEBER
product that are not genuine WEBER parts will void
this Voluntary Warranty, and any damages that result
hereby are not covered by this Voluntary Warranty.
Any conversion of a gas barbecue not authorised by
WEBER and performed by a WEBER authorized service
technician will void this Voluntary Warranty.
Warranty Processing
If you believe that you have a part which is covered by
this Voluntary Warranty, please contact your purchase
dealer. If needed, you may also contact WEBER
Customer Service using the contact information
on our website (www.weber.com). WEBER will,
upon investigation, repair or replace (at its option)
a defective part that is covered by this Voluntary
Warranty. In the event that repair or replacement are
not possible, WEBER may choose (at its option) to
replace the barbecue in question with a new barbecue
of equal or greater value. WEBER may ask you to
return parts for inspection, shipping charges to be
pre-paid by the Owner. The shipping charges will be
reimbursed to the Owner if the defect is covered by the
Warranty.
When you contact your purchase dealer, please have
the following information available:
• Proof of Purchase
• Photographs of the alleged defect
• Product serial number
Disclaimers
APART FROM THE WARRANTY AND DISCLAIMERS
AS DESCRIBED IN THIS VOLUNTARY WARRANTY
STATEMENT, THERE ARE EXPLICITLY NO FURTHER
WARRANTY OR VOLUNTARY DECLARATIONS OF
LIABILITY GIVEN HERE WHICH GO BEYOND THE
STATUTORY LIABILITY APPLYING TO WEBER. THE
PRESENT VOLUNTARY WARRANTY STATEMENT
ALSO DOES NOT LIMIT OR EXCLUDE SITUATIONS OR
CLAIMS WHERE WEBER HAS MANDATORY LIABILITY
AS PRESCRIBED BY STATUTE.
NO WARRANTIES SHALL APPLY AFTER THE
TEN (10) YEAR PERIOD OF THIS VOLUNTARY
WARRANTY. NO OTHER WARRANTIES GIVEN BY
ANY PERSON, INCLUDING A DEALER OR RETAILER,
WITH RESPECT TO ANY PRODUCT (SUCH AS ANY
“EXTENDED WARRANTIES”), SHALL BIND WEBER.
THE EXCLUSIVE REMEDY OF THIS VOLUNTARY
WARRANTY IS REPAIR OR REPLACEMENT OF THE
PART OR PRODUCT.
IN NO EVENT UNDER THIS VOLUNTARY WARRANTY
SHALL RECOVERY OF ANY KIND BE GREATER THAN
THE AMOUNT OF THE PURCHASE PRICE OF THE
WEBER PRODUCT SOLD.
PARTS AND ACCESSORIES REPLACED UNDER THIS
VOLUNTARY WARRANTY ARE WARRANTED ONLY FOR
THE REMAINING PERIOD OF THE ABOVE MENTIONED
ORIGINAL TEN (10) YEAR VOLUNTARY WARRANTY
PERIOD.
THIS LIMITATION DOES NOT APPLY IN CASES OF
INTENT AND GROSS NEGLIGENCE AND CASES OF
INJURY TO HUMAN LIFE OR HEALTH OR PERSONAL
INJURY WHETHER THE INJURY WAS THE FAULT
OF WEBER OR ITS LEGAL REPRESENTATIVES OR
AGENTS.
THIS VOLUNTARY WARRANTY APPLIES TO PRIVATE
USE ONLY AND DOES NOT APPLY TO WEBER
BARBECUES USED IN COMMERCIAL, COMMUNAL OR
MULTI-UNIT SETTINGS SUCH AS RESTAURANTS,
HOTELS, RESORTS, OR RENTAL PROPERTIES.
WEBER MAY FROM TIME TO TIME CHANGE THE
DESIGN OF ITS PRODUCTS. NOTHING CONTAINED IN
THIS VOLUNTARY WARRANTY SHALL BE CONSTRUED
AS OBLIGATING WEBER TO INCORPORATE
SUCH DESIGN CHANGES INTO PREVIOUSLY
MANUFACTURED PRODUCTS, NOR SHALL SUCH
CHANGES BE CONSTRUED AS AN ADMISSION THAT
PREVIOUS DESIGNS WERE DEFECTIVE.
The WEBER Promise (10 year EMEA voluntary warranty)
At WEBER, we pride ourselves on two things: making barbecues that last
and providing a lifetime of excellent customer service.

9
Getting Started
Important Information about
LPGas & GasConnections
What is LPG?
