Weber PLATINUM 42370 User manual

THIS GAS APPLIANCE IS DESIGNED
FOR OUTDOOR USE ONLY.
42370 US 10/01/05
NG
LOCATING YOUR GRILL
When determining a suitable location for your Summit®gas grill installation, give attention to concerns such as exposure to wind, proximity to traffic paths, and
keeping any gas supply lines as short as possible. Never locate the Summit®gas grill in a garage, breezeway, shed, under an unprotected overhang, or other
enclosed area. Locate the grill and structure so there is enough room to safely evacuate the area in case of a fire.
CLEARANCE FROM SURFACES OR STRUCTURES
WARNING: Clearance from any surface or structure is
24 inches (609.6 mm) from the back and sides of the grill.
Refer to “Typical Gas Supply Installation” before starting
installation.
WARNING: The structure, “island”, countertops, and
adjacent work areas for the built-in grill installation must be
built from noncombustible materials only.
NOTE: If you have questions on what materials are considered noncombustible,
contact your local building materials supplier or fire department.
A
ny
S
ur
f
ace
Any Surface
24 inches (61 cm) Any Surface
24 inches (61 cm)
24 inches (61 cm)
Grill Frame
Note: For a countertop treatment: Recommended 3/4 inch
(
19.1 cm) overhang. Notch front edge for frame to fully
slide in.
27 inches (685.8 mm) min. for
lid clearance
1
3
2
BUILT-IN NG GAS GRILL INSTALLATION GUIDE
PLATINUM D4 / D6
SUMMIT®
BUILT-IN STRUCTURE CUTOUT DIMENSIONS
ALL DIMENSIONS ARE TO FINISHED SURFACES.
WARNING: All countertop finished surfaces must be
constructed of a noncombustible material.
Built-In Cutout Dimensions
D4 D6 Tolerances
130
1/4
˝ 38
1/4
˝+
1/4
” -
1/4
˝
234
1/4
˝ 34
1/4
˝+
1/4
” -
1/4
˝
321˝ 21˝ +
1/4
” -
1/4
˝
42370
42370_NG BIinstll.indd 1 9/23/05 11:08:10 AM

2
30 1/4"
Built-In
Frame
34 1/4"
24"
min.
21"
Access for electric
on left hand side
6
1/4"
3 3/4"
Gas Inlet
Note: For a countertop treatment:
Recommended 3/4inch overhang.
Notch front edge for frame to fully slide in.
6 1/4"
3 3/4"
Gas Inlet
24"
min.
24"
min.
*Clearance from any surface or structure is at least 24 inches from the back and
sides of the grill.
27 inches min.
distance from front
edge of the cutout
for open lid clearance
10 1/2"
min.
Side Burner
Opening
4B
38 1/4"
Built-In
Frame
34 1/4"
24"
min.
21"
Access for electric
on left hand side
6
1/4"
3 3/4"
Gas Inlet
Note: For a countertop treatment:
Recommended 3/4inch overhang.
Notch front edge for frame to fully slide in.
6 1/4"
3 3/4"
Gas Inlet
24"
min.
24"
min.
*Clearance from any surface or structure is at least 24 inches from the back and
sides of the grill.
27 inches min.
distance from front
edge of the cutout
for open lid clearance
10 1/2"
min.
Side Burner
Opening
6B
GENERAL CONSTRUCTION DETAILS
Summit®Built-In unit and all other accessory units should be on site before construction begins. All dimensions have a tolerance of plus or minus (+/-)
1/4
inch.The grill frame rests directly on the Island Structure top finished surface. Make sure this surface is level. Do not support the grill from the bottom. If the
supporting structure is going to have an electrical outlet for a rotisserie, it should be on the left side of the structure.
BUILT-IN CUTOUT DIMENSIONS
42370_NG BIinstll.indd 2 9/23/05 11:08:16 AM

3
PARTS LIST
Lid - 1
Cookbox - 1
Bottom Shelf - 1
Rear Panel
Assembly- 1
Left Door - 1
Right Door - 1
Warming Rack - 1
Warm-Up™Rack - 1
Front Frame Rail - 1
Rear Frame Rail - 1
Right Enclosure Panel - 1
Left Enclosure Panel - 1
Front Vent Panel - 1
Lid - 1
Cookbox - 1
OR
Rear Vent - 1
4B
6B
42370_NG BIinstll.indd 3 9/23/05 11:08:17 AM

