Weider PRO 9930 User manual

Patent Pending
Model No. 831.159720
Serial No.
The serial number is found in the
location shown below. Write the
serial number in the space above.
Serial
Number
Decal
EXERCISE
EQ u t P M F---.NT
Jell JR I| I |el _.
HELPLINE!
/-800-736-6879
USER'S MANUAL
SEARS, ROEBUCK AND CO.
HOFFMAN ESTATES, IL 60179
www.weid,.,rfitness.com
new products, prizes,
fitness tips, and much more!

important Precautions ................................................................... 3
Before You Begin ...................................................................... 4
Assembly ............................................................................ 5
Cable Diagrams ...................................................................... 19
Adjustment .......................................................................... 21
Trouble-shooting and Maintenance ........................................................ 22
Weight Resistance Chart ....... "......................................................... 23
Ordering Replacement Parts ...................................................... Back Cover
Full 90-day Warranty ............................................................ Back Cover
Note: A PART LIST/EXPLODED DRAWING and a PART IDENTIFICATION CHART are attached in the center of
this manual. Remove the PART LIST/EXPLODED DRAWING and the PART IDENTIFICATION CHART before
beginning assembly.
2

3

Thank you for selecting the innovative and versatile
WELDER° PRO 9930 Home Gym. The WELDER ° PRO
9930 offers a unique selection of weight stations
designed to develop every major muscle group of the
body. Whether your goal is to tone your body, build
dramatic muscle size and strength or improve your
cardiovascular system, the WELDER° PRO 9930 will
help you to achieve the results you want.
For your benefit, read this manual carefully before
using the WELDER®PRO 9930 Home Gym. If you
have additional questions, please call our toll-free
HELPLINE at 1-800-736-6879, Monday through
Saturday, 7 a.m. until 7 p.m. Central Time (excluding
holidays). To help us assist you, please note the prod-
uct model number and serial number before calling.
The model number is 831.159720. The sedal number
can be found on a decal attached to the WELDER ®
PRO 9930 Home Gym (see the front cover of this
manual).
Please use the drawing below to familiarize your-
self with the major parts and how they fit together,
ASSEMBLED
DIMENSIONS:
Height: 78 in.
Width: 65 in.
Depth: 34 in.
Butterfly
Backrest
Curl
Adj
Knob
Low Pulley
Lat Bar
High Pulley
Station
Backrest
Seat
Leg Press
Lever
Foot Plate
Weight
Stack
4

Note: This introduction will save you more time
than it takes to read itt
Some assembly ste_s require two people.
Giving Yourself a Good Start
Before you begin the assembly process itself, take
the time to complete the steps outlined here.
Clearing the Workspace
Clear a workspace that is large enough to hold all
parts and allow you to walk all the way around the
assembled equipment.
Unpacking the Box
To make the assembly process as smooth as possi-
ble, we have broken it into separate stages. All parts
used in each stage are found in individual packages
in the shipping box. Place all parts in a cleared area
and remove the packing materials. Do not dispose of
the packing materials until assembly is completed.
Important: Wait until you begin each assembly
stage to open the parts bag labeled for that
assembly stage.
Identifying Parts
To help you identify the small parts used in assem-
bly, we have included a PART IDENTIFICATION
CHART located in the center of this manual. Place
the chart on the floor or work table and use it to
quickly identify different parts for each step. Note:
Some small parts may have been pre-attached for
shipping. If a part is not in the parts bag, check to
see if it has been pre-attached.
Orienting Parts
As you assemble this product, be sure that all parls
are oriented as shown in the drawings.
Tightening Parts
Tighten all parts as you assemble them, unless
instructed to do otherwise.
Lining Up the Tools
Assembly requires the following tools (not included):
• Two (2) adjustable wrenches
• One (1) standard screwdriver _=._==,(_
• One (1) phillips screwdriver
• One (1) rubber mallet
• Lubricant, such as grease or petroleum jelly,
and soapy water
• Tape, such as clear tape or masking tape
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end wrenches
or aset of ratchet wrenches.
w
The Four Stages of the Assembly Process
Frame Assembly
You will begin by assembling the base and the
upright frames that serve as the skeleton of the
equipment.
Cable Assembly
This assembly completes the cables and pulleys
that connect the moving arms with each other and
with the weights.
Arm Assembly
This assembly completes the press and butterfly
arms that you operate while you are exercising.
Seat Assembly
This assembly completes the seat and backrest
that support your body while you are exercising_
5