Liquefied petroleum gas, also called LPG or LP gas, is
the flammable, petroleum-based product used to fuel
your barbecue. It is a gas at moderate temperatures
and pressure when it is not contained. But at moderate
pressure inside a container, such as a cylinder, LPG is
a liquid. As pressure is released from the cylinder, the
liquid readily vaporises and becomes gas.
Safe Handling Tips for LPG Cylinders
• A dented or rusty LPG cylinder may be hazardous and
should be checked by your LP gas supplier. Donot use
a cylinder with a damaged valve.
• Although your LPG cylinder may appear to be empty,
gas may still be present, and the cylinder should be
transported and stored accordingly.
• The LPG cylinder must be installed, transported, and
stored in an upright, secure position. Cylinders should
not be dropped or handled roughly.
• Never store or transport the LPG cylinder where
temperatures can reach 50°C (125°F) (the cylinder will
become too hot to hold by hand).
LPG Cylinder Requirements
• Use cylinders with a minimum capacity of 3 kg and
amaximum capacity of 13 kg.
What is a Regulator?
Your gas barbecue is equipped with a pressure
regulator, which is a device to control and maintain
uniform gas pressure as gas is released from the
LPGcylinder.
Regulator and Hose Requirements
• In the United Kingdom, this barbecue must be fitted
with a regulator complying with BS 3016, having a
nominal output of 37 millibars.
• The length of the hose must not exceed 1.5 metres.
• Avoid kinking the hose.
• Replacement regulator and hose assemblies must be
as specified by Weber-Stephen Products LLC.
m IMPORTANT: We recommend that you replace
the gas hose assembly on your gas barbecue
every five years. Some countries may have
requirements that the gas hose be replaced
within less than five years, in which case that
country’s requirement would take precedence.
For replacement hose, regulator, and valve
assemblies, contact the Customer Service
Representative in your area using the contact
information on our web site.
Log on to weber.com.

10
Getting Started
LPG Cylinder Installation
&LeakChecking
Connect the Regulator to the Cylinder
1) Check that all burner control knobs are in the
o position. Check by pushing in and turning
knobs clockwise.
2) Identify your regulator type and connect the
regulator to the LPG cylinder by following the
appropriate connection instructions.
Note: Confirm that the LPG cylinder valve or regulator
lever are closed before connecting.
Connect by Turning Clockwise (A)
Screw regulator onto cylinder by turning fitting
clockwise (a). Position the regulator so that the vent
hole (b) faces down.
Connect by Turning Anti-Clockwise (B)
Screw regulator onto cylinder by turning fitting
anti-clockwise.
Connect by Turning Lever and
Snapping into Position (C)
Turn regulator lever (a) clockwise to the o position.
Push regulator down on cylinder valve until
regulator snaps into position (b).
Connect by Sliding Collar (D)
Make sure regulator lever is in the o position (a).
Slide the collar of the regulator up (b). Push the
regulator down onto the cylinder valve and maintain
pressure. Slide collar down to close (c). If regulator
does not lock, repeat procedure.
Note: The regulator illustrations shown in this manual
may not be similar to the regulator you are using for your
grill, due to dierent country or regional regulations.
Placement of the LPGCylinder
The size and shape of the cylinder determine if the
cylinder is placed on the cylinder hanger or placed on
the ground.
1) Identify your LPG cylinder type and follow the
appropriate placement instructions.
Hanger Placement (E)
Turn the cylinder so the valve opening faces the
front of the grill. Lift and place the cylinder on
the hanger. Adjust the belt so that it is tight to the
cylinder.
Ground Placement (F)
Place the cylinder on the ground outside the base
cabinet on the right side of the grill. Turn the
cylinder so the valve opening faces the front of
thegrill.

11
Getting Started
What is a Leak Check?
Once the LPG cylinder is properly installed, it is
necessary to perform a leak check. A leak check is a
reliable way to verify that gas is not escaping after you
connect the cylinder. The fitting where the regulator
connects to the cylinder should be tested each time a
cylinder is refilled andreinstalled.
Checking for Gas Leaks
1) Wet fittings at cylinder and regulator with a soap
and water solution, using a spray bottle, brush
or rag. You can make your own soap and water
solution by mixing 20% liquid soap with 80% water;
or, you can purchase leak check solution in the
plumbing section of any hardware store.
2) Identify your regulator type. Turn gas supply on
by turning cylinder valve anti-clockwise (G) or by
moving regulator lever to the on position(H).
3) If bubbles appear (I) at the regulator-to-cylinder
connection or the regulator hose-to-regulator
connection, there is a leak:
a) Turn gas supply o. DO NOT OPERATE
THE GRILL. Contact the Customer Service
Representative in your area using the contact
information on our website.
