Installation — Under Counter
65
Using the optional Wellness Under-Counter Adaptor Kit you can easily convert your above-
counter Wellness Kitchen S-IIITM to an under-counter model. Please review all installation steps
before you begin to ensure no conflicts exist with your desired location. Wellness recommends
a licensed plumber is hired to connect this unit. Improper installation may void warranty.
PLEASE C HEC K TO EN SU RE ALL PAR TS ( SHOWN B ELOW ) ARE INCLU D ED WITH YO UR U NDER- CO UN TE R KI T.
1. Leak Controller
AA Batteries (4)
2. Leak Controller
Mounting Bracket
3. Leak Controller
Mounting Screws (2)
4. Leak Controller Sensor
5. Leak Controller
Shut-off Valve
6. Black Tubing (3-4' pieces,
2 w/ elbow connectors)
7. Cold Water "T" Adaptor, &
Compression Fittings
8. Faucet Mounts (6 pieces)
and Compression Fittings
9. Faucet
Disconnect Supply Hoses
Note: This is necessary only if
re-locating the Wellness Kitchen
S-III from the counter-top to
under-the-counter.
Turn the filter so the bottom is
facing up, and with the digital
flow meter facing up also (to
keep water from entering
electronics). Remove the
diverter valve hoses by pressing
down on the side of the white,
locking-collar ring with your
fingernail or a small flat head
screwdriver and gently but firmly
pulling the hose out.
(See illustration Cnext page.)
Step 1. Install Auxiliary Faucet
Note: See faucet installation
instructions on packaging.
Locate faucet (#9) and faucet
mounts (#8). Use sink auxiliary
hole, remove a sink accessory
or drill a ½" hole in your sink to
accommodate the threaded
pipe on the faucet. Install faucet
(#9) with washers (#8) and
tighten into place using the star
washer and lock nut. Tighten
firmly with wrench to keep
faucet in place.
Be careful not to overtighten.
(Instructions for tubing
connection to follow in Step 4.)
Step 2. Install Shut-off Valve
Mount
bracket (#2)
on a flat,
vertical surface under the sink
.
Make
sure the spot has sufficient
side clearance
to accommodate
the tubing (#6) to be attached.
Using the supplied screws (#3)
and a Phillips screwdriver, install
the bracket as shown above left.
Once the bracket is installed,
mount the shut-off valve (#5) as
shown in photo above right.
Refer to the shut off valve
Installation and Operation Guide.
Failure to review said instructions
could result in unit malfunction.
2. Locate tubing with blue elbow
on one end. Attach blue
elbow end to the Wellness
Kitchen S-III at its blue-
colored quick-connect fitting
labeled "OUT". Connect other
end to the auxiliary faucet
compression fitting (#8)
using method described in
illustration
E
below.
3. Locate the tubing with a
green elbow end.
Attach
green elbow end to the
Wellness Kitchen S-III at
its green-colored quick-
connect fitting labeled
"IN".
Connect the tubing's
other end to the available
quick-connect fitting on the
leak controller shut-off
valve (the unused side)
.
Remember,
in all quick-
connect fittings, leakage
may occur if not inserted
completely (see C).
Step 5. Check Connection
Turn on the Wellness faucet.
Next, slowly turn on the cold
water valve. Once water flows
freely through the Wellness
faucet, turn it off.
The system is now pres-
surized. Immediately check
connections on the cold
water adaptor, the Wellness
faucet, both sides of the leak
controller, shut-off valve, and
the "IN" & "OUT" Wellness
Kitchen S-III connections for
any leaks.
When no leaks are apparent,
skip to step 6. If a leak
occurs, shut off the main
cold water valve and attempt
to tighten the fittings and
connections. Then, go back
to the beginning of step 5.
If you are not able to isolate
or repair the leak, contact
customer service.
Step 6. Final Step
After you have determined
that the unit is not leaking
and a steady flow is passing
through the faucet, place a
paper towel (supplied) next
to the filter and place the
leak sensor on towel. If one
side of the unit is at a lower
elevation than another side,
place towel on lower side.
(shown in Dabove)
Congratulations! Enjoy
your Wellness Kitchen S-III!
1
2
5
4
6
3
7
9
8
Note: Elbows & tubing will insert
3
/
4
" before it is seated. Press white ring to remove.
elbows or
tubing
valve hole
C
Step 3.
Install Cold Water Adaptor
Ensure cold water valve is
shut off. Place supplied "T"
adapter's (#7) compression
nut with threads
facing out on
tubing without
elbows .
Insert the small
brass tube in-
side the hose end (see A)
& push in completely to the
flare top. Connect that end
to the supplied "T" adapter
fitting. Secure with a wrench.
Disconnect cold-water line
from its shutoff
valve. Attach
"T" adaptor to
shutoff valve
and tighten.
Next, attach
cold-water line
to "T" adapter's
top male threads (see B).
Step 4. Connect Tubing
Note: Make sure your
Wellness Kitchen S-III is in its
final position before cutting
enclosed tubing to fit; use a
sharp tool to ensure flush cut.
1. Connect the cold-water
supply tubing (Step 3) to
leak controller shut-off
valve (either side is fine).
This is done by inserting
the tube fully into its quick-
connect fittings (see C).
Insert tubing fully into place
in all quick-connect fittings.
Leakage may occur if not
in completely (see C).
D
B
A
Faucet
washers
above
counter top
Faucet
washers
below
counter top
Slip compression nut A & compression washer B over tubing, insert brass tube C into
tubing completely to flared top, then connect compression nut A to faucet thread D.
ABCD
E