1
1. Before beginning, make sure that you have read
and understood the information on page 5.
Locate and open the parts bag labeled "FRAME
ASSEMBLY."
Press a 2" Square Inner Cap (38) into the Butterfly
Base (61). Press two 2" Square inner Caps (38) into
the Press Base (60).
Insert four 5/16" x 2 1/2" Carriage Bolts (1) up
through the indicated holes in the Butterfly Base (61)
and the Press Base (60). Note: If the Bolts fall out,
secure them by putting asmall piece of tape over
• the head of each Bolt, Place the Butterfly Base and
Press Base flat on the floor.
Attach the Press Base (60) to the Butterfly Base (61)
with two 5/16" x 2 1/2" Botts (3), two 5/16" Flat
Washers (19), and two 5/16" Nylon Locknuts (2).
2. Position the Butterfly Upright (62) as shown. Place
the bracket on the lower end of the Butterfly Upright
(62) over the indicated 5/16" x2 1/2" Carriage Bolts
(1) in the Butterfly Base (61). Hand tighten two 5/16"
Nylon Locknuts (2) onto the Bolts. Do not tighten the
Nylon Locknuts yet.
Place the bracket on the lower end of the Press
Frame Upright (59) over the indicated 5/16" x 2 1/2"
Carriage Bolts (1) in the Press Base (60). Hand tight-
en two 5/16" Nylon Locknuts (2) onto the Bolts. Do
not tighten the Nylon Locknuts yet.
38 19 3
61 60
38
21
2
Position
with the
6

" "3.-'Place _vo'_/e!ghi Burn'pers (8_ over'the indicated -"
holes in the Butterfly Base (61). Slide the Weight
Guides (58) into the indicated holes.
Attach the Weight Guides (58) to the Butt_;iy Base
(61) with two 3/8" x 2 1/2" Bolts (6), four 3/8" Flat
Washers (17), and two 3/8" Jam Nuts (18).
Slide the eight Weights (8) onto the Weight Guides
(58). Make sure the Weights are turned so the pin
grooves are on the bottom of the weights.
3
Pin
61
6
58
4.
5°
Press a Weight Tube Bumper (76) into tiie lower end
of the Weight Tube (77). Slide the Weight Tube into
the center hole in the Weights (8).
Lubricate the holes in the Top Weight (78). Slide the
Top Weight onto the Weight Guides (58).
Press a 2" Square Inner Cap (38) into the Butterfly
Top Frame (64). Press two 1" Round Inner Caps (41)
into the top of the Butterfly Top Frame.
Attach the Butterfly Top Frame (64) to the Press Top
Frame (63) with two 5/16" x 2 1/2" Bolts (3), two 5/16"
Flat Washers (19), and two 5/16" Nylon Locknuts (2).
Press a 2" Square Inner Caps (38) into the end of the
Press Top Frame (63).
4Lubricate
!! °
n
_ o
41 64
38
2
\2
/38
63
7

_._ Hold-the Butteflly -TopFrame-(64) and the Press Top
Fr._r:ne(63)-on the indicated brab'kets on"the Uprights
(59, 62) and the Weight Guides (58)• Note: Before
attaching the Top Frames to the Uprights, make
sure that both Weight Guides (58) are positioned
inside of the indicated holes.
Attach the Butterfly Top Frame (64) and the Press
Top Frame (63) to the Uprights (59, 62) and Weight
Guides (58) with four 5/16" x 2.3/4" Bolts (20), two
Top Plates (46), and four 5/16" Nylon Locknuts (2).
Do not tighten the Nylon Locknuts yet.
Secure the Weight Guides (58) to the Butterfly Top
Frame (64) and to the Press Top Frame (63) with two
3/8" x 2 1/2" Bolts (6), four 3/8" Flat Washers (17),
and two 3/8" Jam Nuts (18).
6
2O
io
62 f
58--< -----. _',
r.
_o'1 O
_-_2 _,.__.
59_
7, Turn the Seat Brace (75) so the nut is on the side as
shown. Attach the Seat Brace (75) to the Butterfly
Base (61) with the 5/16" x 2 1/2" Carriage Bolts (1)
and two 5/16" Nylon Locknuts (2). Do not tighten the
Nylon Locknuts yet.
7
61
8. Hold the Seat Bar (74) between the Seat Brace (75)
and the Butterfly Upright (62) so that the hole that is
closest to the welded plate is facing the Seat Brace.
Attach the Seat Bar (74) to the Seat Brace (75) with
two 5/16" x 2 1/2" Bolts (3), two 5/16" Flat Washers
(19), and two 5/16" Nylon Locknuts (2). Do not over-
Ugten the Bolts or the Curl Post attached in step
38 will not slide freely. Do not tighten the Nylon
Locknuts yet.
Attach the Seat Bar (74) to the Butterfly Upright (62)
with two 5/16" x 2 1/2" Bolts (3), two 5/16" Flat
Washers (19), and two 5/16" Nylon Locknuts (2).
Important: Go back and tighten all of the Nylon
Locknuts used in steps 1 through 8.
Hole /_] }'l ]o_._3
74 /"/ !
ii 6ii '1°
8