4) If bubbles do not appear, leak checking is complete:
a) Turn gas supply o and rinse connections
withwater.
NOTE: Since some leak test solutions, including soap and
water, may be slightly corrosive, all connections should
be rinsed with water after checking for leaks.
Additional Leak Check Precautions
The fuel system in your grill features other
connections and fittings. These factory-made
connections have been thoroughly checked for gas
leaks and the burners have been flame-tested.
WEBER recommends performing an additional
thorough leak check after assembly, as well as
annually. Instructions for this can be found online at
WEBER.com.
Disconnect the Regulator from
theCylinder
1) Confirm that the LPG cylinder valve or regulator
lever are fully closed.
2) Disconnect the regulator.
m DANGER: Do not use a flame to check for gas
leaks. Besure there are no sparks or open
flames in the area while you check for leaks.
m DANGER: Leaking gas may cause a fire or
explosion.
m DANGER: Do not operate the barbecue if there
is a gas leak present.
m DANGER: If you see, smell, or hear the hiss of
gas escaping from the LPG cylinder:
1. Move away from LPG cylinder.
2. Do not attempt to correct the problem
yourself.
3. Call the emergency fire services.
m DANGER: Always close the cylinder valve
before disconnecting the regulator. Do not
attempt to disconnect the gas regulator
and hose assembly or any gas fitting while
this barbecue is in operation.
m DANGER: Do not store a spare LPG cylinder
under or near this barbecue. Never fill the
cylinder beyond 80% full. Failure to follow
these statements exactly may result in a
fire causing death or serious injury.

12
Getting Started
GENESIS II LX Burner Valve Orifice Sizes & Consumption Data
BURNER VALVE ORIFICE SIZES
Country Gas Category 2 Burner Models 3 Burner Models 4 Burner Models 6 Burner Models
China, Cyprus,
CzechRepublic, Denmark,
Estonia, Finland, HongKong,
Hungary, Iceland, India,
Israel, Japan, Korea,
Latvia, Lithuania, Malta,
Netherlands, Norway,
Romania, Russia, Singapore,
SlovakRepublic, Slovenia,
South Africa, Sweden,
Turkey
I3B/P (30 mbar or 2.8 kPa) Main Burners 1,06 mm
Side Burner 1,02 mm
Main Burners 1,06 mm
Side Burner 1,02 mm
Main Burners 1,03 mm
Side Burner 1,02 mm
Main Burners 0,98 mm
Side Burner 1,02 mm
Belgium, France,
Greece, Ireland, Italy,
Luxembourg, Portugal,
Spain, Switzerland,
UnitedKingdom
I3+ (28-30/37 mbar) Main Burners 0,98 mm
Side Burner 0,96 mm
Main Burners 1,02 mm
Side Burner 0,96 mm
Main Burners 0,96 mm
Side Burner 0,96 mm
Main Burners 0,92 mm
Side Burner 0,96 mm
Poland I3P (37 mbar) Main Burners 0,98 mm
Side Burner 0,96 mm
Main Burners 1,02 mm
Side Burner 0,96 mm
Main Burners 0,96 mm
Side Burner 0,96 mm
Main Burners 0,92 mm
Side Burner 0,96 mm
Austria, Germany I3B/P (50 mbar) Main Burners 0,93 mm
Side Burner 0,85 mm
Main Burners 0,94 mm
Side Burner 0,85 mm
Main Burners 0,86 mm
Side Burner 0,85 mm
Main Burners 0,84 mm
Side Burner 0,85 mm
CONSUMPTION DATA
2 Burner Models 3 Burner Models 4 Burner Models 6 Burner Models
12,0 kW Propane
13,8 kW Butane
858 g/h Propane
1004 g/h Butane
16,3 kW Propane
18,7 kW Butane
1165 g/h Propane
1361 g/h Butane
18,7 kW Propane
21,5 kW Butane
1337 g/h Propane
1565 g/h Butane
24,6 kW Propane
28,3 kW Butane
1758 g/h Propane
2059 g/h Butane

13
Operation
The Very First Time You Grill
Perform an Initial Burn-Off
Heat the grill on the highest setting, with the lid
closed, for at least 20 minutes prior to grilling for the
firsttime.
Every Time You Grill
Meal-to-Meal Maintenance
The Meal-To-Meal Maintenance plan includes the
following simple, yet important, steps that should
always be performed prior to grilling.
Check for Grease
Your grill was built with a grease management
system that funnels grease away from food and into a
disposable container. As you cook, grease is channeled
down the slide-out grease tray and into a disposable
drip tray that lines the catch pan. This system
should be cleaned each and every time you grill to
preventfires.
