Well NeoGate TB400 User manual

TB400
User Manual
Version 6.11.43.14

NeoGate TB400 User Manual
2
Table of Contents
1. INTRODUCTION ...................................................................................... 4
1.1 Hardware Specification ........................................................................ 4
1.1.1 Exterior Appearance ...................................................................... 4
2. SYSTEM SET UP ...................................................................................... 5
2.1 Installation of BRI Module. ................................................................... 5
2.2 Ethernet Line Connection ..................................................................... 5
2.3 Power Supply Connection..................................................................... 6
3. NEOGATE CONFIGURATION ...................................................................... 6
3.1 Manager Login.................................................................................... 6
3.2 BRI Settings....................................................................................... 7
3.2.1 Module List................................................................................... 7
3.2.2 BRI Settings ................................................................................. 8
3.2.2.1 Basic Settings .....................................................................................8
3.2.2.2 CallerID Prefix Settings ........................................................................8
3.2.2.3 Advanced Settings ...............................................................................9
3.2.2.4 DOD settings..................................................................................... 11
3.3 VOIP Settings................................................................................... 11
3.3.1 Trunks ....................................................................................... 11
3.3.1.1 VOIP Account .................................................................................... 11
3.3.1.2 Voip Trunk ........................................................................................ 13
3.3.1.3 Service Provider ................................................................................ 14
3.3.1.4 Advanced Setting .............................................................................. 15
3.3.1.5 DOD settings..................................................................................... 16
3.3.2 SIP settings................................................................................ 16
3.3.2.1 General ............................................................................................ 16
3.3.2.2 NAT .................................................................................................17
3.3.2.3 Codes............................................................................................... 19
3.3.2.4 QOS................................................................................................. 19
3.3.2.5 Advance settings ............................................................................... 20
3.3.3 IAX settings ............................................................................... 20
3.3.3.1 General ............................................................................................ 20
3.4 Route settings .................................................................................. 21
3.4.1 Routes list .................................................................................. 21
3.4.1.1 New calling route............................................................................... 21
3.4.2 Black list .................................................................................... 24
3.5 Network Settings .............................................................................. 25
3.5.1 LAN settings ............................................................................... 25
3.5.2Firewall....................................................................................... 26
3.5.3 VLAN settings ............................................................................. 29
3.5.4 VPN Settings .............................................................................. 31
3.5.5 DDNS Settings............................................................................... 31

NeoGate TB400 User Manual
3
3.6 System Settings ............................................................................... 32
3.6.1 Options...................................................................................... 32
3.6.2 Password Settings ....................................................................... 33
3.6.3 Date and Time ............................................................................ 33
3.6.4 Backup and Restore..................................................................... 34
3.6.5 Reset and Reboot........................................................................ 34
3.6.6 Firmware Update......................................................................... 35
3.7 Reports ........................................................................................... 36
3.7.1 Call Logs .................................................................................... 36
3.7.2 System Info ............................................................................... 36
4. APPLICATION ........................................................................................ 37

NeoGate TB400 User Manual
4
1. Introduction
NeoGate Gateway for Maximum Efficiency & Cost Savings
NeoGate TB400 is a device for connecting BRI Network to VoIP Network directly,
which can support two-way communication: BRI to VoIP or VoIP to BRI.
It is the best solution ever to connect IP-based telephone systems, soft switches,
and IP-PBXs to BRI network.
1.1 Hardware Specification
1.1.1 Exterior Appearance
1) Front Side
Figure 1-1 NeoGate TB400 Front Panel Picture
No.
Identifying
①Power
Green shining: Connected, correct function.
②RUN
Green Light：Indicates the server system is in working order
③Ready
Green Light：Indicates the system is ready.
④BRI 1
Orange Shining: BRI 1 connected
①② ③④④⑤⑥ ⑦

NeoGate TB400 User Manual
5
⑤BRI 2
Orange Shining: BRI 2 connected
⑥BRI 3
Orange Shining: BRI 3 connected
⑦BRI 4
Orange Shining: BRI 4 connected
2) Back Side
2. System set up
2.1 Installation of BRI Module.
Open the case of NeoGate, adjust the pins to the slots and insert then insert the
spins into the slots.
Note1: Please turn off the device when installing the modules.
2.2 Ethernet Line Connection
NeoGate provides two 10/100M Ethernet ports with RJ45 interface and LED
indicator. Plug Ethernet line into NeoGate’s Ethernet port, and then connect
Figure 1-2 NeoGate TB400 Back
Side Picture