9_ Locate and open the pg,,Is bag labeled "ARM
ASSEMBLY."
See the inset drawing. Orient the Press Frame (53) as
shown. Lubricate a 3/8" x 8" Bolt (30). Attach the
Press Frame to the Press Base (60) with the 3/8" x 8"
Bolt, two 1" x 7/8" Plastic Bushings (29), and one 3/8"
Nylon Locknut (4). Do not overtighten the 3/8"
Nylon Looknut. The Press Frame must pivot easily.
iO. Press a 1 3/4" Square Inner Cap (37} into the top of a
Press Arm (54). Press a 1" Inner Cap (80) into the
indicated hole in the Press Arm.
Attach the Press Arm (54) to the bracket on the Press
Frame (53) with two 5/16" x 2 1/2" Bolts (3) and two
5/16" Nylon Locknuts (2).
Repeat this step to assemble the second Press Arm
(54).
3O
Lubricate
11. Press a I 1/2" Inner Cap (79) into the Press Seat
Frame (52).
Slide the bracket on the Press Seat Frame (52) onto
the indicated 5/16" x 2 1/2" Carriage Bolts (1) in the
Press Base (60). Tighten two 5/16" Nylon Locknuts
(2) onto the Bolts.
Attach the Press Seat Frame (52) to the Press Frame
Upright (59) with two 5/16" x 2 3/4" Bolts (20), two
5/16" Flat Washers (19), and two 5/16" Nylon
Locknuts (2).
79
6O
9

_12. PreS's-two.1 1/2_'SqeaFe Irme_ Caps-(79) into the Eeg _ "
Le_,er (49), -
Insert aBumper (33) between the brackets on the Leg
Lever (49). Secure the Bumper to the Leg Lever with a
#10 x 1" Screw (32).
Slide the bracket on the Leg Lever (49) onto the Press
Seat Frame (52). Attach the Leg Lever to the Press Seat
Frame with a 5/16" x 2 1/4" Bert (81) and a 5/16" Jam
Nut (90). Do not overtighten the 5116" Jam Nut. It
must be easy for the Leg Lever to pivot.
Attach a 3/8" x 2 1/2" Eye Bolt (B3) to the Leg Lever (49)
with a 3/8" Flat Washer (17) and a 3/8" Nylon Locknut
13. Press a 1 3/4" Square Inner Cap (37) into each end of
• the Right Butterfly Arm (68). Wet the lower end of the
Arm with soapy water. Slide a 10" Pad (65) onto the
lower end of the Arm.
Lubdcate the indicated axle on the Butterfly Top Frame
(64). Orient the Right Butterfly Arm (68) as shown and
slide it onto the axle. Secure the Butterfly Arm with two
1" Retainers (25) and a 1" Round Cap (26). Note: Place
the Retainer Rings on top of the inverted Round Cap
and gently tap the Cap onto the axle with a hammer,
Make sure the teeth on the Retainer Rings bend
towards the Cap as shown in the inset drawing.
Repeat this step to assemble the Left Butterfly Arm (67).
14. Locate and open the parts bag labeled "CABLE
ASSEMBLY AND PULLEYS." For Cable Identification
and routing during steps 14 to 32, refer to the Cable
Diagrams and Cable ID Chart on pages 19 and 20.
Insert two 3/8" x 1" Bolts (15) into the welded brackets
on the Left and Right Butterfly Arms (67, 68), Secure the
Bolts with a3/8" Jam Nut (18).
Identify the Short Cable (71). It is approximately 74 1/2"
long and it has a closed loop on each end. Slide one
end of the cable onto each of the 3/8" x 1" Bolts (15).
Secure the Cable to the Bolts with 3/8" Jam Nuts (18).
Do not overtighten the Nylon Jam Nuts.
Remove both 31/2" Pulleys (5) from the pre-assembled
Adjustable Pulley Plates (44). Wrap the Short Cable (71)
around a 3 1/2" Pulley (5) in the direction shown. Attach
the 3 1/2" Pulley and a Cable Trap (39) to the top hole in
the two Adjustable Pulley Plates (44) with a 3/8" x 2" Bolt
(35) and a 3/8" Nylon Locknut (4). Make sure the Cable
Trap and Pulley Plates are oriented as shown.
10