1) Confirm that the grill is o and cool.
2) Remove the slide-out grease tray by pulling the tray
out of the cabinet (A). Remove excess grease with a
plastic scraper.
3) Remove the catch pan (B). Check for excessive
amounts of grease in the disposable drip tray that
lines the catch pan. Discard disposable drip pan
when necessary and replace with a new one.
4) Reinstall all components.
Inspect the Hose
Routine inspection of the hose is necessary.
1) Confirm that the grill is o and cool.
2) Check hose for any signs of cracking, abrasions, or
cuts(C). If the hose is found to be damaged in any
way, do not use the grill.
Preheat the Grill
Preheating the grill is critical to successful grilling.
Preheating helps to prevent food from sticking to the
grate and gets the grate hot enough to sear properly.
Italso burns o residue of a previously cooked meal.
1) Open the grill lid.
2) Ignite your grill according to the ignition
instructions in this owner's manual.
3) Close lid.
4) Preheat the grill with all burners on the HIGH+
position for 10 to 15 minutes or until thermometer
registers 260°C (500°F)(D).
Clean the Cooking Grate
After preheating, any bits of food or debris left over
from previous use will be easier to remove. Cleaned
grates will also prevent your next meal from sticking.
1) Brush the grates with a stainless steel bristle grill
brush immediately after preheating (E).
m DANGER: Do not line the slide-out grease tray
or cookbox with aluminum foil.
m DANGER: Check the slide-out grease tray and
catch pan for grease build-up before each
use. Remove excess grease to avoid a grease
fire.
mWARNING: Use heat-resistant barbecue mitts
or gloves (conforming to EN 407, Contact
Heat rating level 2 or greater) when
operating barbecue.
m WARNING: Grill brushes should be checked for
loose bristles and excessive wear on a
regular basis. Replace brush if any loose
bristles are found on cooking grates or brush.
WEBER recommends purchasing a new
stainless steel bristle grill brush at the
beginning of every spring.
m WARNING: If the hose is found to be damaged
in any way, do not use the grill. Replace
using only WEBER authorised replacement
hose.
mWARNING: Keep ventilation openings around
tank clear and free of debris.

14
Operation
Igniting the Main Burners
Using the Electronic Ignition to
Ignite the Main Burners
Each control knob operates an individual burner, and
each burner ignites independently. Ignite the main
burners starting from left to right. All burners should
be lit for preheating, however, all burners do not have
to be lit while grilling.
1) Open the grill lid (A).
2) Check that all burner control knobs (including side
burner control knob) are in the o position. Check
by pushing in and turning knobs clockwise (B).
Note: It is important that all burner control knobs are
in the o position before turning on the LPG cylinder.
3) Turn gas supply on by turning cylinder valve
anti-clockwise or by moving regulator lever to the
onposition depending on your regulator/cylinder
connection.
4) Begin with the burner furthest to the left. Pushthe
burner control knob in and slowly turn it anti-
clockwise toward the ignite position until you
hear ticking(C). Once ticking starts, hold the knob
in that position for 1-2 seconds and then slowly
continue turning anti-clockwise. The burner should
ignite before the HIGH+ position.
5) Check that the burner is lit by looking through the
cooking grates and through the half-circle cutout in
the FLAVORIZER BAR.
6) Once burner is ignited, continue turning the knob
anti-clockwise until you reach the desired position.
7) If the burner does not ignite within 4 seconds,
turn burner control knob to the o position and
wait five minutes to allow the gas to clear before
attempting to light the burner again.
8) If the burner ignites, repeat steps 4 through 6 to
light the remaining main burners.
Should the burners fail to ignite using the electronic
ignition, refer to the TROUBLESHOOTING section.
Thereyou will find instructions on igniting the grill with
a match to help determine the exact problem.
To Extinguish Main Burners
1) Push each burner control knob in and then turn
clockwise all the way to the o position.
2) Turn gas supply o at the LPG cylinder.
m WARNING: Open lid during ignition.
m WARNING: Do not lean over open grill while
igniting or cooking.
m WARNING: If ignition does not occur within
four seconds of attempting to light the first
burner, turn the burner control knob to
the o position. Wait five minutes to allow
accumulated gas to dissipate, and then
repeat the lighting procedure.
Optimize
Grill Space
Using the TUCKAWAY Warming Rack
Use the warming rack up to keep food warm or
fold it down when not in use. The warming rack
can also be used when folded down as a tiered
base for ELEVATIONS accessories.
To fold the warming rack down, lift rack slightly
and rotate downward. Use heat-resistant mitts
or gloves (conforming to EN 407, Contact Heat
rating level 2 or greater) when adjusting rack.

