Weefine WFA03 User manual

Please read the manual carefully before using the remote control
Specifications
Instructions
To install the battery
Battery:1*CR123A
Depth rating:80m
Weight:115g on land 40g underwater
Dimension:68.5(L) x 47.2(W) x 34.8(H)mm
Trip Mount:Standard 1/4-20 trip threads
Step 1: Turn the tail cap counter-clockwise to open.
Step 2: Put the CR123A battery into the battery compartment
(as shown in the diagram below).
Step 3: Turn the tail cap clockwise to close the battery compartment.
Important: After you install the battery three blue indicators will
light up automatically. The middle indicator light will slowly
flash. If the remote control is not immediately used the indicators
will turn off automatically a few seconds later.
The indicators tell you what mode you are in and whether or not
the remote control is turned on.
Overview of how to use the remote control
L1 Remote Control Indicator L2 Remote Control Indicator
Middle (mode) Iindicator
Remote control for Video Light
WFA03
Overview
Components
Your new Remote Control is designed for use with Weefine
Video Lights .
Right Button
Middle Button
Left Button
Tail Cap
Remote control Output L2
Remote control Output L1
Battery Compartment
3*Standard 1/4-20 trip threads
1.Do not open the tail cap when using in the water.
2.If the remote control will not be used for a long period of time the battery
should be removed.
Warning
General Maintainence
Warranty
If the O-ring is damaged, broken or deformed it should be replaced with
the a new O-ring. One spare O-ring is included when you purchase your
remotecontroller.
Note: Do not use a sharp tool to remove the O-ring.
Weefine provides a warranty against manufacturer defects for 18 months
starting from the date of purchase. Manufacturer defects occuring within 15
days of the date of purchase will result in an exchange of product at the
vendor. All other manufacturer defects occuring within 18 months of the
purchase will be repaired at no cost. Proof of purchase is required for warranty
support. The warranty does not cover failures or defects resulting from misuse
(e.g., modification; damage), natural disasters, or battery issues, including
incorrect battery installation.
L1 Remote Control Indicator
L2 Remote Control Indicator
To use the remote control with a video light
The L1 Remote Contol operates the device connected on the left. To turn the
L1 Remote Control on or off, press the left button and hold it for two seconds.
If you turn the L1 Remote Control off the indicator light will turn off and you
will not be able to control the device on the left hand side.
The L2 Remote Contol operates the device connected on the right. To turn the
L2 Remote Control on or off, press the right button and hold it for two
seconds. If you turn the L2 Remote Control off the indicator light will turn off
and you will not be able to control the device on the right hand side.
You can use your remote control with the following video lights:
Smart Focus 2300, Solar Flare 2800, Solar Flare 3800 or Solar Flare Max.
Step 1: Connect the remote controller and the video light with the fiber optic
cable.
Step 2: Turn on the video light.
To increase the brightness: Press the right button for less than one second.
To decrease the brightness: Press the left button for less than one second.
To switch mode: Press the middle button for less than one second.
To turn the L1 Remote Control on / off: Press and hold (for 2 seconds) the left
button. When the L1 output is off the L1 indicator light will be off.
To turn the L2 Remote Control on / off: Press and hold (for 2 seconds) the
right button. When the L2 output is off the L2 indicator will be off.
To turn sleep mode on / off: Press and hold the middle button for more than
one second. When the video light is in sleep mode, you can reactivate the light
using the remote control or by manually turning the video light on or off to
reset.
1
02 03
Warning!! The polarity of the battery
must match the polarity of the contacts
in the battery compartment. Make sure
that the positive and negative poles of
the battery align with the positive and
negative poles of the remote control.

使用遥控器前请详细阅读使用说明书
** 电池装入遥控器须装配到位，并注意电
池的正负极标识，请勿装反。电池安装
后，指示灯闪烁5秒后熄灭，遥控器就绪；
规格
电池安装
电池型号：1*CR123A
防水深度：80米
重量：115g （陆地） 40g （水下）
产品尺寸：68.5(长) x 47.2(宽) x 34.8(高) 毫米
标准转接座：Standard 1/4-20 trip threads
1. 按逆时针方向旋转打开电池盖；
2. 按照下图演示，将CR123A电池放入电池仓中；
3. 按顺时针方向旋转拧紧电池盖。
安装电池后，三个蓝色指示灯将自动亮起. 模式指示灯慢闪烁.
如果未立即使用遥控器，则指示灯几秒后自动关闭。
指示灯指示您处于何种模式，以及告诉您遥控器是否处于已打开。
操作说明
L1 遥控器指示灯 L2 遥控器指示灯
模式指示灯
支持机型
产品组件
此遥控器只适用Weefine设计的摄影灯
上调按钮
模式按钮
下调按钮
电池盖
信号发射端口 L2
信号发射端口 L1
电池仓
遥控器固定座
1
02 03
1、不得使用产品要求以外的任何电池；
2、潜水时，电池盖不可拧开；
3、长时间不使用遥控器，请将电筒内的电池取出。
注意事项
保养
品质保证
当发现防水O-Ring有破损、破裂或变形时，将不良的O-Ring取出，换上配备的
O-Ring。注意不得用锋利的工具操作，以免损伤防水O-Ring。更换时要清除干净密
封位置的。
自购买日起18个月内，我们对制造商的缺陷提供保修；自购买日期后15天内发生
的制造商缺陷导致卖方产品的交换和所有其他制造商在采购18个月内出现的缺陷将免
费维修。购买证明需要保证支持。
保修不包括因使用不当而导致的故障或缺陷（例如：修改；损坏），自然灾害，
或电池问题，包括不正确的电池安装。
L1 通道指示灯
L2 通道指示灯
控制带有遥控功能的摄影灯
L1通道控制左边连接的设备
打开或关闭L1通道：长按下调按钮2秒
L1通道关闭后，指示灯将会熄灭，将无法控制左边连接的设备。
L2通道控制左边连接的设备
打开或关闭L2遥控器：长按上调按钮2秒
L2通道关闭后，指示灯将会熄灭，将无法控制左边连接的设备。
遥控器可以连接以下型号的摄影灯
Smart Focus 2300 / Solar Flare 2800 / Solar Flare 3800 / Solar Flare Max
第一步:用光纤线连接遥控器和摄影灯。
第二步:打开摄影灯
增加亮度: 短按上调按钮
减少亮度: 短按下调按钮
模式切换: 短按模式按钮
开启/关闭L1端口 : 长按下调按钮2秒. 当L1 输出关闭时，L1指示灯将关闭。
开启/关闭L2端口 : 长按上调按钮2秒. 当L2 输出关闭时，L2指示灯将关闭。
开启/关闭睡眠模式: 长按模式按钮1秒；当视频灯处于睡眠模式时，您可以使用遥控器
重新激活灯光，也可以手动打开或关闭摄影灯进行重置。
摄影灯遥控器
WFA03