15. Wrap the Short Cable over a"V" Pulley'(21) as_-,
shown. Attach the "V" Pulley and a Long Cable Trap
(14) to one side of the welded bracket on the Butterfly
Upright (62) with a 3/8" x 2 1/2" Bolt (6) and a 3/8"
Nylon Locknut (4).
Attach another "V_ Pulley (21) and a Long Cabte Trap
(14) to the other side of the welded bracket on the
Butterfly Upright (62) in the same manner.
16. Identify the Medium Cable (72). It is approximately
140" long and it has a ball on one end and a threaded
shaft on the other. Wrap the Medium Cable over the 3
1/2" Pulley (5),as shown. Attach the Pulley to the
Press Top Frame (63) with a 3/8" x 3 1/2" Bolt (24),
one 3/8" Flat Washer (17), and a 3/8" Jam Nut (18).
Make sure the Medium Cable (72) is between the
3 1/2" Pulley (5) and the welded pin on the Press
Top Frame (63).
15
16
Bracket
63
Pin
17
24
17. Wrap the Medium Cable (72) over a 3 1/2" Pulley (5)
as shown. Attach the 3 1/2" Pulley and a Cable Trap
(39) to the Press Top Frame (63) with one 3/8" x
3 3/4" Bolt (7).
17 5
39
63
18. Route the threaded shaft on the Medium Cable (72)
under one of the 31/2" Pulleys (5) that is already
mounted in the Double =U" Bracket (36). Tighten the
3/8" x 1 3/4" Bolt (22).
18
7 22
11

_19. Wra{:):the Mediur_Cable (72)-over a 4 1/2" Pulley -.
(34) in the c]irection shown. Atta'¢h the Pulley to the
Butterfly Top Frame (64) with a 3/8" x 1 3/4" Bolt (22)
and a 3/8" Nylon Locknut (4).
20. Attach the threaded shaft on the Medium Cable (72)
to the Small "U"-Bracket (43) with a 1/4" Flat Washer
(11) and a 1/4" Nylon Locknut (16). Note: See the
inset drawing. Do not completely tighten the
Nylon Locknut; it should be threaded only two
turns onto the end of the Cable.
Attach the Small "U"-Bracket (43) to the hole in the
Weight Tube (77) with a 5/16" x 1 3/4" Bolt (9), and a
5/16" Nylon Locknut (2).
21. Identify the Long Cable (73). It is approximately
299.25" long and it has a ball on one end and a loop
on the other. Route the end with the loop through the
slot in the cable guide on the Butterfly Base (61).
Route the Long Cable (73) under a 3 1/2" Pulley (5)
as shown• Attach the Pulley and a Cable Trap (39) to
the indicated bracket on the Butterfly Base (61) with a
3/8' x 2" Bolt (35) and a 3/6" Nylon Locknut (4). Make
sure the Cable Trap is oriented as shown.
-21
73 39
12

-22._Wrap the'Long(_able'i73)'aro_nd a3 t/2" Pulley (5) ....
in the direction shown. Attach the Pulley and a Cable
Trap (39) to the Butterfly Upright (62) with a 3/8" x
3 3/4" Bolt (7), a 3/8" Flat Washer (17) and a 3/8"
Nylon Locknut (4). Make sure the Cable Trap is ori-
ented as shown.
Wrap the Long Cable (73) over a 3 1/2" Pulley (5) in
the direction shown. Re-attach the Pulley and a Cable
Trap (39) to the lower hole in the Adjustable Pulley
Plates (44) with a 3/8" x 2" Bolt (35) and a 3/8" Nylon
Locknut (4). Make sure the Cable Trap is oriented
as shown.
22
35
23. Wrap the Long Cable (73) around a 3 1/2" Pulley (5)
in the direction shown. Attach the Pulley and a Cable
Trap (39) to the indicated bracket on the Butterfly
Base (61) with a 3/8" x 2" Bolt (35) and a 3/8" Nylon
Locknut (4).
24. Wrap the Long Cable (73) around a3112" Pulley (5).
Attach the Pulley and a Cable Trap (39) to the indicat-
ed bracket on the Butterfly Base (61) with a 3/8" x 2"
Bolt (35) and a 3/8" Nylon Locknut (4).
23
24
35 4
61 Bracket
13