NeoGate TB400 User Manual
6
the other end of the Ethernet line with a hub, switch, router, LAN or WAN. Once
connected, check the status of the LED indicator. The orange LED indicates
connected successfully, while green indicates the port is working property
2.3 Power Supply Connection
NeoGate utilizes the high-performance switch power, which supply the enough
voltage and electrical energy that required by NeoGate system.
AC Input: 100~240V
DC Output: 12V,1A
Please follow the steps below to connect the NeoGate unit to a power outlet:
Connect the small end of the power cable to the power input port on the
NeoGate back panel, and plug the other end of the cable into a 100VAC power
outlet.
Check the Power LED on the front panel. A solid green LED indicates that power
is being supplied correctly.
3. NeoGate Configuration
3.1 Manager Login
From your web browser, input the IP address of the NeoGate server.
If this is the first time you are configuring NeoGate, please use the default
settings below:
IP Address: http://192.168.5.150
Username: admin
Password: password

NeoGate TB400 User Manual
7
Figure 3-1
3.2 BRI Settings
3.2.1 Module List
You can check the information of the status of BRI modules and trunks. Click
edit to configure the trunk.
Figure 3.2.1
NeoGate Status Description:
Status

NeoGate TB400 User Manual
8
OK: The port is idle.
Disconnected: No line connects to this port.
3.2.2 BRI Settings
3.2.2.1 Basic Settings
Figure 3.2.2.1
Trunk Name: A name of this Trunk. Ex: 'BRI1' etc.
Signaling: You can choose the signaling of BRI. It supports BIR-NET,
BRI-NET-PTMP, BRI CPE, BRI-CPE-PTMP.
Default DOD: You can set the default DOD here.
Max. Call Duration (min)/Per Month: Defines the maximum call duration
within a month through this SIM card. (0 it means unlimited)
Clear Stat: Set the day in a month on which the statistics data on Max. Call
Duration are deleted. This parameter is ignored if set to 0.
3.2.2.2 CallerID Prefix Settings
You can add prefix to the incoming call here.
Figure 3.2.2.2

NeoGate TB400 User Manual
9
3.2.2.3 Advanced Settings
Figure 3.2.2.3
·Switch Type:
National: National ISDN type2 (common in US)
ni1: National ISDN type1
dms100: Nortel DMS100
4ess: AT&T 4ESS
5ess: Lucent 53SS
Euroisdn: Euro ISDN
Qsig: Minimalistic protocol to build a ‘network’with two or more pbx of different
vendors.
·PRI Dialplan
Sets an option required for some (rare) switches that require a dialplan
parameter to be passed. This option is ignored by most PRI switches. It may be
necessary on a few pieces of hardware. This option can almost always be left
unchanged from the default.
·PRI Local Dialplan
Sets an option required for some (rare) switches that require a dialplan
parameter to be passed. This option is ignored by most PRI switches. It may be
necessary on a few pieces of hardware. This option can almost always be left
unchanged from the default.
·Reset Interval
Set the time in seconds between restart of unused channels. Some PBXs don't
like channel restarts. so set the interval to a very long interval e.g. 100000000
or 'never' to disable *entirely*. If you are in Israel, the following is important:
As Bezeq in Israel doesn't like the B-Channel resets happening on the lines, it is
best to set the resetinterval to 'never' when installing a box in Israel. Our past
experience also shows that this parameter may also cause issues on local
switches in the UK and China.