15
Igniting the Side Burner
Using the Electronic Ignition to
Ignite the Side Burner
If one or more of the main burners on your grill are
already lit and you would like to ignite the side burner,
skip to step 3. If none of the main burners are lit and
you are only using the side burner, start with step 1.
1) Check that the side burner control knob is in the
o position. Check by pushing in and turning
knob clockwise (A). Also check that all main burner
control knobs are in the o position.
Note: It is important that all burner control knobs are
in the o position before turning on the LPG cylinder.
2) Turn gas supply on by turning cylinder valve
anti-clockwise or by moving regulator lever to the
onposition depending on your regulator/cylinder
connection.
3) Open the side burner lid (B).
4) Pushthe side burner control knob in and slowly
turn it anti-clockwise toward the ignite position
until you hear ticking(C). Once ticking starts, hold
the knob in that position for 1-2 seconds and then
slowly continue turning anti-clockwise. The burner
should ignite at the high position.
5) Check that the side burner is lit. The side burner
flame may be dicult to see on a bright sunny day.
6) Once side burner is ignited, continue turning the
knob anti-clockwise until you reach the desired
position.
7) If the side burner does not ignite within 4 seconds,
turn side burner control knob to the o position
and wait five minutes to allow the gas to clear
before attempting to light the burner again.
Should the side burner fail to ignite using the
electronic ignition, refer to the TROUBLESHOOTING
section. Thereyou will find instructions on igniting the
side burner with a match to help determine the exact
problem.
To Extinguish Side Burner
1) Push side burner control knob in and then turn
clockwise all the way to the o position.
2) Turn gas supply o at the LPG cylinder.
m WARNING: Open side burner lid during
ignition.
m WARNING: Do not lean over side burner while
igniting or cooking.
m WARNING: If ignition does not occur within
four seconds of attempting to light the side
burner, turn the burner control knob to
the o position. Wait five minutes to allow
accumulated gas to dissipate, and then
repeat the lighting procedure.
Using the Lighted Control Knobs
The burner control knobs light up with the push
of a button. To turn on or o, simply push the
power button located on the right side of the
control panel.
Grilling
atNight
Using the Grill Light
To activate the grill light press the awake button.
The grill light has a tilt sensor that will turn on
the light if the grill lid is opened and turn o the
light when the grill lid is closed. If the lid is left
open or closed for more than 30 minutes, the
grill light will automatically deactivate. To turn
the light back on, press the awakebutton.
NOTE: The light does not turn o by pressing the
awakebutton.
Operation

16
Product Care
Cleaning and Maintenance
Cleaning the Inside of the Grill
Over time, the performance of your grill can
diminish if it has not been maintained properly.
Low temperatures, uneven heat, and food sticking
to cooking grates are all signs that cleaning and
maintenance are overdue. When your grill is o and
cool, start by cleaning the inside, from the top down.
A thorough cleaning is recommended at least twice a
year. Consistent use may require quarterly cleanings.
Cleaning the Lid
From time to time you may notice “paint-like” flakes
on the inside of the lid. During use, grease and smoke
vapours slowly change into carbon and deposit on the
inside of your lid. These deposits will eventually peel,
and look very similar to paint. These deposits are non-
toxic, but the flakes could fall onto your food if you do
not clean the lid regularly.
1) Brush the carbonised grease from the inside of the
lid with a stainless steel bristle grill brush (A). To
minimise further build-up, the inside of the lid can
be wiped with a paper towel after grilling while the
grill is still warm (nothot).
Cleaning the Cooking Grates
If you have been cleaning your cooking grates as
recommended, the debris on your grates should be
minimal.
1) With grates installed, brush the debris o your
cooking grate with a stainless steel bristle grill
brush(B).
2) Take the grates out and set aside.
Cleaning the FLAVORIZERBARS
FLAVORIZER BARS catch drippings that smoke and
sizzle, adding flavour to your food. Any drippings
that are not vaporised by the FLAVORIZER BARS are
funneled away from the burners. This helps prevent
flare-ups inside of your grill, and protects the burners
from getting clogged.
1) Scrape the FLAVORIZER BARS with a plastic
scraper(C).
2) If necessary, brush the FLAVORIZER BARS with a
stainless steel bristle grill brush.
3) Remove FLAVORIZER BARS and set aside.
Cleaning the Burners
Two areas on the burners that are key to optimum
performance are the ports (small raised openings
running along the length of the burners) and the
spider/insect screens on the ends of the burner.
Keeping these areas clean is essential for safe
operation.