4
Rotisserie Bracket - 1
Flavorizor®Bars - 2 Sets
Smoker - 1
Stainless Steel
Cooking Grates
Bottom Tray - 1
Catch-Pan Holder - 1
Catch-Pan - 1
Disposable Drip Pans - 2
Rotisserie - 1
Rotisserie Motor - 1
7/16 inch Wrench - 1
1/2 inch Bolts
(1/4 x 20 x 1/2 inch Bolt) - 8
Hinge Pin- 2
Hair Pin Cotter- 2
Wrench - 1
Nylon Washer - 8
#10-32 x 1/4 inch Steel Screws - 5
x10 Sheet Metal Screws - 3
Plastic Anchors - 3
- 2
- 3
Corrugated gas line - 1
Keps Nuts (1/4 x 20 Blk Zinc) - 2
Rotisserie Bracket Hardware- 2
Right Front Vent Clip - 1
Left Front Vent Clip - 1
1/2" Flare Gasket - 2
3/8" Flare Gasket - 2
Handle - 2
Handle Hardware - 4
PARTS LIST (CONTINUED)
6B
4B
42370_NG BIinstll.indd 4 9/23/05 11:08:21 AM

5
EXPLODED VIEW - PLATINUM D4
48
1
2
5340501 - Summit®Platinum D4 NG Built-In 091905
17
18
19
21
38
39
40
62
63
64
45
27
42
4
14
20
22
23
24
16
13
57
56
60
3
6
26
65
12
5
7
55
25
15
58
41
43
44
46
47
49
50
51
10
9
8
52
53
54
11
66
68
69
70
76
77
28
29
30
31
33
34
35
67
36
71
72
74
75
61
59
37
73
32
42370_NG BIinstll.indd 5 9/23/05 11:08:23 AM

6EXPLODED VIEW LIST - PLATINUM D4
1. Hinge Pin
2. Thermometer Hardware
3. Thermometer Bezel
4. Warm-Up™Basket
5. Smoker Assembly
6. Flavorizer®Bar Assembly w/ Smoker
7. Smoker Box Chip Grate
8. Rotisserie Motor
9. Motor Bracket
10. Motor Bracket Screw
11. 1/4 - 20 inch Keps Nut
12. Smoker Electrode Assembly
(10 1/2 inch wire)
13. Electrode Assembly (8 3/4 inch wire)
14. Crossover®Tube
15. Smoker Burner Tube
16. Left Burner Tube
17. 10 - 24 x 1/2 inch Black Screw
18. Manifold
19. Negative Ignition Switch Wire
20. Positive Ignition Switch Wire
21. Four Output Ignition Module Assembly
22. Ignition Switch Button Assembly
23. 10 - 24 x 1/2 inch Black Screw
24. Small Control Knob
25. Control Knob
26. Control Panel
27. Front Panel
28. Vent Cover Assembly
29. Front Frame Rail
30. Left Rear Panel
31. Left Panel
32. Handle Assembly
33. Bottom Shelf
34. Toe Kick Vent
35. Left Vent Bracket
36. Left Door Assembly
37. Right Door Assembly
38. Hair Pin Cotter
39. Lid Assembly
40. 1/4 - 20 x 1 1/4 inch Bolt
41. IR Rain Cover Hardware
42. 12 inch Cook Grate
43. IR Rain Cover
44. 10 - 24 x 1/2 inch Stainless Steel Screw
45. Right Flavorizer®Bar Assembly
46. IR Burner
47. IR Cover Box
48. Warming Rack
49. Thermocouple
50. IR Gas Line
51. IR Electrode Wire
52. Rotisserie Fork Screw
53. Rotisserie Fork
54. Rotisserie Shaft
55. Cookbox Assembly
56. Electrode Assembly (16 1/4 inch wire)
57. Right Burner Tube
58. Heat Shield
59. Battery Shield Assembly
60. Main Gas Line
61. Bulkhead Assembly
62. Bottom Tray
63. Summit Catch Pan Holder
64. Summit Catch Pan
65. Summit Drip Pan
66. Rear Frame Rail
67. Rear Vent Hardware
68. Rear Panel Hardware
69. Right Rear Panel
70. Right Panel
71. 10 -16 x 3/4 Screw w/ Washer
72. Plastic Plug
73. Door Stop
74. Door Bushing
75. Door Plug
76. 1/4 - 20 x 1/2 inch Black Bolt
77. Right Vent Bracket
42370_NG BIinstll.indd 6 9/23/05 11:08:23 AM