NeoGate TB400 User Manual
10
·Overlap Dial
Whether MyPBX can dial this switch using overlap digits. If you need Direct
Dial-in (DDI; in German \"Durchwahl\") you should change this to yes, then
MyPBX will wait after the last digit it receives.
·PRI Indication
Tells how MyPBX should indicate Busy() and Congestion() to the switch/user.
Accepted values are:
inband: MyPBX plays indication tones without answering; not available on all
PRI/BRI subscription lines
outofband: MyPBX disconnects with busy/congestion information code so the
switch will play the indication tones to the caller. Busy() will now do same as
setting PRI_CAUSE=17 and Hangup().
·Enable Facility
To enable transmission of facility-based ISDN supplementary services (such as
caller name from CPE over facility), enable this option.
·Nsf
Used with AT&T PRIs.If outbound calls are being rejected due to \"Mandatory
information element missing\" and the missing IE is 0x20, then you need this
setting.
·Echo Cancellation
Disable or enable echo cancellation.
·Hide CallerID
Whether to Hide Caller ID.

NeoGate TB400 User Manual
11
3.2.2.4 DOD settings
Spare DOD for each numbers, which is higher than the default DOD in priority
Figure 3.2.2.4
3.3 VOIP Settings
3.3.1 Trunks
We can create multiply trunks here to the provider in this page
3.3.1.1 VOIP Account
In this mode, we can create sip account in NeoGate, which will be regarded as
SIP server, so that other IP PBX or soft switch can register to NeoGate directly

NeoGate TB400 User Manual
12
Figure 3.3.1.1
·Name
Define the name of this trunk
·Type
Choose the type of this trunk, SIP or IAX, the default is SIP
·Transport
Define the transport here, UDP, TCP or TLS, the default is UDP (recommend)
·Account
The user name you defined to register this trunk
·Password
The password to register this trunk
·Enable SRTP
Define whether SRTP is enabled
·Enable IP restriction
Check this option to enhance the VoIP security for NeoGate. If this option is
enabled, only the permitted IP or Subnet mask will be able to register. In this
way, the VoIP security will be enhanced.

NeoGate TB400 User Manual
13
·Permitted ‘IP address/Subnet mask’
The input format should be ‘IP address’+’/’+’Subnet mask’.
e.g."192.168.5.100/255.255.255.255" means only the device whose IP
address is 192.168.5.100 is allowed to register this extension number.
e.g."192.168.5.0/255.255.255.0" means only the device whose IP address is
192.168.5.XXX is allowed to register this extension number
3.3.1.2 Voip Trunk
‘voip trunk’, which is used to register to another SIP Server or SIP Proxy.
·Name
Define the name of this Voip trunk
·Type
Choose the type of this trunk, SIP or IAX, the default is SIP
·Transport
Define the transport here, UDP, TCP or TLS, the default is UDP (recommend)
·Hostname/IP
Service provider’s hostname or IP address.5060 is the standard port number
used by SIP protocol. Don’t change this part if it is not required.
·Domain
Put the VoIP provider’s server domain name here.
·Username
Put the username of SIP account. Used for SIP trunk registration.
·Authorization name
Used for SIP authentication. Leave this blank if not required.
·Password
Put the password of SIP account.
·From User
All outgoing calls from this SIP Trunk will use the From User (In this case the
account name for SIP Registration) in From Header of the SIP Invite.
·Online number
Define the online number that expected by ‘Skype Connect’and some other SIP
service providers. Leave this field blank if it's no required.

NeoGate TB400 User Manual
14
·Outbound Proxy Server
A proxy that receives requests from a client, even though which may not be the
server resolved by the Request-URI.
·Enable SRTP
Define whether SRTP is enabled
·Caller ID
Define the default caller id of this trunk (default DOD)
Figure 3.3.1.2
3.3.1.3 Service Provider
·Name
Define the name of this Voip trunk
·Type
Choose the type of this trunk, SIP or IAX, the default is SIP
·Transport
Define the transport here, UDP, TCP or TLS, the default is UDP (recommend)
·Hostname/IP
Service provider’s hostname or IP address.