*25. Notd:.For.clarity,:thisand_he following drawings
sh_w someparts removed, ";
Remove the lower 3 1/2" Pulley (5) from the Double
"U" Bracket (36). Then, wrap the Long Cable (73)
over the Pulley (5) in the direction shown. Attach the
Pulley to the Double "U" Bracket (36) with a 3/8" x 1
3/4" Bolt (22) and a 3/8" Nylon Locknut (4). Make
sure the Double "U" Bracket is oriented as
shown.
25 - ""~:"
26. Wrap the Lollg Cable (73) around a 3 1/2" Pulley (5)
in the direction shown. Attach the Pulley and a Cable
Trap (39) to the indicated bracket on the Press Base
(60) with a 3/8" x 2" Bolt (35) and a 3/8" Nylon
Locknut (4). Make sure the Cable Trap is oriented
as shown.
27. Attach a 3 1/2" Pulley (5) and a Cable Trap (39) to
the Press Frame Upright (59) with a 3/8" x 4 3/4" Bolt
(23).
Wrap the Long Cable (73) around the 3 1/2" Pulley
(5) in the direction shown. Hand tighten a 3/8" Nylon
Locknut (4) two turns onto the 3/8" x 4 3/4" Bolt. In
step 31, another Pulley will be attached to the Bolt.
\4
I
F 73
5
28. Route the Long Cable (73) through the opening in the
Press Frame (63) and wrap the Long Cable around a
3 1/2" Pulley (5) in the direction shown. Then, route
the Long Cable back through the opening in the
Press Frame.
Attach the 3 1/2" Pulley (5) and a Cable Trap (39) to
the indicated hole in the Press Frame (53) with a 3/8"
x 3 1/4" Bolt (26), a 3/8" Flat Washer (17), and a 3/8"
Nylon Locknut (4). Make sure the Pulley is mount-
ed on the inside of the Press Frame (53). Make
sure the Cable Trap is oriented as shown.
38
14

"29-.'" wrap tl_e"Lon_) Cable" (73")around a:=V"-Pulley_21) ....
in the direction shown. Attach the "V"-Pulley and a
Large Cable Trap (14) to the small tube on the
Press Seat Frame (52) with a 3/8" x 3 1/4" Bolt (28),
a 3/8" Flat Washer (17) and a 3/8" Nylon Locknut
(4). Note: The small tube has three adjustment
holes. Mount the "V"-Pulley in the hole farthest
from the Upright. Make sure the Cable Trap is
oriented as shown.
4
30. Route the Long Cable (73) back through the opening
in the Press Frame (53) and wrap the Long Cable
around a 3 1/2" Pulley (5) in the direction shown.
Then, route the Long Cable back through the opening
in the Press Frame.
Attach the 3 1/2" Polley (5) and a Cable Trap (39) to
the indicated hole in the Press Frame (53) with a 3/8"
x 3 1/4" Bolt (28), 3/8" Flat Washer (17), and a 3/8"
Nylon Locknut (4). Make sure the Pulley is mount-
ed on the inside of the Press Frame. Make sure
the Cable Trap is oriented as shown.
73
31. Route the Long Cable (73) around a 3 1/2" Pulley (5)
and back through the opening in the Press Frame
(53).
Remove the 3/8" Nylon Locknut (4) from the 3/8" x 4
3/4" Bolt (23) that was inserted in step 27. Attach the
Pulley and a Cable Trap (39) to the Bolt and secure
the Pulley with the 3/8" Nylon Locknut (4). Make sure
the Cable Trap is oriented as shown.
31
_(_----5 23_
/
73
32. Note: Lift the top weight on the weight stack in
order to create slack in the Long Cable before
beginning this step.
Attach the Long Cable (73) to the Leg Lever (49),
slipping the looped end of the Cable through the
looped end of the Eye Bolt (83).
32
15