7
EXPLODED VIEW - PLATINUM D6
8
50
1
2
5390501 - Summit®Platinum D6 NG Built-In 092005
17
20
21
22
24
42
43
44
58
65
66
67
68
69
47
30
52
9
10
13
12
45
4
6
7
16
23
26
27
28
29
53
55
18
14
15
51
56
60
59
62
57
3
48
49
54
46
19
11
5
25
61
71
72
73
78
79
31
32
33
35
37
38
39
70
40
74
75
76
77
36
41
63
64
34
42370_NG BIinstll.indd 7 9/23/05 11:08:24 AM

8EXPLODED VIEW LIST - PLATINUM D6
1. Hinge Pin
2. Thermometer Hardware
3. Thermometer Bezel
4. Warm-Up™Basket
5. 8 inch Cooking Grate
6. Smoker Assembly
7. Smoker Box Chip Grate
8. Flavorizer®Bar Assembly w/ Smoker
9. Rotisserie Fork
10. Rotisserie Motor
11. Motor Bracket
12. Motor Bracket Screw
13. 1/4 - 20 inch Keps Nut
14. Smoker Electrode Assembly
(10 1/2 inch wire)
15. Electrode Assembly (8 3/4 inch wire)
16. Crossover®Tube
17. Smoker Burner Tube
18. Left Burner Tube
19. Right Burner Tube
20. 10 - 24 x 1/2 inch Black Screw
21. Manifold
22. Negative Ignition Switch Wire
23. Positive Ignition Switch Wire
24. Six Output Ignition Module Assembly
25. Ignition Switch Button Assembly
26. 10 - 24 x 1/2 inch Black Screw
27. Small Control Knob
28. Control Knob
29. Control Panel
30. Front Panel
31. Vent Cover Assembly
32. Front Frame Rail
33. Left Rear Panel
34. Handle Assembly
35. Left Panel
36. Door Stop
37. Bottom Shelf
38. Left Vent Bracket
39. Toe Kick Vent
40. Left Door Assembly
41. Right Door Assembly
42. Hair Pin Cotter
43. Lid Assembly
44. 1/4 - 20 x 1 1/4 inch Bolt
45. 12 inch Cook Grate
46. IR Rain Cover Hardware
47. Right Flavorizer®Bar Assembly
48. IR Rain Cover
49. 10 - 24 x 1/2 inch Stainless Steel Screw
50. Warming Rack
51. Rotisserie Fork Screw
52. IR Burner
53. IR Cover Box
54. Thermocouple
55. IR Gas Line
56. Rotisserie Shaft
57. IR Electrode Wire
58. Cookbox Assembly
59. Electrode Assembly (16 1/4 inch wire)
60. Electrode Assembly (25 1/2 inch wire)
61. Heat Shield
62. Main Gas Line
63. Battery Shield Assembly
64. Bulkhead Assembly
65. Bottom Tray
66. Summit Catch Pan Holder
67. Summit Catch Pan
68. Summit Drip Pan
69. Rear Frame Rail
70. Rear Vent Hardware
71. Rear Panel Hardware
72. Right Rear Panel
73. Right Panel
74. 10 -16 x 3/4 Screw w/ Washer
75. Plastic Plug
76. Door Bushing
77. Door Plug
78. 1/4 - 20 x 1/2 inch Black Bolt
79. Right Vent Bracket
42370_NG BIinstll.indd 8 9/23/05 11:08:24 AM

9
1
1
2
2
3
1
2
ATTENTION!
Do not fully tighten screws.
Clips should slide freely
when installed
ASSEMBLY
Arrow stickers on
Frame Rail (1) and
Left Side Panel (2)
should point toward
each other (shown
above). Door Stop
Bracket (3) should
be positioned as
shown (left).
42370_NG BIinstll.indd 9 9/23/05 11:08:25 AM

10
3
4
ASSEMBLY
42370_NG BIinstll.indd 10 9/23/05 11:08:26 AM