NeoGate TB400 User Manual
15
Note: 5060 is the standard port number used by SIP protocol. Don’t change this
part if it is not required.
Figure 3.3.1.3
3.3.1.4 Advanced Setting
·Max. Call Duration (min)
Set the maximum call duration here. 0 means no limit.
·Clear Stat
The date of each month the system will clear the call history.
·DTMF Mode
You can set the DTMF mode here (rfc2833,info,inband,auto, default is rfc2833).
·Max. Channels
Set the maximum channels here. 0 means no limit.
·Allowed Codecs
Choose the codes allowed here. (Default u-law, a-law, GSM)
Figure 3.3.1.4

NeoGate TB400 User Manual
16
3.3.1.5 DOD settings
Figure 3.3.1.5
Spare DOD for each numbers, which is higher than the default DOD in priority
3.3.2 SIP settings
3.3.2.1 General
Figure 3.3.2.1

NeoGate TB400 User Manual
17
·UDP Port
Port use for sip registrations, Default is 5060.
·RTP Port Start
Beginning of RTP port range
·RTP Port End
End of RTP port range
·Max Registration/Subscription Time
Put down the maximum duration (in seconds) of a SIP registration. Default is
3600 seconds.
·Min Registration/Subscription Time
Put down the minimum duration (in seconds) of a SIP registration. Default is 60
seconds.
·Default Incoming/Outgoing Registration Time
Default Incoming/Outgoing Registration Time: Default is 30 seconds.
·Register Attempts
The number of SIP REGISTER messages to send to a SIP Registrar before giving
up. Default is 4 (no limit).
·Register Timeout
Put down the number of seconds to wait for a response from a SIP Registrar
before timed out. Default is 20 seconds.
3.3.2.2 NAT
Note: Configuration of this section is only required when using remote
extensions.

NeoGate TB400 User Manual
18
Figure 3.3.2.2
·Enable STUN
STUN (Simple Traversal of UDP through NATs) is a protocol for assisting devices
behind a NAT firewall or router with their packet routing.
·STUN Address
The STUN server allows clients to find out their public address, the type of NAT
they are behind and the internet side port associated by the NAT with a
particular local port. This information is used to set up UDP communication
between the client and the VOIP provider and so establish a call.
·External IP Address
Put down the IP address that will be associated with outbound SIP messages if
the system is in a NAT environment.
·External Host
Alternatively you can specify an external host, and the system will perform DNS
queries periodically.
This setting is only required when your public IP address is not static. It is
recommended that a static public IP address be used with this system. Please
contact your ISP for more information.
·External Refresh Interval
If an external host has been supplied, you may specify how often the system will
perform a DNS query on this host. This value is specified in seconds.
·Local Network Identification
It’s used to identify the local network using a network number/subnet mask pair
when the system is behind a NAT or firewall.
Some examples of this are as follows:

NeoGate TB400 User Manual
19
'192.168.0.0/255.255.0.0' : All RFC 1918 addresses are local networks;
'10.0.0.0/255.0.0.0' : Also RFC1918;
'172.16.0.0/12':Another RFC1918 with CIDR notation;
'169.254.0.0/255.255.0.0' : Zero conf local network.
Please refer to RFC1918 for more information.
·NAT Mode
Global NAT configuration for the system. The options for this setting are as
follows:
Yes = Use NAT. Ignore address information in the SIP/SDP headers and reply to
the sender's IP address/port.
No = Use NAT mode only according to RFC3581.
Never = Never attempt NAT mode or RFC3581 support.
Route = Use NAT but do not include report in headers.
·Allow RTP Reinvite
By default, the system will route media steams from SIP endpoints through
itself. Enabling this option causes the system to attempt to negotiate the
endpoints to route packets to each other directly, bypassing the system. It is not
always possible for the system to negotiate endpoint-to-endpoint media
routing.
3.3.2.3 Codes
If G729 is enabled, please input the license here.
Figure 3.3.2.3
3.3.2.4 QOS
QOS (Quality of Service) is a major issue in VOIP implementations. The issue is
how to guarantee that packet traffic for a voice or other media connection will
not be delayed or dropped due interference from other lower priority traffic.
When the network capacity is insufficient, QoS could provide priority to users by
setting the value.

NeoGate TB400 User Manual
20
Figure 3.3.2.4
3.3.2.5 Advance settings
Define where to get the DID and the caller ID
Figure 3.3.2.5
·From field
Define where to get the caller ID
·To field
Define where to get the DID
3.3.3 IAX settings
If the trunk you have created is IAX, you need configure some details here
3.3.3.1 General
Figure 3.3.3
·Bind Port
Port use for IAX2 registrations, Default is 4569.