. . _:: ,#:_ ................... _ ............................... :............................. m: m ......................................................
............................o atA semb,y .............................
i!iiiiiiii!iiiiiiiiiiiiiii!ili::!ili!!iii_iiii!ii!i_iiii!iiiiiiiil_ i iii!: _ ii!i_!ili:iriiii!i!iiiiiiiii!ili_ili_i!iii_i:_i_iii!ii;ili:i!ii!!iiiilililill
33. Locateandopenthepa:tsbaglabeled"SEAT
ASSEMBLY."
Insert a 1/4" x 2" Carriage Bolt (85) through the cen-
ter hole in a Seat Plate (42). Attach the Seat Plate to
a Seat (51) with two 1/4" x 3/4" Screws (13).
Insert the 1/4" x 2" Carriage Bolt (85) into the indicat-
ed hole in the Press Seat Frame (52) and secure it
with a 1/4" Flat Washer (11) and a1/4" Nylon Locknut
(16). Secure the other end of the Seat (51) with a1/4"
x 2" Bolt (86) and a 1/4" Fiat Washer (11).
34. Press four 3/4" Round Inner Caps (40) into the ends
of the Pad Tubes (48) and the indicated tubes on the
Leg Lever (49) and the Press Seat Frame (52).
Insert the Pad Tubes (48) into the indicated holes in
the Leg Lever (49) and the Press Seat Frame (52).
Slide Foam Pads (47) onto the ends of the Pad
Tubes.
51
11 85
-42
52
34
4O
p_
35. Insert a 1/4" x2 1/2" Cardage Bolt (12) through the
center hole in a Seat Plate (42). Attach the Seat Plate
to the Press Backrest (89) with two 1/4" x 314" Screws
(13).
Insert the 1/4" x 2 1/2" Cardage Bolt (12) with a 1/4"
Flat Washer (11) into the indicated hole in the Press
Frame Upright (59) and secure it with a 1/4" Nylon
Locknut (16).
Secure the other end of the Press Backrest (89) with
a114"x 2 112" Screw (10) and a t/4" Flat Washer
bl).
42
89
16

" "36__nsert a :1/_,';"x 1-1/2" (_'arfiage'Bolt (82) "througlTthe_ "-"
center hole in a Seat Plate (42). Attach the Seat Plate
to a Seat (51) with two 1/4" x 3/4" Screws (13).
Insert the 1/4" x 1 1/2" Carriage Bolt (82) into the indi-
cated hole in the Seat Bar (74) and secure it with a
1/4" Flat Washer (11) and a 1/4" Nylon Locknut (16).
Secure the other end of the Seat (51) with a 1/4" x
1 1/2" Screw (68) and a 1/4" Flat Washer (11).
51\
42 74
88
37. Attach the Backrest (66) to the indicated holes in the
Butterfly Upright (62) with two 1/4" x 2 1/2" Screws
(10) and two 1/4" Flat Washers (11).
37
66
38. Attach the Curl Pad (69) to the Curl Post (70) with two
1/4" x 3/4" Screws (13).
Insert the Curl Post (70) into the Seat Brace (75) and
secure the Curl Post at the desired height with the
Adjustment Knob (45).
38 69 7O
17

1_9.Appl_,.{he WELDER PRO 992,0 decal in the location-
shown. "; 39"
WELDER
PRO 9930
40. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in
ADJUSTMENT, beginning on page 21 of this manual.
Before using the home gym, pull each cable a few times to make sure that the cables move smoothly over
the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the
cables are not properly installed, they may be damaged when heavy weight is used. If there is any
slack in the cables, you will need to remove the slack by tightening the cables. See TROUBLE-
SHOOTING AND MAINTENANCE on page 22.
18

The Cable Diagrams below and on the next page show the proper routing of the Short Cable (71), the Medium
Cable (72), and the Long Cable (73). The numbers show the correct route for each Cable. Make sure that the
Cables are routed correctly, that the Pulleys move smoothly, and that the Cable Traps do not touch or
bind the Cables. Incorrect cable routing can damage the home gym.
Short Cable (71) IMedium Cable (72) 2
Cable ID Chart
71, 74.50"
72, 140"
73, 299.25"
19

Long Cable; (73)
2
7
12
10
,--4 _ =
2O