Cleaning the Burner Ports
1) Use a clean stainless steel bristle grill brush to
clean the outside of the burners by brushing across
the top of the burner ports (D).
2) When cleaning the burners, avoid damaging the
ignition electrode by carefully brushing around
it(E).
Cleaning the Spider Screens
1) Locate the ends of the burners on the underside of
the control panel where they meet the valves.
2) Clean the spider/insect screens on each of the
burners using a soft bristle brush (F).
WARNING: Turn your barbecue o and wait for
it to cool before thoroughly cleaning.
WARNING: Over time, the development of
rough surfaces can form on the FLAVORIZER
BARS. Wearing gloves is recommended when
handling. Do not clean FLAVORIZER BARS or
cooking grates in a sink, dishwasher, or self-
cleaning oven.
WARNING: When cleaning the burners, never
use a brush that has already been used to
clean the cooking grates. Never put sharp
objects into the burner port holes.
CAUTION: Do not place any barbecue
components onto the side tables as they may
scratch the paint or stainless steel surfaces.
CAUTION: Do not use any of the following
to clean your barbecue: abrasive stainless
steel polishes or paints, cleaners that contain
acid, mineral spirits or xylene, oven cleaner,
abrasive cleansers (kitchen cleansers), or
abrasive cleaning pads.

17
Product Care
Cleaning the Heat Deflectors
Located under the burners, the heat deflectors
distribute heat evenly throughout the cookbox while
cooking. Keeping heat deflectors clean will enhance
the cooking performance of your grill.
1) Scrape the heat deflectors with a plastic
scraper(G).
2) If necessary, brush the heat deflectors with a
stainless steel bristle grill brush.
3) Remove heat deflectors and set aside.
Cleaning the Cookbox
Look inside the cookbox for any grease accumulation
or leftover food particles. Excessive accumulation can
cause a fire.
1) Use a plastic scraper to scrape debris o the
sides and bottom of the grill into the opening in
the bottom of the cookbox(H). This opening leads
debris into the slide-out grease tray.
Cleaning the Grease ManagementSystem
The grease management system consists of an
angled slide-out grease tray and a catch pan. These
components were designed to be easily removed,
cleaned, and replaced; an essential step every time
you prepare to grill. Instructions on inspecting the
grease management system can be found in MEAL-TO-
MEAL MAINTENANCE.
Cleaning the Outside of theGrill
The outside of your grill may include stainless steel,
porcelain-enameled, and plastic surfaces. WEBER
recommends the following methods based on the
surfacetype.
Cleaning Stainless Steel Surfaces
Clean stainless steel using a non-toxic, non-abrasive
stainless steel cleaner or polish designed for use on
outdoor products and grills. Use a microfiber cloth to
clean in the direction of the grain of the stainless steel.
Donot use paper towels.
Note: Do not risk scratching your stainless steel with
abrasive pastes. Pastes do not clean or polish. They
will change the colour of the metal by removing the top
chromium oxide film coating.
Cleaning Painted, Porcelain-Enameled
Surfaces and PlasticComponents
Clean painted, porcelain-enameled and plastic
components with warm soapy water, and paper towels
or cloth. After wiping down the surfaces, rinse and dry
thoroughly.
Cleaning the Outside of Grills that are in
Unique Environments
If your grill is subject to a particularly harsh
environment, you will want to clean the outside more
often. Acid rain, pool chemicals, and salt water can
cause surface rusting to appear. Wipe down the
outside of your grill with warm soapy water. Follow
up with a rinse and thorough drying. Additionally, you
may want to apply a stainless steel cleaner weekly to
prevent surface rust.
Cleaning the Grill Light
Wipe the grill light clean with a damp cloth only. The
light is weather resistant to rain and snow, but not
waterproof. Do not submerge in water.

18
Troubleshooting
m WARNING: Do not attempt to make any
repair to gas carrying, gas burning, ignition
components or structural components
without contacting Weber-Stephen Products
LLC, Customer Service Department.
m WARNING: Failure to use genuine Weber-
Stephen parts for any repair or
replacement will void all warranty
protection.
m CAUTION: The burner tube openings must
be positioned properly over the valve orifices.
Lighting Your Grill with a Match
Using a Match to Determine if there is
Gas Flow to the Main Burners
1) Open the grill lid.
2) Check that all burner control knobs (including side
burner control knob) are in the o position. Check
by pushing in and turning knobs clockwise.
Note: It is important that all burner control knobs
are in the o position before turning on the LPG
cylinder.
3) Turn gas supply on by turning cylinder valve
anti-clockwise or by moving regulator lever to the
onposition depending on your regulator/cylinder
connection.
