Welcome Chimes WC8181 User manual

Exclusively distributed by
If you have any questions or comments,
contact us on:
02 9899 8833 or
email [email protected]
PO Box 6388
Baulkham Hills, NSW, 2153
4. Push the front and back parts of the push button casing
together, taking care to position the rubber seal around the edge
of the casing.
5. Using the included double-sided tape, afx the push button to
a suitable surface. Avoid locating the push button on or directly
near metallic surfaces as this may reduce the operating range.
6: Remove the battery cover of the door chime
(located on the rear of the unit).
7: Insert 3 x ‘AAA’ Batteries (not supplied), ensur-
ing that the positive and negative markings on the
battery are correctly aligned with the positive and
negative markings on the door chime. Note that only
alkaline batteries are recommended for use with this
chime.
8: Replace the battery cover.
9: If necessary, select a melody and set the volume as per the
instructions on the next page.
10: Position the door chime as needed within the range of the
push button. Note that the door chime unit is for indoor use
only. Avoid locating the door chime on or directly near metallic
surfaces as this may reduce the operating range.
Portable Wireless Chime Kit
WC8181
Components:
1: Push Button
2: Bell Push Battery
3: Portable Chime
4: LED Light
5: Speaker
6: Musical Tone selector
7: Volume control
8: Chime Batteries
1
2
8
5
3
7
6
Setup Instructions:
1: Insert a small at screwdriver into the
slot on the base of the push button.
2: Gently twist the screwdriver to sepa-
rate the front and back parts of the push
button casing.
3: Remove the black plastic tab from
the battery compartment and ensure
that the battery is securely in position.
www.welcomechimes.com.au
14/03/13 N95

Melody Selection:
The WC8181 Chime Kit has 48 musical tones to select from.
To select a tone, press the “Melody Select” button on the side
of the door chime. The chime will play
the selected tone. Continue pressing the
“Melody Select” button until the desired
tone is selected.
Volume Control Setting:
To select the Chime Volume level, press
the “Volume” button on the side of the
door chime. The chime will play the
selected tone at the selected volume.
Continue pressing the “Volume” button
until the desired volume level is selected.
Changing Batteries:
Push Button:
1: Insert a small at screwdriver into the slot on the base of
the push button.
2: Gently twist the screwdriver to separate the front and back
parts of the push button casing.
3: Remove the old battery from the holder.
4: Replace with a new ‘23A’ 12V Alkaline battery, ensuring
that the positive and negative markings on the battery are
correctly aligned with the positive and negative markings on
the push button.
5: Push the front and back parts of the push button casing
together, taking care to position the rubber seal around the
edge of the casing.
6: Test the operation of the chime kit.
Chime Unit:
1: Remove the battery cover of the door chime (located on
the rear of the unit).
2: Remove the old batteries from the holder.
3: Insert 3 x ‘AAA’ Batteries, ensuring that the positive and
negative markings on the battery are correctly aligned with
the positive and negative markings on the door chime. Note
that only alkaline batteries are recommended for use with
this chime.
4: Replace the battery cover.
5: Test the operation of the chime kit.
Troubleshooting:
In case of the door chime does not sound, please check the
following:
1: Ensure that new batteries are used in both the push but-
ton and door chime and that they are inserted correctly.
2: Check that the push button is in range of the door chime
by moving the push button and door chime close to each
other.
Technical Parameters:
1. Rated Voltage:
Receiver: 4.5V
Transmitter: 12V
2. Volume: 50 ~ 80 dB
3. Working Frequency: 433 MHz
4. Maximum Range: 60 Metres (note that range may be
affected by environmental factors and nearby interference
sources)