4) Begin with the burner furthest to the left. Put
match in the matchstick holder and strike match.
(Matchstick holder is located under right side
table.) Insert lit match down through the cooking
grates, past the FLAVORIZER BARS and next to the
burner(A).
5) Pushthe burner control knob in and slowly turn it
anti-clockwise toward the ignite position until
you hear ticking. Once ticking starts, hold the knob
in that position for 1-2 seconds and then slowly
continue turning anti-clockwise. The burner should
ignite before the HIGH+ position.
6) Check that the burner is lit by looking through the
cooking grates and through the half-circle cutout in
the FLAVORIZER BAR.
7) If the burner does not ignite within 4 seconds,
turn burner control knob to the o position and
wait five minutes to allow the gas to clear before
attempting to light the burner again. If repeated
attempts fail, follow the gas flow troubleshooting
instructions on the next page.
8) If the burner ignites, the problem lies in the ignition
system. Follow the instructions for “Checking the
Components of the Electronic Ignition System”.
9) Replace the matchstick holder by hanging
underneath right side table (B).
Using a Match to Determine if there is
Gas Flow to the Side Burner
1) Open the side burner lid.
2) Check that the side burner control knob is in the
o position. Check by pushing in and turning knob
clockwise. Also check that all main burner control
knobs are in the o position.
Note: It is important that all burner control knobs
are in the o position before turning on the LPG
cylinder.
3) Turn gas supply on by turning cylinder valve
anti-clockwise or by moving regulator lever to the
onposition depending on your regulator/cylinder
connection.
4) Put match in the matchstick holder and strike
match. (Matchstick holder is located under right
side table.) Hold lit match by the side burner(C).
5) Pushthe side burner control knob in and slowly
turn it anti-clockwise toward the ignite position
until you hear ticking. Once ticking starts, hold
the knob in that position for 1-2 seconds and then
slowly continue turning anti-clockwise. Theburner
should ignite at the high position.
6) Check that the side burner is lit. The side burner
flame may be dicult to see on a bright sunny day.
7) If the side burner does not ignite within 4 seconds,
turn side burner control knob to the o position
and wait five minutes to allow the gas to clear
before attempting to light the burner again.
If repeated attempts fail, follow the gas flow
troubleshooting instructions on the next page.
8) If the burner ignites, follow the instructions for
“Checking the Components of the Electronic Ignition
System”.
MAIN BURNERS or SIDE BURNER WILL NOT IGNITE
SYMPTOM
• Main burners or side burner do(es) not ignite when following the electronic ignition instructions in the “Operation” section of
this owner's manual.
CAUSE SOLUTION
There is a problem with gas flow. If any burner does not ignite, the first step is to determine if there is gas flowing to the burner(s). Tocheck
this, follow the instructions below for “Lighting Your Grill with a Match.”
If match lighting IS NOT successful, follow the “GAS FLOW” troubleshooting suggestions on the next page.
There is a problem with the electronic ignition system. If any burner does not ignite, the first step is to determine if there is gas flowing to the burner(s). Tocheck this,
follow the instructions below for “Lighting Your Grill with a Match.”
If match lighting IS successful, follow the instructions for “Checking the Components of the Electronic
IgnitionSystem.”

19
Troubleshooting
Proper Burner Flame Pattern
The burners in your grill were factory set for the
correct air and gas mixture. When the burners
are performing correctly, you will see a specific
flame pattern. The tips may occasionally flicker
yellow (A), with a descending light blue (B) to
dark blue flame (C).
Spider Screens
The combustion air openings of the burners(D)
are fitted with stainless steel screens to
prevent spiders and other insects from spinning
webs and building nests inside the burners.
Additionally, dust and debris can accumulate
on the outside of the spider/insect screen and
obstruct the oxygen flow to the burners.
Checking the Components of the Electronic Ignition System
When turning the control knob you should hear a
ticking sound. If you cannot hear the ticking sound,
check the batteries, then check the wires.
Checking the Batteries
There are three potential issues with the batteries that
supply the power to your ignition modules that need to
be checked:
1) Some batteries have a plastic protective wrap
around them. (Do not confuse this plastic with
the battery label.) Check that this plastic wrap is
removed.
2) Confirm that the batteries in both ignition modules
are installed correctly (E).
3) If the batteries are old, replace them with new
batteries.
Checking the Wires
1) Make sure the ignition wires are properly attached
to the ignition modules. The wire terminals are
colour coded to correspond with the terminals on
the ignition module. The number of wires will vary
per model.
A
B
C
GAS FLOW
SYMPTOM
• Barbecue does not reach desired temperature or heatsunevenly.
• One or more of the burners fail to ignite.
• Flame is low when burner is on high position.
• Flames do not run the whole length of the burner.
• Burner flame pattern is erratic.
CAUSE SOLUTION
Some countries have regulators with a “flow limiting
device” that has been activated. Thissafety feature
built into the regulator restricts the gas flow in the
event of a gas leak. You can inadvertently activate this
safety feature without having a gas leak. This typically
occurs when you turn on the gas at the LPG cylinder
and one or more of the control knobs are not in the
o position. It may also occur if you turn on the LPG
cylinder too quickly.
Reset the “flow limiting device” by closing the LPG
cylinder valve and turning all the burner control
knobs to the o position. Wait five minutes to
allow accumulated gas to dissipate, then ignite the
barbecue again following the instructions in the
“Operation” section.
The LPG cylinder is low or empty. Refill LPG cylinder.
Fuel hose is bent or kinked. Straighten fuel hose.
Burner ports are dirty.
Clean burner ports. Refer to “Cleaning the BurnerPorts.”
SYMPTOM
• Gas is smelled in conjunction with burner flames that appear yellow andlazy.
CAUSE SOLUTION
Spider screens on the burners are obstructed. Clean spider screens. Refer to “Cleaning the Spider
Screens” in the Product Care section. Also refer to
the illustrations and information in this section about
proper flame pattern and spiderscreens.
SYMPTOM
• The smell of gas and/or a light hissing sound.
CAUSE SOLUTION
The internal rubber seal in the LPG cylinder valve
could be damaged.
Inspect the rubber seal for damage. If damaged,
return LPG cylinder to local retailer.

20
Troubleshooting
REPLACEMENT
PARTS
To obtain replacement parts,
contact the local retailer in your
area or log onto weber.com.
CALL
CUSTOMER
SERVICE
If you are still experiencing any
problems, contact the CustomerService
Representative in your area using
the contact information on
weber.com.
GREASY BARBECUE (Peeling Paint & Flare-Ups)
SYMPTOM
• Inside of lid appears to have the appearance of peelingpaint.
CAUSE SOLUTION
The flakes you see are accumulated cooking vapours
that have turned into carbon.
This happens over time after repeated use of your
barbecue. This is not a defect. Clean the lid. Refer to
the “Product Care” section.
SYMPTOM
• Experiencing flare-ups when barbecuing or preheating.
CAUSE SOLUTION
There is leftover food from the previous meal. Always preheat the barbecue on the highest setting for
10to 15 minutes.
The inside of the barbecue needs to be cleaned
thoroughly.
Follow the steps in the "Cleaning and Maintenance"
section to clean the barbecue inside from the top
down.
LIGHTED CONTROL KNOBS
SYMPTOM
• Control knobs do not turn on after pressing power button.
CAUSE SOLUTION
Batteries are old. Install new batteries. Refer to “Replacing Batteries
for the Lighted Control Knobs” on this page.
Replacing Batteries for the Lighted
Control Knobs
Use alkaline batteries only. Do not mix old and new
batteries or dierent types of batteries (standard,
alkaline, or rechargeable). If you do not plan to use the
light for a month or more, remove the batteries.
1) Locate the battery housing on the inside of the
cabinet on the bottom right side.
2) Turn battery housing anti-clockwise to open (A).
3) Replace three D batteries (B).

21
FPO
AAA
AAA
AAA
Troubleshooting
GRILL LIGHT
SYMPTOM
• Grill light does not turn on.
CAUSE SOLUTION
The grill light will only activate when lid is open. Lift the lid to the open position and press the
awakebutton.
Batteries are old. Install new batteries. Refer to “Replacing Batteries
in the Grill Light” on this page.
SYMPTOM
• Grill light turned off and will not turn back on.
CAUSE SOLUTION
The grill light is programmed to turn o automatically
after thirty minutes of inactivity.
Reactivate the grill light. Open lid and press the
awakebutton.
SYMPTOM
• Grill light does not turn off.
CAUSE SOLUTION
The awake button will not turn the grill light o. The grill light is equipped with a tilt sensor. To turn the
light o, put the lid in the closed position.
Refer to “Using the Grill Light” in the “Operation”
section of thismanual.
Replacing Batteries in the Grill Light
Use alkaline batteries only. Do not mix old and new
batteries or dierent types of batteries (standard,
alkaline, or rechargeable). If you do not plan to use the
light for a month or more, remove the batteries.
1) Remove the light from the bracket with a philips
screwdriver (A).
2) Slide out battery compartment and replace three
AAA batteries (B).
3) Replace light onto bracket (C).